PowMr POW-LVM5K-48V-N

Contents

User Manual

PowMr 5KW 48V Hybrid Solar Inverter

Model: POW-LVM5K-48V-N

Important Safety Instructions

Please save these instructions for future use!

This manual contains all safety, installation and operating instructions for the POW-LVM5K Series all-in-one solar charge inverter.

General Safety Precautions

  • Non-safety voltage exists inside the all-in-one solar charge inverter. To avoid personal injury, users shall not disassemble the all-in-one solar charge inverter themselves. Contact our professional maintenance personnel if there is a need for repair.
  • Do not place the all-in-one solar charge inverter within the reach of children.
  • Do not install the all-in-one solar charge inverter in harsh environments such as moist, oily, flammable or explosive, or heavily dusty areas.
  • The mains input and AC output are high voltage, so please do not touch the wiring terminals.
  • The housing of the all-in-one solar charge inverter is hot when it is working. Do not touch it.
  • Do not open the terminal protective cover when the all-in-one solar charge inverter is working.
  • It is recommended to attach proper fuse or circuit breaker to the outside of the all-in-one solar charge inverter.
  • Always disconnect the fuse or circuit breaker near the terminals of PV array, mains and battery before installing and adjusting the wiring of the all-in-one solar charge inverter.
  • After installation, check that all wire connections are tight to avoid heat accumulation due to poor connection, which is dangerous.
  • The all-in-one solar charge inverter is off-grid. It is necessary to confirm that it is the only input device for load, and it is forbidden to use it in parallel with other input AC power to avoid damage.

Product Overview

The PowMr 5KW-48V-N series is a new type of mixed solar energy storage inverter, integrating solar energy storage, municipal power charge storage, and AC sine wave output. It features DSP control and advanced control algorithms for high response speed, reliability, and industrial standards. It offers four charge modes (solar only, mains priority, solar priority, mixed charge) and two output modes (inverting and mains power bypass) to suit various application needs.

The solar charge module utilizes optimized MPPT tracking technology for real-time maximum power point tracking of the photovoltaic array. The AC-DC charge module ensures stable and reliable battery charging with wide AC voltage input and comprehensive protection. The DC-AC inverter module, based on full digital intelligent design, uses advanced SPWM technology to output pure sine wave, suitable for various AC loads.

Front view of the PowMr 5KW Hybrid Solar Inverter
Figure 1: Front view of the PowMr 5KW Hybrid Solar Inverter.
Angled view of the PowMr 5KW Hybrid Solar Inverter
Figure 2: Angled view of the PowMr 5KW Hybrid Solar Inverter.
Key features and specifications of the 5000W Off-Grid Solar Inverter
Figure 3: Key features and specifications of the 5000W Off-Grid Solar Inverter, highlighting 5KW AC Output Power, 40A Max. AC Charging, 80A Max Hybrid Charging Current, and 150V Starting Voltage.
Applications of the solar inverter, including RV, Home Storage, Camping, and Solar Power System
Figure 4: Various applications for the solar inverter, such as RV, Home Storage, Camping, and Solar Power Systems.

Basic System Introduction

A complete system includes the following parts:

  1. Photovoltaic module: Converts light energy into direct current (DC) to charge the battery via the inverter, or directly inverts DC to alternating current (AC) to supply power to the load.
  2. Mains or generator: Connected at the AC input, it can supply power to the load and charge the battery. If no mains power or generator is connected, the system can still operate normally, with load power supplied by the battery and photovoltaic modules.
  3. Battery: Ensures normal power consumption of the system load when solar energy or mains supply is insufficient.
  4. Household load: Can be connected to various household and office AC loads (refrigerators, lamps, televisions, fans, air conditioners, etc.).
  5. Inverting and control all-in-one inverter: The energy conversion device of the whole system.

The specific system wiring mode is determined by the actual application scenario.

Basic System Introduction diagram showing PV panel, generator, utility, external battery packs, home appliances connected to the inverter.
Figure 5: Basic System Introduction diagram illustrating the connections between PV panel, generator, utility, external battery packs, home appliances, and the inverter.

Production Overview Diagram

Production Overview diagram with numbered parts of the inverter.
Figure 6: Production Overview diagram showing the inverter's components and ports. (1) Overload protector, (2) ON/OFF rocker switch, (3) AC input port, (4) AC output port, (5) Grounding screw hold, (6) RS485-2 communication port, (7) USB communication port, (8) RS485-1 communication port, (9) Dry contact port, (10) Cooling fan, (11) Battery port, (12) Cooling fan, (13) PV port, (14) Touch key, (15) Indicator light, (16) LCD screen.

Dimension Drawing

Dimension Drawing of the inverter with measurements.
Figure 7: Dimension drawing of the inverter, showing approximate dimensions of 433.9mm (height), 426mm (mounting height), 210mm (width), 402mm (depth), and 121.8mm (bottom depth).

Setup and Installation

Installation Notice

  • Take care while installing the battery. When installing lead-acid liquid batteries, wear goggles. Wash any body part contacting battery acid with clear water immediately.
  • Do not place any metal object beside the battery to prevent short circuits.
  • Acid gas may be generated during battery charge. Ensure good ventilation around the environment.
  • During cabinet installation, reserve sufficient space around the inverter for heat dissipation. Do not install the inverter and lead-acid liquid battery in the same cabinet to avoid corrosion from acid gas.
  • Only batteries consistent with the inverter type can be charged.
  • Loose connections and corroded wires can cause excessive heat, melting insulation, burning materials, or fire. Ensure all connectors are tightened and wires are fixed with ties.
  • Conductors should be selected based on a current density no greater than 5A/mm².
  • Outdoor installations must be protected from direct sunlight and rain.
  • After the power switch is turned off, high voltage may still be present inside the inverter. Do not open or touch internal components until capacitors are fully discharged.
  • Do not install the inverter in humid, greasy, flammable, explosive, dusty, or other severe environments.
  • The polarity of the battery input must not be reversed, as this can damage the device or cause unpredictable dangers.
  • AC supply input and AC output are high voltage; do not touch the wires.
  • Do not touch the fan when it is working to prevent injury.
  • Confirm that the inverter is the sole power supply for the load device. Do not use it in parallel with other AC power sources to avoid damage.

Select the Mount Location

Confirm the installation position and heat dissipation space. The inverter should be mounted on a wall surface.

Ensure sufficient airflow through the cooling fins. Reserve at least 200mm space at the left and right air outlets to guarantee heat loss through natural convection.

Installation Spacing diagram showing required clearances around the inverter.
Figure 8: Recommended installation clearances. Maintain at least 500mm above and below, and 200mm on the sides for proper ventilation.

WARNING

Danger of explosion! Never install the all-in-one inverter and lead-acid liquid battery into the same sealed space or in a sealed place with probable accumulation of battery gas.

Mount the Inverter

Install the unit by screwing two screws. It's recommended to use M6 screws.

Preparation for Wiring

Before connecting all wirings, please take off the bottom cover by removing two screws.

Inverter with bottom cover removed, showing internal connections.
Figure 9: Inverter with the bottom terminal cover removed, exposing the wiring terminals for battery, solar array, AC input, and AC output.

Wiring Specification and Breaker Type

For wiring and installation, observe national and local electrical specifications.

PV Input Wiring

The minimum wire diameter for the photovoltaic array is calculated based on its short circuit current. Refer to the short circuit current value in the PV array specification. The short circuit current of the array cannot exceed the maximum input current of PV.

ModelWire DiameterMax. PV input currentCircuit breaker Spec
POW-LVM5K-48V-N6mm²/10AWG22A2P-25A

Note: The voltage in series shall not exceed maximum PV input open-circuit voltage.

AC Input Wiring

ModelWire DiameterMax. bypass input currentCircuit breaker Spec
POW-LVM5K-48V-N10mm²/7AWG63A2P-63A

Note: There is already a corresponding breaker at the input connection point of mains supply. Therefore, it is not necessary to add one more.

Battery Wiring

ModelWire DiameterRated Battery Discharge CurrentMax. Charge CurrentCircuit Breaker Spec
POW-LVM5K-48V-N30mm²/7AWG125A80A2P-200A

AC Output Wiring

ModelWire DiameterRated Inverter AC Output currentMax. bypass output currentCircuit Breaker Spec
POW-LVM5K-48V-N10mm²/7AWG42A63A2P-63A

Note: The wire diameter is only for reference. In case of long distance between photovoltaic array and all-in-one inverter or between all-in-one inverter and battery, use thicker wire to reduce voltage drop and improve system performance.

NOTICE

Above wire diameter and breaker are only for reference. Please select appropriate wire diameter and breaker based on practical condition.

AC Input/Output Wiring

  1. Before AC input/output wiring, disconnect the external breaker and confirm the cable thickness.
  2. Connect AC input wire: Connect ground lead first, then live wire (L), and neutral wire (N).
  3. Connect AC output wire: Connect ground lead first, then live wire (L), and neutral wire (N). The ground wire connects to the grounding screw hold through a shaped terminal.
AC Input/Output Wiring diagram showing terminal connections for AC IN and AC OUT.
Figure 10: AC Input and Output wiring terminals. Ensure correct connection of Ground (⚡), Live (L), and Neutral (N) wires.

NOTICE

Use thick ground cable as far as possible (with cable section not less than 4mm²), place the ground point to be close to the all-in-one inverter as far as possible and choose shorter ground wire to the greatest extent.

PV Input Wiring

  1. Before wiring, disconnect the external breaker and confirm the cable thickness.
  2. Correctly connect PV input wire: PV+ (positive input pole) and PV- (negative input pole).
PV Input Wiring diagram showing terminal connections for PV+ and PV-.
Figure 11: PV Input wiring terminals. Connect PV+ to the positive input pole and PV- to the negative input pole.

Battery Wiring

  1. Before wiring, disconnect the external breaker and confirm the cable thickness. BAT wire should be connected with the machine via O-shaped terminal (recommended 6mm inside diameter). Compress the O-shaped terminal firmly to prevent excessive heating.
  2. Correctly connect BAT wire: BAT+ (positive battery pole) and BAT- (negative battery pole).
Battery Wiring diagram showing terminal connections for BAT+ and BAT-.
Figure 12: Battery wiring terminals. Connect BAT+ to the positive battery pole and BAT- to the negative battery pole.

WARNING

  • Input from mains supply, AC output, and photovoltaic array may generate high voltage. Before wiring, ensure the breaker or fuse is open.
  • During wiring, pay attention to safety. Do not close the breaker or fuse. Ensure '+' and '-' poles are correctly connected. A breaker must be installed at the battery end. Before wiring, open the breaker to prevent strong electric sparks. Avoid battery short circuits.
  • If the inverter is in an area with frequent thunder, install an external arrester at the PV input terminal.

Final Assembly and Startup

  1. After wiring, inspect all connections for correctness and tightness. Verify positive and negative input poles for battery and PV, and ensure AC input is not incorrectly connected to AC output.
  2. Once wiring is reliable and correct, install the terminal protection cover.
  3. Startup: First, close the breaker at the battery end. Press the rocker switch on the lower left side to 'ON'. The 'AC/INV' indicator light will flash, indicating normal inverter operation.
  4. Next, close the breakers for the photovoltaic array and mains supply.
  5. Finally, after AC output is normal, turn on AC loads one by one, starting with high impact current loads, to avoid protection actions from simultaneous load activation. The inverter will operate according to the set mode.

NOTICE

  • If power is supplied to different AC loads, turn on loads with great impact current first, then loads with little impact current after the first load stabilizes.
  • In case of abnormal operation or display, refer to the 'Troubleshooting' section.
Video 1: Installation guide for the PowMr Solar Inverter, demonstrating mounting, wiring connections for battery, solar array, AC input/output, grounding, and final startup steps.

Operating Mode

Charge Mode

  • Photovoltaic priority: Mains charge starts only when PV is out of work. Maximizes solar energy use. Suitable for areas with stable power grids and expensive electricity.
  • Mains supply priority: Mains supply charges the battery preferentially. PV charge starts only when mains supply is valid.
  • Mixed charge: Prioritizes PV MPPT charge. Mains supply supplements if PV energy is insufficient. Stops mains charge if PV energy is sufficient. Fastest charging, suitable for unstable grids.
  • Only solar: Only PV charge is used, no mains supply. Maximizes energy saving. Suitable for areas with good light conditions.

Output Mode

  • Photovoltaic priority mode: PV and battery supply power to the load. Switches to mains supply when PV is invalid. Maximizes solar energy use and maintains battery charge. Suitable for stable power grids.
  • Mains supply priority mode: Switches to inverter for power supply only when mains supply is invalid (backup UPS). Applicable to areas with unstable power grids.
  • Inverter priority mode: Switches to mains supply only in case of battery undervoltage. Maximizes DC energy use. Applied to stable power grids.
  • Mixed functions mode: When the battery is unavailable or fully charged, the load is provided by PV and commercial power, with maximum PV output.

Operation and Display Panel

The inverter features an LCD screen and 3 LED indicator lights to dynamically display system data and operation states.

Touchable Keys

Function KeyDescription
SETEnter/exit setting menu
UPLast option
DOWNNext option
ENTConfirm/enter option under setting menu

LED Indicators

Indicator lightColorDescription
AC/INVYellowConstant on: mains supply output
Flashing: inverter output
CHARGEGreenFlashing: battery in charge
Constant on: charge completed
FAULTRedConstant on: fault state

Introduction to LCD Screen

LCD screen overview with various icons and indicators.
Figure 13: LCD screen display showing various icons for AC input, PV input, battery status, inverter status, and load percentage.

LCD Icons and Functions

IconFunction
⚡Indicating that AC input end has been connected to power grid
☀Indicating that PV input end has been connected to solar battery panel
🔋Indicating machine has been connected to battery (with charge level)
⚡Indicating that inverter circuit is working.
BYPASSIndicating that the machine is in mains supply bypass work mode
OVER LOADIndicating that AC output is in overload state
100% / 25%Indicating percentage of AC output load
Li / SLAIndicating battery type (Lithium / Lead-acid)
🔇Indicating that buzzer is not enabled
⚠Indicating alarm of machine
ERRORIndicating that the machine is in fault state.
⚙Indicating that the machine is in setting mode.

Real-time Data View Method

In the LCD main screen, press the "UP" and "DOWN" keys to view different real-time data:

PageLeft Parameter of ScreenMiddle Parameter of ScreenRight Parameter of Screen
1Battery input voltageFault codeOutput voltage
2PV temperaturePV output KW
3PV input voltagePV output current
4Input battery currentOutput battery current
5Input battery KWOutput battery KW
6AC input frequencyAC output load frequency
7AC input voltageAC output load current
8Input voltageOutput load KVA
9INV temperatureINV output load KW
10APP software versionBootloader software version
11Model Battery Voltage RatingModel Output Power Rating
12Model PV Voltage RatingModel PV Current Rating

Setting Parameters

To enter/exit the setting menu, press the "SET" key. Use "UP" and "DOWN" to select the parameter item code, then "ENT" to edit. Adjust values with "UP" and "DOWN", then "ENT" to confirm.

Battery Type Parameters (Lead-acid Battery)

ParametersSealed lead acid battery (SLD)Colloidal lead acid battery (GEL)Vented lead acid battery (FLD)User-defined (USE)
Overvoltage disconnection voltage60V60V60V60V
Equalizing charge voltage58.4V56.8V59.2V40~60V (Adjustable)
Boost charge voltage57.6V56.8V58.4V40~60V (Adjustable)
Floating charge voltage55.2V55.2V55.2V40~60V (Adjustable)
Undervoltage alarm voltage44V44V44V40~60V (Adjustable)
Low voltage disconnection voltage42V42V42V40~60V (Adjustable)
Discharge limit voltage40V40V40V40~60V (Adjustable)
Over-discharge delay time5s5s5s1~30s (Adjustable)
Equalizing charge duration120 mins-120 mins0~600 mins (Adjustable)
Equalizing charge interval30 days-30 days0~250 days (Adjustable)
Boost charge duration120 mins120 mins120 mins10~600 mins (Adjustable)

Battery Type Parameters (Lithium Battery)

ParametersTernary lithium battery (N13)Ternary lithium battery (N14)Lithium iron phosphate battery (L16)Lithium iron phosphate battery (L15)Lithium iron phosphate battery (L14)User-defined (USE)
Overvoltage disconnection voltage60V60V60V60V60V60V
Equalizing charge voltage-----40~60V (Adjustable)
Boost charge voltage53.2V (Adjustable)57.6V (Adjustable)56.8V (Adjustable)53.2V (Adjustable)49.2V (Adjustable)40~60V (Adjustable)
Floating charge voltage53.2V (Adjustable)57.6V (Adjustable)56.8V (Adjustable)53.2V (Adjustable)49.2V (Adjustable)40~60V (Adjustable)
Undervoltage alarm voltage43.6V (Adjustable)46.8V (Adjustable)49.6V (Adjustable)46.4V (Adjustable)43.2V (Adjustable)40~60V (Adjustable)
Low voltage disconnection voltage38.8V (Adjustable)42V (Adjustable)48.8V (Adjustable)45.6V (Adjustable)42V (Adjustable)40~60V (Adjustable)
Discharge limit voltage36.4V39.2V46.4V43.6V40.8V40~60V (Adjustable)
Over-discharge delay time30s (Adjustable)30s (Adjustable)30s (Adjustable)30s (Adjustable)30s (Adjustable)1~30s (Adjustable)
Equalizing charge duration-----0~600mins (Adjustable)
Equalizing charge interval-----0~250days (Adjustable)
Boost charge duration120mins (Adjustable)120mins (Adjustable)120mins (Adjustable)120min (Adjustable)120mins (Adjustable)10~600 mins (Adjustable)

Other Functions

Dry Node Function

This dry node can control the switch of a diesel generator to charge the battery.

Dry Node Function diagram showing NO, N, NC terminals.
Figure 14: Dry Node terminals (NO, N, NC). Under normal conditions, NC-N is closed and NO-N is open. When battery voltage reaches low-voltage disconnection, the relay coil is energized, NO-N closes, and NC-N opens. This can drive resistive loads (125VAC/1A, 230VAC/1A, 30VDC/1A).

RS485 Communication Function

The inverter has two RS485 communication ports (RS485-1 and RS485-2) with two functions:

  1. RS485 communication with lithium battery BMS (RS485-2, customizable).
  2. RS485-1 connects to a WiFi/GPRS communication module (developed by PowMr) for remote monitoring and control via mobile app.
RS485 Communication Function diagram showing pinout.
Figure 15: RS485 pinout. Pin 1 is 5V power supply, Pin 2 is GND, Pin 7 is RS485-A, and Pin 8 is RS485-B.

USB Communication Function

This port is for USB communication with the upper computer software. Install the corresponding "USB to serial port chip CH340T driver" on your computer.

USB Communication Function diagram showing USB port.
Figure 16: USB communication port.

Protection Functions

No.Protection FunctionNote
1Current limiting protectionWhen the charge current of the configured PV array exceeds the rated current of PV, it will be charged at the rated current.
2Anti-reverse charge protection at nightAt night, because the battery voltage is greater than that of the PV module, the battery shall be protected against discharge through the PV module.
3AC input over-voltage protectionWhen the AC voltage exceeds 140V (120V model), the AC charge will be stopped and converted to inverter for output.
4AC input under-voltage protectionWhen the AC voltage is lower than 90V (120V model), the AC charge will be stopped and converted to inverter for output.
5Battery overvoltage protectionWhen the battery voltage reaches the overvoltage breaking voltage point, charge from PV and AC power to the battery shall be automatically stopped to prevent the battery from being damaged due to overcharge.
6Battery low-voltage protectionWhen the battery voltage reaches the low-voltage breaking voltage point, the discharge to the battery will automatically stopped to prevent the battery from damage owing to over discharge.
7Load output short circuit protectionIn case of short-circuit fault at the load output end, the output of AC voltage can be turned off immediately and then restored 1 minute later. After trying for 3 times, the output load end is still in short circuit state, it is required to eliminate the short circuit fault of the load at first, and then turn on the machine again to restore normal output.
8Radiator overtemperature protectionIn case of excessive internal temperature, the all-in-one inverter shall stop charge and discharge; after the temperature returns to normal state, the all-in-one inverter shall restore charge and discharge.
9Overload protectionThere is output within 3 minutes after overload protection. The output is turned off in case of 5 times of continuous overload until the machine is turned on again. Specific overload grade and duration are shown in the technical parameter able after the manual.
10AC reverse flowing protectionPrevent AC power inverted from battery inverting against reverse flowing into bypass AC input.
11Bypass overcurrent protectionBuilt-in AC input overcurrent protection breaker.

Troubleshooting

FaultSolving Measures
No display on screenCheck whether the battery air switch or PV air switch is closed; whether the switch is in "on" state; press any key on the screen to exit from the screen sleep mode.
Charge battery overvoltage protectionMeasure whether the battery voltage exceeds 60V, and disconnect the photovoltaic array air switch and the AC air switch.
Battery undervoltage protectionAfter the battery charge restores to be above low-voltage disconnection recovery voltage.
Fan faultCheck if the fan doesn't work or if it's blocked by something else.
Radiator overtemperature protectionWhen the device cools below the overtemperature recovery temperature, it shall restore to normal charge and discharge control.
Bypass overload protection, inverting overload protectionDecrease consumer; Restart all-in-one inverter and the load output is restored.
Inverting short-circuit protectionCarefully check load connection condition, clear short-circuit fault point; After power on again, the load output is restored.
PV overvoltageCheck whether PV input voltage exceeds maximum allowable input voltage with a multimeter.
No connection alarm of batteryCheck whether the battery is not disconnected or whether the breaker at the battery side is not closed.

Meaning of Fault Code

Fault CodeFault NameAffecting output or notNote
【01】BatVoltLowYesBattery undervoltage alarm
【02】BatOverCurrSwYesAverage overcurrent software protection for battery discharge
【03】BatOpenYesNo connection alarm of battery
【04】BatLowEodYesStop discharge alarm for battery undervoltage
【05】BatOverCurrHwYesBattery overcurrent hardware protection
【06】BatOverVoltYesCharge overvoltage protection
【07】BusOverVoltHwYesBus overvoltage hardware protection
【08】BusOverVoltSwYesBus overvoltage software protection
【09】PV VoltHighNoPV overvoltage protection
【10】PV OCSwNoPV overcurrent software protection
【11】PV OCHwNoPV overcurrent hardware protection
【12】bLineLossNoAC power failure
【13】OverloadBypassYesBypass overload protection
【14】OverloadInverterYesInverter overload protection
【15】AcOverCurrHwYesInverter overcurrent hardware protection
【17】InvShortYesInverter short-circuit protection
【19】OverTemperMpptNoPV radiator overtemperature protection
【20】OverTemperInvYesOvertemperature protection of inverter radiator
【21】FanFailYesFan fault
【22】EEPROMYesMemory fault
【23】ModelNumErrYesInaccurate model setting
【26】RlyShortYesInverted AC Output Backfills to Bypass AC
【29】BusVoltLowYesBus undervoltage protection
【32】BatCapacityLowStopYesInverter stops when battery capacity is low (setting BMS to enable validity)
【34】CanCommFaultYesCAN communication fault in parallel operation
【58】BMS communication errorNoCheck whether the communication line is connected correctly and whether [33] is set to the corresponding lithium battery communication protocol
【59】BMS alarmNoCheck the BMS fault type and troubleshoot battery problems
【60】BMS battery low temperature alarmNoBMS alarm battery low temperature
【61】BMS battery over temperature alarmNoBMS alarm battery over temperature
【62】BMS battery over current alarmNoBMS alarm battery over current.
【63】BMS battery undervoltage alarmNoBMS alarm low battery.
【64】BMS battery over voltage alarmNoBMS alarm battery over voltage

System Maintenance

To maintain optimum and permanent operation performance, check the following items semiannually:

  1. Confirm that the air flow around the inverter is not blocked. Remove any dirt or debris from the radiator.
  2. Check whether the insulation of all exposed wires is damaged due to sun exposure, friction, dry rot, insect or rat damage. Repair or replace wires if necessary.
  3. Verify that the indication and display are consistent with device operation. Pay attention to any fault or error display and take corrective measures.
  4. Check all terminals for corrosion, insulation damage, high temperature or burning/discoloration signs, and tighten terminal screws.
  5. Check for dirt, nesting insects, and corrosion. Clean as required.
  6. If the arrester has failed, replace it to protect the inverter and other devices against lightning damage.

WARNING

Danger of electric shock! To perform operations, ensure all power supplies to the inverter are disconnected and all capacitors are discharged. Then, inspection or operation can be performed.

Damages Not Covered

The manufacturer is not responsible for the following damages:

  • Damage caused by improper use or use in inappropriate places.
  • Open-circuit voltage of photovoltaic module exceeds maximum allowable voltage.
  • Damage caused by operation ambient temperature beyond the limited range.
  • Personally taking apart and maintaining the inverter.
  • Damage caused by force majeure (e.g., transportation or handling).

Technical Specifications

AC Mode

ParameterValue
Rated input voltage110/120Vac
Input voltage range(90Vac-140Vac)
Frequency50Hz/60Hz (auto-sensing)
Frequency range47±0.3Hz ~ 55±0.3Hz (50Hz); 57±0.3Hz ~ 65±0.3Hz (60Hz)
Overload/short-circuit protectionBreaker
Efficiency>95%
Conversion time (Bypass and inverting)10ms (Typical value)
AC reverse flowing protectionYes
Maximum bypass overload current63A

Inverting Mode

ParameterValue
Output voltage waveformPure sine wave
Rated output power (VA)5000
Rated output power (W)5000
Power factor1
Rated output voltage (Vac)120Vac
Output voltage error± 5%
Output frequency range (Hz)50Hz ± 0.3Hz; 60Hz ± 0.3Hz
Efficiency>90%
Overload protection(102%<load<110%) ±10%: reporting error and turn off the output after 5 minutes;
(110%<load<125%) ±10%: reporting error and turn off the output after 10 seconds;
Load>125% ±10%: reporting error and turn off the output after 5 seconds;

AC Charge

ParameterValue
Battery typeLead acid or lithium battery
Maximum charge current40A
Charge current error± 5Adc
Charge voltage range40-60Vdc
Short-circuit protectionBreaker and blown fuse
Breaker specification63A
Overcharge protectionTurn off charge after 1min alarm

Solar Charge

ParameterValue
Maximum PV open-circuit voltage500Vdc
PV operation voltage range120-500Vdc
MPPT voltage range120-450Vdc
Battery voltage range40-60Vdc
Maximum input power5500W
Charge current range of solar energy (settable)0-80A
Charge short-circuit protectionBlown fuse
Wiring protectionInverse wiring protection

General Specifications

ParameterValue
Peak power10000VA
Loaded motor capacity4HP
Output short-circuit protectionBreaker
Specification of bypass breaker63A
Rated battery input voltage48V (minimum start voltage 44V)
Battery voltage range40.0Vdc~60Vdc ± 0.6Vdc (settable LCD screen)
Power saving modeLoad ≤50W
Operation temperature range-10°C ~ 55°C
Storage temperature range-25°C ~ 60°C
Humidity range5% to 95% (three-proof paint protection)
Noise≤60dB
Thermal dissipationForced cooling with adjustable air speed
Communication interfaceUSB/RS485 (WiFi/GPRS)/dry node control
Dimension (L*W*D)426mm*322mm*126mm
Weight (kg)11.5

Authentication Specification

ParameterValue
Specification authenticationCE(IEC62109)/CETL(UL 1741 C22.2 NO.107.1)/FCC/SAA
EMC authentication gradeEN61000

User Tips

  • Battery-less Operation: This model can work without batteries in 'Mixed functions mode' where the load is provided by PV and commercial power.
  • Output Voltage: The inverter provides 110/120Vac output. It does not support 220V output.
  • Weight: The unit weighs approximately 11.5 kg.

Warranty and Support

Warranty

The PowMr 5KW 48V Hybrid Solar Inverter comes with an 18-month warranty.

Contact Information

For technical support, inquiries, or service, please contact:

  • Company: SHENZHEN HEHEJIN INDUSTRIAL CO.,LTD
  • Tel/Fax: +86 755-28219903
  • Email: support@powmr.com
  • Web: www.powmr.com
  • Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.