Introduction
Thank you for choosing the Master S1000 HD Plus Digital Satellite Receiver. This manual provides essential information for the safe and proper operation, installation, and maintenance of your device. Please read it thoroughly before use.
Important Safety Instructions
Before installation and operation, please observe the following safety guidelines:
- Be sure to read this user manual before starting your operation.
- Never open the cover. It is very dangerous to touch the inside stuff of the unit due to possible electric shock.
- If you don't use this unit for a long time, please pull the power plug out from the outlet. Do not use a damaged power cord.
- Do not touch the power with wet hands. If liquid flows into the unit, pull out the power cord immediately because it may cause fire or electric shock.
- Place the unit in a well-ventilated and no-heat environment.
- You must install the dish with correct direction and angle. If the dish is not working properly, contact your local dealer.
- Install the unit horizontally. Unbalanced installation may cause the unit to be damaged.
- When the unit is suddenly moved to a hot area from a cold area, it may cause some problems. In that case, turn off the power, and turn on again after 1-2 hours.
- Install the unit in a place with:
- good ventilation
- suitable temperature
- no direct sunrays
- low humidity
- low vibration influence
- Do not put heavy objects on the unit.
General Information
The digital satellite receiver allows you to view digital satellite programs. This user's manual covers the installation of the receiver and the necessary steps to operate various features. It also explains special features available only in this receiver in detail, which will help you to take full advantage of these features.
Main Features
- Fully DVB-S/S2 compliant
- MPEG-2/MPEG-4 (H.264) SD/HD decoding (MP@MUHL)
- DISEqC1.0/1.1/1.2, USALS, Unicable and MDU supported
- USB Wi-Fi dongle supported (Ralink5370)
- Youtube/IPTV supported
- USB PVR and Timeshift supported
- Multimedia (MKV/AVI/MPG/MOV/JPG/PNG/MP3 and so on) supported
- Easy and fast software upgrade through USB/Network/OTA
- More than 5000 channels memory space
- 8 Favorite channel groups & 7 days Electronic Program Guide (EPG)
- Channel Search by automatic, manual and fastest blind scan
- Teletext output with both VBI and OSD
- Multi-language Subtitle output supported
- Multi-language and 32 bits true color on screen display (OSD) supported
- Aspect Ratio 4:3 and 16:9
- Signal level & quality indicator
- Parental Lock/Channel Lock
- Database backup to USB disk and restore from it at any time
Setup and Connection
Package Contents
The package typically includes the Master S1000 HD Plus receiver, a remote control, a power adapter, and necessary connection cables (e.g., HDMI, AV cables). Please verify all components are present upon unboxing.

Device Overview
Familiarize yourself with the front and rear panels of the receiver for proper connection and operation.

Front Panel Features
| Item | Description |
|---|---|
| USB 2.0 | For USB PVR, Timeshift, Media Player, Wi-Fi/3G Dongle |
| Buttons | 7 Buttons for basic control |
| Display | 4*7 channel display embedded |
Rear Panel Features
| Item | Description |
|---|---|
| LNB IN | For DVB-S/S2 signal input |
| USB 2.0 | For USB PVR, Timeshift and Media Player, Wi-Fi/3G Dongle |
| HD-OUT | High definition audio and video output used to connect to a HDMI device |
| VIDEO+R/L Audio | VIDEO signal output and Right/Left Audio output |
| COAXIAL | Output digital audio signal |
| DC IN | Connect the power with receiver |
| ON/OFF | Power to turn on/off the receiver |
Preparation
Read the instructions before connecting other equipment. Ensure that you observe the color-coding when connecting audio and video cables. Please connect the device with your TV by HDTV or CVBS output and set up the output format accordingly.
Operating Instructions
Remote Control
All receiver features can be controlled using the provided remote control unit.

Remote Control Button Functions
| Button | Function |
|---|---|
| 1. POWER | Standby or power on from standby. |
| 2. MUTE | Mute or restore audio output. |
| 3. RED | Red Function Key. |
| 4. GREEN | Green Function Key. |
| 5. YELLOW | Yellow Function Key. |
| 6. BLUE | Blue Function Key. |
| 7. REV | Searches backwards during media center. |
| 8. FWD | Searches forwards during media center. |
| 9. PREV | Skips to the previous track during playing media. |
| 10. NEXT | Skips to the next track during playing media. |
| 11. PLAY/PAUSE | Starts or resumes media play/pauses media play. |
| 12. STOP | During recording to stop recording. |
| 13. REPEAT/SATELLITE | Selects Sat/Repeat or turn off Sat/Repeat mode. |
| 14. LIST | To the Record Manager menu quickly. |
| 15. CC | Display Subtitle. |
| 16. TEXT | Display Teletext. |
| 17. RECALL | Used to switch between the current watching program and previous program. |
| 18. AUDIO | Selects an Audio Language or Audio Mode. |
| 19. MENU | Turns on Main Menu or back to previous menu. |
| 20. INFO | Display additional channel information. |
| 21. UP/DOWN | Move the cursor up/down. To switch among channels. |
| 22. RIGHT/LEFT | Move the cursor towards left/right. To adjust audio volume. |
| 23. OK | Confirms an entry or selection. Display the list of channels. |
| 24. EPG | (Electronic Program Guide) Turns the program guide on. |
| 25. EXIT | Exits the current Menu or returns to the previous Menu. |
| 26. Volume +/- | Increase/decrease the channel's volume. |
| 27. FAV | Turns on Favourite Menu. |
| 28. REC | Used to record the program. |
| 29. Page Up/Down | Page up/down. |
| 30. 0-9 (Numeric Buttons) | Selects a channel or setting. |
| 31. GOTO | Satellite and TP switch in Dish Setup Sub-Menu. |
| 32. TV/RADIO | To switch between TV and Radio. |
Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the receiver. Do not use liquid cleaners or abrasive materials.
- Ventilation: Ensure the unit is placed in a well-ventilated area, free from obstructions that could block airflow. Avoid placing it in enclosed spaces or near heat sources.
- Storage: If the unit will not be used for an extended period, disconnect it from the power outlet. Store it in a cool, dry place, away from direct sunlight and excessive humidity.
- Internal Access: Never attempt to open the receiver's casing. There are no user-serviceable parts inside, and doing so poses a risk of electric shock and voids any warranty.
- Weight Distribution: Avoid placing heavy objects on top of the receiver to prevent damage to its internal components or casing.
Troubleshooting
If you encounter problems with your receiver, refer to the table below for common issues and their solutions. If the problem persists, contact your local dealer or after-sales service center.
| Problem | Possible Causes | What To Do |
|---|---|---|
| No display light up on front panel | Power cord is not well plugged | Check to make sure power cord is plugged properly into power socket. |
| No sound or picture but the front panel red light is ON. | The unit is in standby mode. | Press the standby button. |
| No sound or picture. | The satellite dish is not pointing at the satellite. | Adjust the dish. Check the Signal Level in the Antenna Setup menu. |
| No signal or weak signal. | Check the cable connections, LNB and other equipment connected between the LNB and the receiver, and/or adjust the dish. | |
| Bad picture/Blocking error. | The satellite dish is not pointing at the satellite | Adjust the dish. |
| Signal is too strong. | Connect a signal attenuator to the LNB input. | |
| Satellite dish is too small. | Change to a larger dish. | |
| LNB noise factor too high. | Change to an LNB with lower noise factor. | |
| There is interference on your digital satellite channel. | The LNB is faulty. | Change the LNB. |
| The system is connected using RF cable and the output channel of the receiver interferes with an existing terrestrial channel or Video signal. | Change the receiver output channel to a more suitable channel, or connect the system using SCART cable. | |
| The RCU is not working. | Out of battery | Change the battery. |
| RCU is aimed at wrong direction. | Aim the RCU at the unit, and make sure no blocks between the front panel and RCU. |
Specifications
| Section | Item | Description |
|---|---|---|
| PROCESSOR | CPU | GX6605S |
| Flash Memory | 4MB | |
| DDR2 | 512Mb | |
| DVB-S/S2 TUNER | Input Frequency: | 950~2150MHz |
| Input level: | -80~-20dBm | |
| Input impedance | 75Ω | |
| CHANNEL DECODING | Demodulation | QPSK, 8PSK, 16PSK |
| FEC mode | DVB-S:1/2,2/3,3/4,5/6,7/8 DVB-S2:1/2,3/5,2/3,3/4,4/5,5/6,8/9,9/10 (QPSK)3/5,2/3,3/4,5/6,8/9,9/10(8PSK) | |
| Symbol Rate | DVB-S:2.0~45 MS/s | |
| Demodulation | QPSK, 8PSK, DVB-S2:10-30 Mb/s(QPSK), 10-31Mb/s(8PSK) | |
| DEMULTIPLEXER | Standard | ISO/IEC 13818-1 |
| Input Max. Bit Stream Rate | 100Mbps (Serial)/12.5MBps (Parallel) | |
| VIDEO DECODING | Standard | ISO/IEC 13818-2, MPEG-2 MP@ML, MPEG-4 AVC (MP L4.1) |
| Aspect Ratio | 4:3, 16:9 | |
| Video Format | PAL-B/NTSC-M/PAL-N/PAL-M | |
| Video Resolution | 1080P, 1080I, 720P, 480P/576P, 480/576i SD compatible | |
| AUDIO DECODING | Standard | ISO/IEC 13818-3 |
| Decoding | MPEG-1 Layer I and II, MPEG-2, MPEG-4 AAC | |
| Output Mode | LPCM, RAW | |
| Sampling Frequency | 32, 44.1, 48KHz | |
| Volume Level | 24 Levels | |
| AV OUTPUT | Video de-emphasis | CCIR REC.405-1, 625LINES |
| Video bandwidth | 5.5MHz | |
| Video output impedance | 75Ω | |
| Video output level | 1.0Vp-p | |
| Audio output | Stereo | |
| Audio output frequency | 20Hz~20KHz | |
| Audio output impedance | Low | |
| Audio output level | A 1.0Vrms+2dB into 10K. | |
| Panel Interface | • 1xAV (CVBS+R/L AUDIO) | |
| • 1x HDTV | ||
| • 1x LNB IN | ||
| • 1x IR FOR LED DISPLAY | ||
| • 2x USB 2.0 Port | ||
| OTHERS | Power input Spec. | 12V/1A DC IN Max.8W |
User Tips
- Power Adapter Compatibility: Note that the power plug of the adapter may be a European type. You might need an adapter for your region's power outlets.
- Software Upgrades: Exercise caution when performing software upgrades. Some users have reported issues with satellite signal scanning after upgrading the software. Ensure you follow official instructions carefully or consult support if issues arise.
- Check Package Contents: Upon receiving your product, carefully check that all advertised accessories, especially the remote control, are included in the package. Missing components can significantly hinder usability.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact your point of purchase or the authorized service center. Keep your purchase receipt as proof of purchase.
An additional user manual with detailed information is available in PDF format. You can access it here: Master S1000 HD Plus User Manual (PDF).