Introduction
Thanks for purchasing the HUD. This HUD is designed to reflect your vehicle's computer information onto your windshield, offering a safer driving experience daily, especially at high speeds and during night driving. It eliminates the need for drivers to lower their heads to check the instrument cluster, helping you monitor speed more effectively and avoid speeding violations – a practical tool for both novice and experienced drivers.
The HUD adopts cutting-edge hardware and software technology, paired with a unique and elegant aesthetic design. To ensure correct setup and stable operation, please read and follow the setup steps in this manual carefully. If you encounter any problems during use, please feel free to contact our after-sales team promptly for assistance.
Main Product Features
- Plug and Play connectivity with any OBDII or EUOBD capable vehicle.
- 5.5-inch 5-color HD display, clear visuals and eye-friendly for long-time driving.
- Multi-color display layout, highlighting key data for quick and easy viewing.
- Nanotechnology applied to reduce redundant reflections, improving data readability in all light conditions.
- Real-time display of driving mileage and fuel consumption data.
- Comprehensive vehicle data monitoring: speed, engine RPM, water temperature, battery voltage, instantaneous/average fuel consumption, mileage measurement, shift reminder, fatigue driving reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code clearing, and unit switching (KM/Mile).
- Auto power on/off with the vehicle, no manual operation required.
- Dual brightness adjustment modes (automatic + manual), adaptable to various driving environments.
- Built-in CAN BUS signal protocols (ISO 1567 etc.) for Mercedes Benz M Class vehicle models.
- Read and project vehicle drive data on the windshield.
- Essential for safe driving head-up display.
Display Information Interpretation
- Light Sensor: Automatically adjusts screen brightness based on ambient light.
- Engine RPM: Real-time engine rotational speed data.
- Alarm Icon Panel (Left to Right): Shift reminder, overspeed alarm, engine fault, fatigue driving reminder, buzzer.
- Speed: Real-time vehicle driving speed.
- RPM Unit: Engine speed unit identification.
- Speed Unit Mark: KM/H (Kilometres/hour), MPH (Miles/hour), RPM (Rotations per minute).
- Engine Temperature: Real-time engine coolant temperature.
- Secondary Alarm Icon Panel (Left to Right): High temperature alarm, low voltage alarm, overspeed alarm.
- Unit Mark: °C (Celsius), °F (Fahrenheit), KM (Kilometre), V (Voltage), M (Mile).
- Multifunction Display Window: Cycles through voltage, mileage, and water temperature data.
- Fuel Consumption Unit: L/100km (Litres/100 kilometres), L/H (Litre/hour).
- Fuel Consumption Display: Real-time fuel consumption with adjustable units.
Setup and Installation
4.1 HUD Host Installation
- Confirm vehicle compatibility: Check if your car is equipped with an OBDII/EUOBD interface. Locate the 16-pin diagnostic plug under the steering wheel, consult the car manufacturer, or check for an OBDII compliance sticker under the bonnet.
- Find the OBDII interface: (usually positioned under the steering wheel), then plug the HUD OBD cable firmly into the interface.
- Start the vehicle engine: The HUD will power on automatically.
- Verify installation: If speed, RPM, voltage, and fuel consumption display normally, the installation is successful. If no data appears, wait 1 minute for system synchronization and check if the cable is securely connected.
4.2 Reflective Film Installation
Due to the double-layer structure of most car windshields, a double image may occur without the reflective film. Please follow these steps to install it properly:
- Place the non-slip mat on a flat, suitable position on the dashboard, then set the HUD on top of the mat.
- Clean and dry the target area of the windshield to ensure no dust, oil, or water stains.
- Tear off the protective layer marked (1), attach the reflective film to the preset position, and use a card to scrape out air bubbles smoothly.
- Tear off the front protective layer marked (2), adjust the HUD position via the non-slip mat to achieve the best projection effect.
Warm Tip: Install the reflective film correctly to avoid double images and ensure clear data visibility during driving.
Operating Instructions
Unit Button & Interface Functions
- OBDII Cable Input: Power supply and vehicle data transmission interface.
- Power Button: Manually turn on/off the HUD device.
- Three-way Wave Button:
- Up Button: Scroll up menus / adjust parameters upward.
- OK Button: Press inward to confirm selections / switch displayed data.
- Down Button: Scroll down menus / adjust parameters downward.
Setting Menu Operation
Most vehicles have factory data offsets, you can calibrate relevant parameters through the setting menu to match the original car dashboard data.
- Enter Setting Mode: Long press the wave button for 5 seconds.
- Parameter Adjustment: Press the OK button to switch menu pages (page number shows on the top right corner), use the up/down wave button to adjust parameter values.
- Exit Setting: Long press the wave button for 5 seconds to save settings and return to the main display interface.
Menu Parameter Table
| Menu | Parameter | Adjust Range | Explanation | Default |
|---|---|---|---|---|
| 0 | Speed | 50-150 | Speed calibration ratio | 107 |
| 1 | Rotational Speed | 50-150 | RPM calibration ratio | 117 |
| 2 | Fuel Consumption | 50-150 | Fuel consumption calibration ratio | 100 |
| 3 | RPM Alarm | 10-75 | 1000-7500 RPM alarm threshold | 25 |
| 4 | Shift Reminder | 0-75 | 1000-7500 RPM shift reminder threshold | 25 |
| 5 | Alarm Mode | 0-1 | 0=Manual, 1=Four-stage (60/80/100/120km/h) | 0 |
| 6 | Single Alarm | 30-250 | Speed alarm value (km/h) | 120 |
| 7 | Display Mode | 0-2 | 0=Auto switch, 1=Full display, 2=High-speed mode | 0 |
| 8 | Brightness | 0-2 | 0=Auto, 1=Dark, 2=Bright | 0 |
| 9 | Fuel Unit | 0-2 | 0=Hide, 1=L/H, 2=L/100km | 2 |
| 10 | Speed Unit | 0-2 | 0=RPM, 1=KM/H, 2=MPH | 1 |
| 11 | Temp Unit | 0-2 | 0=Hide, 1=°C, 2=°F | 1 |
| 12 | Mileage Unit | 0-1 | 0=KM, 1=Mile | 0 |
| 13 | Ref Fuel Consumption | 10-500 | Vehicle reference fuel consumption | 70 |
| 14 | Displacement Setting | 0-100 | Vehicle engine displacement setting | 20 |
| 15 | Start Voltage | 110-150 | Auto power on/off voltage (no adjustment needed) | 132 |
| 16 | Factory Reset | 0-1 | Set to 1, long press OK 5s to reset | 0 |
Quick Operation Tips
- Vertical press OK button: Switch displayed data (water temperature, voltage, mileage, default mode).
- Long press down wave button for 5s: Turn off the alarm buzzer.
- Long press up wave button for 5s: Turn on the alarm buzzer.
- Clear Fault Code: Turn on vehicle power (DO NOT start engine), turn off the HUD, long press down button for 5s (a tick sound indicates success) to clear fault codes.
Maintenance and Safety
Usage Notes
- Do not install the HUD in high-temperature, humid, or direct-sunlight areas to avoid device damage.
- Do not disassemble, modify, or drop the product forcibly – this will void the warranty.
- Ensure the OBD cable is firmly plugged; avoid plugging/unplugging forcibly while driving.
- Keep the device away from water, fire, and corrosive substances.
- This product is only a driving assistance tool – please always focus on safe driving and comply with local traffic rules.
Troubleshooting
| Problem | Possible Reason | Solution |
|---|---|---|
| No speed display | Alarm setting too high / function disabled | Cancel stage alarm, enable the alarm function |
| No RPM display | Setting value too high / function disabled | Reset the HUD, enable related functions |
| No display after startup | Power off / loose cable connection | Turn on power, check and tighten the OBD cable |
| Inaccurate fuel consumption display | No air flow sensor equipped | Reset displacement setting, recalibrate fuel consumption |
| No speed/RPM data | Vehicle OBDII/EUOBD incompatible | Confirm vehicle interface compatibility |
| Inaccurate speed reading | Speed unit set to MPH | Switch speed unit to KM/H in the menu |
| Only speed & fuel displayed | Speed over 80km/h (high-speed mode activated) | Enter settings, switch display mode to 1 |
Specifications
| Parameter | Value |
|---|---|
| Operating Temperature | -40°C ~ +80°C |
| Barometric Pressure | 86-106KPa |
| Relative Humidity | 10%-95% |
| Ambient Noise | ≤60dB |
| Alarm Sound Level | ≥30dB(A) |
| Working Voltage | 9V~16Vdc (12Vdc/400mA) |
| Product Size | 12.5*7.5*1.5cm |
| Product Weight | 110g |
| Speed Type | OBD vehicle speed, GPS speed |
| Output Frequency | About 45Hz |
| Rated Power | About 5W |
| Size Name | 5.5 inch wide screen projection |
| Wire or Wireless | OBD-II, EU-OBD |
Warranty and Support
Warranty Policy
This product comes with a 12-month warranty from the date of receipt. We provide free replacement or repair for non-human quality issues, with round-trip shipping fees borne by the seller. Damage caused by man-made faults, improper use, unauthorized disassembly, or natural disasters is not covered by the warranty. For after-sales support, please contact us with your order information and detailed fault description.
For further assistance, you may refer to the official user manual PDF: View User Manual (PDF)
Product Overview and Demonstration