Toyota ATK-998

Contents

Toyota LED License Plate Light Instruction Manual

Model: ATK-998

1. Product Overview

This manual provides essential information for the safe and effective use of your Toyota LED License Plate Light. Please read it thoroughly before installation and operation.

Toyota LED License Plate Lights with IP68 Waterproof rating and key features

Figure 1: Toyota LED License Plate Lights highlighting IP68 Waterproof rating, super brightness, perfect substitute design, long lifespan, and higher quality construction.

Video 1: Product demonstration showing the LED license plate lights rotating and illuminating.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord (if applicable) out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use (vehicle license plate illumination).
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Ensure the vehicle's power is off before attempting installation or removal.

For detailed compliance information, please refer to the User Manual PDF.

3. Setup & Installation

3.1 Compatible Models

This LED License Plate Light Assembly is designed for direct replacement in the following Toyota models:

  • Toyota Yaris (2012-2016)
  • Toyota Camry (2012-2016)
  • Toyota Vitz (2011-2016)
  • Toyota Prius C (2012-2016)
  • Toyota SAl (2014-2016)
  • Toyota Noah (2014-2016)
  • Toyota Voxy (2014-2016)
  • Toyota Esquire (2014-2015)
  • Toyota Verso/Ractis (2011-2016)
  • Toyota Corolla Fielder (2012-2016)
Compatible Toyota Yaris models and product certifications

Figure 2: Compatible Toyota Yaris models (2012-2016) and product certifications (CE, UKCA, FC, UL).

3.2 Installation Instructions

  1. Preparation: Ensure your vehicle's engine is off and the parking brake is engaged. If possible, disconnect the vehicle's battery to prevent electrical shorts.
  2. Inspect: Before installation, check the new LED lights for any visible damage. Do not install if damaged.
  3. Remove Old Lights: Carefully remove the existing license plate light assembly from your vehicle. This usually involves unscrewing a few fasteners or prying the old unit out with a plastic trim tool.
  4. Disconnect Wiring: Disconnect the wiring harness from the old light assembly.
  5. Connect New Lights: Connect the vehicle's wiring harness directly to the new LED License Plate Light. This product is designed for direct plug-and-play installation, requiring no wiring modifications.
  6. Install New Assembly: Secure the new LED light assembly into the original housing. Ensure it clicks into place or is fastened securely.
  7. Test: Reconnect the vehicle's battery (if disconnected) and test the new lights by turning on your vehicle's lights. The LED lights should illuminate instantly with no delay.
  8. Final Check: Ensure the lights are firmly seated and functioning correctly before driving.
LED lights installed on a car, showing brightness and connector detail

Figure 3: Visual representation of the LED lights installed on a vehicle, demonstrating their brightness and the plug-and-play connector.

4. Operating Instructions

The LED License Plate Lights operate automatically with your vehicle's lighting system. When your vehicle's exterior lights are activated (e.g., headlights or parking lights), the LED license plate lights will illuminate instantly.

  • Instant Illumination: LEDs provide immediate full brightness without any warm-up time.
  • No Vehicle Function Alteration: These lights are designed to integrate seamlessly with your vehicle's existing electrical system and will not alter any other vehicle functions.

5. Maintenance

  • Cleaning: To clean the light assembly, use a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the plastic lens.
  • Inspection: Periodically check the lights for any signs of damage or loose connections.
  • Durability: The filament-free design of LED lights prevents oxidation of vehicle control circuits, contributing to their long lifespan and low maintenance requirements.
  • Waterproof: With an IP68 waterproof rating, these lights are designed to withstand various weather conditions.

6. Troubleshooting

  • Light Not Illuminating:
    • Check the electrical connection to ensure it is secure.
    • Verify that the vehicle's lights are turned on.
    • Inspect the vehicle's fuse for the license plate lights; replace if blown.
    • Ensure correct polarity if the connection allows for reversal (though typically plug-and-play prevents this).
  • Light Flickering:
    • Check for any loose connections at the wiring harness.
    • Ensure the light assembly is securely mounted.
  • Dim Light Output:
    • Ensure the lens is clean and free from dirt or debris.
    • Verify the vehicle's electrical system is providing stable 12V power.

7. Specifications

Feature Specification
Product Name Toyota LED License Plate Light
Model ATK-998
Voltage 12 V
Wattage 5 W
Color Temperature 6500 K
Material ABS+PC / LED + PC/PBT
Item Weight 0.2 kg (approx. 65 g/set)
Package Dimensions 11.5 cm × 6.4 cm × 4.5 cm
Waterproof Rating IP68
Certifications CE, ROHS, UKCA, FC, UL
Lifespan Up to 50,000 hours
Product size diagram with dimensions and performance metrics

Figure 4: Product size diagram showing dimensions (52mm, 61mm, 20mm, 15mm, 22mm) and performance metrics (8X Output, 75% Low Energy Consumption, 10X Brightness).

Detailed dimension diagram of the LED license plate light

Figure 5: Detailed dimension diagram of the LED license plate light with measurements in millimeters and inches.

8. User Tips

  • Always double-check the compatibility list to ensure these lights fit your specific Toyota model and year before purchase and installation.
  • When installing, ensure all connections are firm and secure to prevent flickering or intermittent operation.
  • After installation, perform a quick test in both daylight and low-light conditions to confirm optimal visibility.

9. Warranty & Support

For any product support, warranty claims, or technical assistance, please contact the seller or manufacturer directly.

Manufacturer Information:

Shenzhen Anyingtu Technology Co., Ltd.
Room 166, 4FA, No. 2 Trading Hall, South China City, Pinghu Street, Longgang District, Shenzhen, China

EU Authorized Representative:

PROCONSEIL FR
8 bis rue Abel 75012 Paris, France
Email: SophieDupont@proconseilfr.com

© 2024 Toyota LED License Plate Light. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.