ZOYI ZTMD1/MD2

Contents

ZOYI Digital LCR Meter User Manual

1. Overview

This product is a mini digital LCR tweezers bridge. It is powered by a rechargeable lithium polymer battery for extended use and standby time. It features a TFT color display screen with a clear and intuitive interface. It intelligently identifies resistors, capacitors, and inductors, accurately measuring their values with a maximum measurement frequency of 100kHz and supports sweep frequency measurement function. In addition to traditional LCR measurement, it also features diode test, continuity test, ±32VDC voltage measurement, and a signal generator output function.

The body is small, elegant, and portable. The elastic tweezer arms paired with removable gold-plated measuring tips offer flexible and reliable operation. It is suitable for various usage scenarios such as factory SMD work, repair, teaching, and R&D.

ZOYI Tweezer LCR Meter (ZT-MD2) displaying various measurement capabilities including Rs/Rp/Cs/Cp/Ls/Lp/P/D/Q/X/Z, 0.1V-0.6V testing level, Voltage measurement, Frequency Scanning, Adjustable frequency, and CNC metal housing.

Figure 1: ZOYI Tweezer LCR Meter ZT-MD2 Features

2. Safety Precautions

To avoid possible electric shock, fire, and personal injury, please read the safety precautions before use.

  1. Do not measure voltages higher than the rated range to prevent damage to the meter and personal injury.
  2. Do not perform LCR measurements on live circuits. Ensure capacitors are fully discharged before measurement.
  3. Do not use or store this product for extended periods in high temperature, dusty environments, or under direct sunlight.
  4. Do not use this product in the presence of explosive gases, vapors, or in damp environments.

3. Setup

3.1. Package Contents

Verify that all items are present in the package. If any items are missing or damaged, contact your vendor.

Contents of the ZT-MD2 package including the red LCR tester, USB-C charging cable, a calibration board with various resistors, and a protective carrying case.

Figure 2: ZT-MD2 Package Contents

Contents of the ZT-MD1 package including the black LCR tester, USB-C charging cable, a protective carrying case, and spare test tips.

Figure 3: ZT-MD1 Package Contents

3.2. Charging the Device

The ZOYI LCR Meter supports rechargeable power and can be used while charging. It can be charged with a standard phone charger via its USB-C port.

Video 1: ZT-MD2 Unboxing and Charging Demonstration

3.3. Interface Overview

Familiarize yourself with the device's display and controls.

No.FunctionDescription
1Frequency MeasurementPress KEY4 (Frequency) to switch between different measurement frequencies.
2Level MeasurementPress KEY3 (Level) to switch between different measurement levels.
3Range/FunctionPress KEY2 (Function) to switch between different measurement functions.
4Battery StatusYellow: low battery; Lightning symbol: charging; Green: fully charged.
5Data HoldShort press KEY1 (Power) to hold current measurement value and save to record file.
6UnitDisplays the unit of the current measurement value.
7Measurement SpeedLong press KEY3 to adjust measurement speed: S=Slow, M=Medium, F=Fast.
8Measurement ModeA: Auto mode, P: Parallel equivalent mode, S: Series equivalent mode.
9Type SymbolDisplays the type symbol corresponding to the current measurement function.
10Main ValueDisplays the main measurement parameter value.
11Secondary ValueDisplays the secondary measurement parameter value.
12Secondary ValueDisplays the secondary measurement parameter value.

4. Operating Instructions

4.1. Key Operation Reference

Key NameKEY4 (Frequency)KEY3 (Level)KEY2 (Function)KEY1 (Power)
Measurement InterfaceShort: Freq Set
Long: Freq Set
Short: Speed
Long: Level
Short: Tare
Long: Function
Short: Hold
Long: Power Off
Setting InterfaceShort: Exit
Long: Cancel
Short: Up
Long: Up
Short: Down
Long: Down
Short: Confirm
Long: Power Off

4.2. LCR Measurement

  1. Press KEY2 to select the desired LCR measurement mode.
  2. Press KEY3 to choose the measurement level (typically 0.6 V).
  3. Press KEY4 to select the measurement frequency (typically 1 kHz).
  4. Place the tweezer tips across the component under test. Once the reading stabilizes, read the value displayed on the screen.

Note:

  • When measuring small resistances, ensure good surface contact. Oxidation on the surface may affect accuracy.
  • Discharge capacitors before measurement to prevent residual charge from damaging the instrument.
  • Use high frequency for small capacitors and low frequency for large capacitors; use high frequency for small inductors and low frequency for large inductors; for resistors, use 1 kHz.
  • Since the tweezer uses a two-wire measurement method, contact resistance cannot be ignored. It is recommended to use the REL (tare) function.
  • For impedances greater than 10 Ω or capacitances greater than 1 nF, calibration with REL is not necessary.
Demonstration of ZOYI LCR Meter measuring capacitance, inductance, resistance, and continuity.

Figure 4: LCR Measurement Examples

4.3. Diode and Continuity Measurement

Switch manually to the diode mode, then place the tweezer tips across the diode terminals. The screen will display the diode's polarity and forward voltage.

Note:

  • The diode symbol shown on the screen corresponds to the physical orientation of the diode under test, allowing polarity identification.
  • The forward voltage reading of the diode is for reference only. The measurement range is Vf 0.1 V-0.9 V. If the reading exceeds this range, the screen will display "OL." For higher precision requirements, use a professional diode tester.

4.4. DC Voltage Measurement

  1. Press KEY2 to switch to the voltage measurement function. The screen will display a measurement range of -32 V to +32 V.
  2. Place the tweezer tips across the voltage to be measured.
  3. Read the voltage value shown on the screen. The device will automatically determine the polarity based on the sign.

Note:

  • Do not exceed the rated input voltage range at the tweezer tips; otherwise, the device may be damaged.
  • The device cannot measure AC voltage. Do not apply AC input.
  • Do not apply voltage while in other measurement modes.
ZOYI LCR Meter measuring DC voltage of a 9V battery.

Figure 5: DC Voltage Measurement

4.5. Sweep Frequency Mode Measurement

In sweep frequency mode, the parameters of a component can be observed at different frequencies, making it convenient for analyzing the frequency characteristics of the component.

  1. Press KEY2 to switch to the sweep frequency function.
  2. Press KEY4 to select capacitance, resistance, or inductance.
  3. Place the tweezer tips across the component under test and read the parameter values displayed on the screen.

4.6. Signal Generator

The device is equipped with a signal generator output function. The available output signals include sine wave, square wave, triangle wave, staircase wave, half wave, full wave, and noise wave. The maximum frequency for sine wave is 100 kHz, while the maximum frequency for other signals is 10 kHz.

  1. Press KEY2 to switch to the signal function, then press KEY1 to confirm.
  2. Press KEY1 to select the waveform, then use KEY2 or KEY3 to choose the waveform type.
  3. Use the same method to adjust the signal frequency, amplitude, and duty cycle.
  4. Once settings are completed, the configured waveform will be output synchronously from both tweezer tips.
ZOYI LCR Meter displaying seven waveform outputs: Triangle, Noise, Full Wave, Sine Wave, Trapezoidal, PWM, and Half Wave.

Figure 6: Seven Selectable Waveforms

4.7. Sorting Mode

When measuring resistance, capacitance, or inductance, press and hold KEY2 and KEY3 simultaneously to enter the sorting measurement mode.

In sorting mode, press and hold KEY4 to set the nominal value and tolerance.

Based on the preset nominal value and tolerance, the instrument will automatically determine PASS or FAIL during measurement and record the count.

5. Calibration

When calibration is required, users can perform calibration according to the following instructions. Calibration includes the following ranges: 0 Ω, 10 Ω, 100 Ω, 1 KΩ, 10 KΩ, 100 KΩ, 1 MΩ, 10 MΩ, OPEN, and Voltage. Each range can be calibrated individually, or all ranges can be calibrated sequentially.

  1. Enter the settings menu, select the Calibration Settings option, and use KEY2 or KEY3 to choose the calibration range.
  2. Place the tweezer tips firmly across the standard source, then press KEY1 to confirm and start calibration.
  3. The calibration process takes approximately 20 seconds. Upon completion, the buzzer will sound a single "beep" and the screen will display "Success." If the calibration value is incorrect, the buzzer will sound two short "beeps" and the screen will display "Failure."

Note:

  • Use SMD carbon film resistors as calibration standards. Do not use wire-wound resistors.
  • During short-circuit calibration, ensure the tweezer tips are reliably shorted and kept as far as possible from interference sources.
  • For OPEN calibration, do not connect any resistor—keep the tweezer tips open.
  • Do not connect the charging cable or Bluetooth adapter during calibration.
  • To restore factory calibration data, simply perform a factory reset.

6. Maintenance

Do not attempt to open or repair this product, or modify the circuitry.

Clean the device with a damp cloth and mild detergent. Do not use corrosive agents or solvents.

Dust or moisture on the test ports may affect measurement accuracy.

If the tweezer tips become worn, oxidized, or damaged, they can be replaced as follows:

  1. Remove the 4 screws from the tweezer tips (screw type: 3.5PM2*3). Be sure to use matching tools.
  2. Install the new tweezer tips. Tighten the screws securely.

7. Specifications

7.1. Measurement Parameters

Main ParameterSecondary Parameter
L (Inductance)D (Loss angle tangent)
C (Capacitance)Q (Quality factor)
R (Resistance)Z (Impedance)
V (Voltage)X (Reactance)
-P (Phase angle)

7.2. Specifications Accuracy

FunctionRange100 Hz1 kHz10 kHz100 kHzAuto Range
Resistance1MΩ-10MΩ5%±55%±5--0 Ω - 10 MΩ
1KΩ-1MΩ1%±50.5%±51%±55%±5
1Ω-1KΩ1%±50.5%±51%±55%±5
0Ω-1Ω5%±55%±5--
Capacitance1mF-20mF5%±55%±5--50 pF - 5 mF
1uF-1mF2%±52%±52%±55%±5
1nF-1uF1%±50.5%±52%±55%±5
1pF-1nF2%±52%±52%±55%±5
Inductance1H-60H5%±55%±5--50 μH - 60 H
1mH-1H5%±51%±52%±55%±5
10uH-1mH0.5%±50.7%±53%±55%±5
1uH-10uH3%±53%±55%±55%±5

Voltage: Measurement Range: ±0.1 V-±32 V. Accuracy: 0.5% ± 2

Parameters: L, C, R, D, Q, Rs, Z, X, P

Functions: Auto mode, Resistance mode, Capacitance mode, Inductance mode, Diode/Continuity mode, Voltage measurement, Sweep frequency measurement, Signal output

Frequencies: 100Hz, 120Hz, 1KHz, 10KHz, 100KHz

Signal Levels: 0.1V, 0.3V, 0.6V

Signal Types: Sine wave, Square wave, Triangle wave, Staircase wave, Half wave, Full wave, Noise wave

7.3. General Technical Specifications

ParameterSpecification
Display1.47-inch TFT
RangeAuto
Sampling Rate1 time/sec
LanguagesChinese, English
Screen OrientationAuto, Left, Right
Backlight Brightness10%~100%
Volume Settings0%~100%
Auto Power OffOff, 5 min, 30 min, 60 min, 120 min
Calibration Settings0Ω-10MΩ OPEN
Low Battery WarningYes

7.4. Mechanical Specifications

ParameterSpecification
Dimensions145*29*14mm
Weight50g
BatteryLithium polymer rechargeable 3.7 V, 300 mAh
Housing MaterialCNC aluminum alloy
Warranty1 year

7.5. Environmental Conditions

ConditionTemperatureHumidity
Operating Conditions0~40℃<75%
Storage Conditions-20~60℃<80%

8. User Tips

  • Always ensure components are fully discharged before testing, especially capacitors, to prevent damage to the meter.
  • For precise measurements of small components, ensure clean contact points on both the component and the meter's tips.
  • Utilize the auto-ranging feature for general measurements, but switch to specific frequencies and levels for more detailed analysis or when encountering unstable readings.

9. Warranty and Support

9.1. Limited Warranty and Liability

This product is covered by a one-year warranty starting from the date of purchase. However, the warranty does not cover damages caused by accidents, negligence, misuse, modifications, contamination, or abnormal operating environments.

This manual is subject to change without prior notice. The information contained herein is considered accurate; if the user discovers any errors or omissions, please contact the manufacturer.

The company shall not be held responsible for any accidents or hazards resulting from improper operation by the user. The functions described in this manual are not intended as justification for using the product for special purposes.

9.2. Firmware Upgrade

With the device powered off, press and hold the KEY4 (Frequency key), then simultaneously press and hold the KEY1 (Power key) until "Bootloader" appears on the screen.

  1. Connect the device to a computer using a Type-C data cable. A USB drive will appear on the computer.
  2. Copy the prepared upgrade file into the USB drive. The upgrade will start automatically.
  3. Once completed, the screen will return to the measurement interface, indicating a successful upgrade.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.