1. Important Safety Information
⚠ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
Always perform a safety check before each ride. Ensure all components are securely fastened and functioning correctly.
- Wear a helmet and appropriate safety gear.
- Obey all local traffic laws and regulations.
- Do not operate the e-bike under the influence of alcohol or drugs.
- Be aware of your surroundings and ride defensively.
- Do not modify the e-bike's electrical system or components.
- Keep hands and feet away from moving parts.
2. Product Overview and Specifications
The Thunder 02-1 is a 7-speed city electric bicycle designed for adult use, featuring a powerful Bafang rear hub motor and a durable aluminum alloy frame.

Figure 1: Thunder 02-1 Electric Bicycle
2.1 Key Features
- Motor: 48V 500W Bafang Rear Hub Motor
- Battery: 48V 12Ah Lithium Battery
- Frame: 6061 Aluminum Alloy
- Gears: Shimano 7-Speed
- Brakes: Front and Rear Mechanical Disc Brakes
- Suspension: MOZO/EXSHO Front Suspension Forks
- Tires: 26''x1.95 Kenda Tires
- Display: SW-900 LCD Display
- Accessories: Headlight, Rear Light, Rear Rack
2.2 Technical Specifications
| Attribute | Specification |
|---|---|
| Model Number | 02-1 |
| Certification | CE |
| Rated Passenger Capacity | One Seat |
| Max Speed | 25-42 km/h (15.5-26 mph) |
| Wattage | 500W |
| Voltage | 48V |
| Power Source | Lithium Battery |
| Range per Charge | 30-50 km (18-31 miles) |
| Max Load | 150 kg (330 lbs) |
| Charging Time | 4-6 Hours |
| Foldable | No |
| Color | Black |
2.3 Package Contents
Upon unpacking, ensure all components are present:
- Thunder 02-1 Electric Bicycle (partially assembled)
- 48V 12Ah Lithium Battery
- Battery Charger
- Pedals (left and right)
- Tool Kit (for assembly)
- User Manual (this document, or refer to PDF)
For a detailed visual guide, please refer to the complete user manual PDF available at this link.
3. Assembly Instructions
Your e-bike comes partially assembled. Follow these steps carefully to complete the assembly.
3.1 Installing the Front Wheel
- Remove the shipping spacer, bolt, and nut from the front wheel fork.
- Remove the spacer between the front disc brake caliper. Do not squeeze the front brake handle as this may cause the pads to move, making disc insertion difficult.
- Insert the axle into the front wheel hub. Position the front wheel between the forks while carefully aligning the front brake disc into the brake caliper.
- Place a washer onto the axle on the outside of the forks.
- Install and hand-tighten the two adjustment nuts equally. Use the supplied 15mm socket wrench and 15mm wrench to finish tightening, ensuring equal tightness on both sides.
- The adjustment nuts must be very tight. Retighten them after your first two rides.
- Inspect that your front wheel is securely properly before every ride.

Figure 2: Front Wheel and Fork Assembly
⚠ WARNING: The front wheel must be inspected before every ride to ensure it is securely attached. Failure to do so could result in significant injury or death.
3.2 Installing the Handlebars
- Ensure the fork and headset are pointing towards the front of the bike.
- Center the handlebar in the headset, taking care not to damage any wires.
- Install the clamp and screws. Alternately tighten the screws side-to-side until secure.
- Verify the headset and handlebar are lined up. You will re-adjust after installing the front wheel.
- Verify that all headset items are tight.
3.3 Installing the Pedals
⚠ NOTICE: It's critical that the pedals are tightened firmly in the crank arm to prevent loosening while riding, which can cause significant damage.
- Identify the left ("L") and right ("R") markings on the pedals.
- Install the "L" pedal on the left crank arm and the "R" pedal on the right crank arm (chain side). Both pedals tighten towards the front of the e-bike.
- While keeping the pedal horizontal, carefully hand-start the threads into the crank arm.
- Finish tightening the pedals using the supplied 15mm wrench. The pedals must be very tight. Check and retighten after your first two rides.
3.4 Adjusting Seat Height
- Loosen the seat post clamp.
- Adjust the seat to a comfortable height, ensuring the minimum insertion length mark on the seatpost remains inside the seat tube.
- Tighten the seat post clamp securely.
4. Operation
4.1 Initial Ride Preparation
Before your first ride, ensure all installed items are properly torqued, tightened, and connected. Users can ride the e-bike like a normal bicycle with power ON or OFF. Pedal assist and throttle activate only when power is ON.
We recommend riding with pedal assist off initially to familiarize yourself with braking and gear shifting. Then, incrementally test pedal assist levels.
4.2 Safety Check Before Each Ride
- Battery pack is charged and secured.
- Keys are removed from the battery pack.
- Display turns on and functions properly.
- Brakes function properly.
- Tires are inflated to proper PSI.
- Front and rear lights work properly.
- Cable connections are tight.
- Wheels are secured and spokes are tight.
4.3 Using the Brakes
The e-bike is equipped with front and rear disc brakes. Apply the rear brake before the front brake in low-traction conditions.
- Front Brake: Controlled by the left-hand lever. Provides the majority of stopping power.
- Rear Brake: Controlled by the right-hand lever.
- A signal wire from each brake lever automatically turns off the motor when engaged, preventing undue wear.
- New brakes require a "bedding-in" period (40-50 full stops) to reach full grip capacity. Adjust levers as needed.
4.4 Pedal Assist Control System (Pedelec)
The system uses cadence sensors to measure pedaling, transferring information to the controller to generate power and maintain a constant level of pedal assist.
- Before installing the battery pack, press the battery power button to turn it on. The LED will illuminate blue, showing current charge status.
- Install the battery pack onto the bike, ensuring it's locked securely and keys are removed.
- Press and hold the LED display mode button for 3 seconds to turn on the bike. The display will show battery charge and selected pedal assist level.
- Pushing the Mode button cycles pedal assist from P0 to P4 and back to P0.
- When moving, the display switches from Pedal Assist Mode to current speed, returning to assist level when stopped.
Basic LED Modes:
- P0: No assist, throttle only.
- P1, P2, P3, P4: Power output levels (all modes have a max speed of 20mph).
Advanced LCD Modes:
- 0: Throttle Operation Only
- ECO: Battery Efficiency
- 1, 2, 3: Speed Ranges
- S: Sport
- R: Race Track Mode (refer to local laws & regulations)
4.5 Throttle Operation
The throttle control is on the right-side handlebar. It can be used with or without pedal assist.
- Turn on the battery and LED/LCD display.
- Set the display to the desired setting (P0 disables pedal assist).
- Rotate the throttle to increase speed.
4.6 Reading the Battery Pack Level
The LED/LCD display indicates battery voltage, which can vary. Voltage temporarily decreases with throttle/pedal assist use or uphill riding. Cold environments also lower voltage.
- 2 Bars: Recharge soon, select lower pedal assist.
- 1 Bar: Stop using throttle, recharge.

Figure 3: Battery Pack on the E-Bike
4.7 Understanding Battery Pack Range
Riding range varies greatly. Factors that decrease range include:
- Rapid accelerations
- Uphill riding
- Heavy payloads
- Headwinds
- Underinflated tires
- Extreme hot or cold weather
To increase range:
- Pedal instead of only using the motor.
- Avoid rapid accelerations.
- Pedal to assist motor on steep hills, use gears.
- Reduce average pedal assist level.
- Reduce payload weight.
- Properly inflate tires (30-35 psi).
- Coast to stops, avoid rapid decelerations.
4.8 Turning the E-Bike On and Off
To Turn On (LED Display):
Press battery power button, install battery, then push and hold mode button for 3 seconds. Display illuminates.
To Turn Off (LED Display):
Push and hold mode button for 3 seconds. Display powers down. No need to turn off battery separately.
To Turn On (LCD Display):
Press battery power button, install battery, then push and hold the power button on the back of the LCD for 3 seconds. Display illuminates.
To Turn Off (LCD Display):
Push and hold the power button on the back of the LCD for 3 seconds. Display powers down.
Automatic Shutoff: The electronic system will automatically shut down after a preset period of inactivity.
4.9 Adjusting Assist Levels
To Increase (LED Display):
Push and release the mode button. Assist advances one level until P4.
To Decrease (LED Display):
Cycle through modes to return to a lower level.
To Increase (LCD Display):
Push and release the "assist up" button. Assist advances one level until SPORT mode.
To Decrease (LCD Display):
Push and release the "assist down" button. Assist decreases one level until ECO mode.
4.10 Activating Headlight and Display Backlight
To Turn On (LED Display):
Press the mode button twice quickly. Headlight comes on, icon appears.
To Turn Off (LED Display):
Press the mode button twice quickly.
To Turn On (LCD Display):
Push and hold the "assist up" button for 2 seconds. Front LED headlight and display backlight illuminate, icon appears.
To Turn Off (LCD Display):
Push and hold the "assist up" button for 2 seconds.
4.11 Walk Mode (Advanced LCD)
Assists when pushing the bike uphill at walking speed.
To Activate:
Push and hold the "assist down" button. Motor starts after 2 seconds.
To Stop:
Release "assist down" button, or use either brake lever.
4.12 Cruise Control Function (Advanced LCD)
Maintains desired speed without throttle or pedal assist.
To Activate:
Reach desired speed with throttle/pedal assist. Push and hold "assist down" button for 2 seconds. Release when "C" graphic appears. Speed is maintained.
To Discontinue:
Use brakes, use throttle, or push "assist up" or "assist down" button.
Important Notes: Cruise is a type of throttle, max 20 mph. Pedal assist is still available. Keep eyes on road, hands on handlebars.
4.13 Resetting the Trip Counter (Advanced LCD)
Resets trip distance, Amp-hours (Ah), and Watt-hour (Wh) data.
To Reset:
Push and hold both the power button and "assist down" button for 3 seconds, then release.
4.14 Advanced Display Screen (Advanced LCD)
Shows expanded real-time data: Voltage, Power, Amps, Assist Level, Speed, Watt-hours, Amp-hours, Controller Temperature, Trip Distance.
To Toggle:
Push the power button and "assist up" button at the same time for 1 second.
4.15 Adjusting Parameters in the Setup Menu (Advanced LCD)
Controls e-bike behavior.
To Enter Menu:
Hold "assist up" and "assist down" buttons for 3 seconds, then release.
Navigating and Adjusting:
Use "assist up"/"assist down" to navigate. Push power button to enter setting. Adjust with "assist up"/"assist down". Push power button to exit setting. Continue until main screen.
Available Menu Options:
- Unit: mph or km/h.
- Speed Limit: Sets max speed. (Refer to manual for classification table).
- Backlight: Brightness.
- Wheel Size: Tire circumference in mm.
- "Power Off" Delay: Duration of inactivity before auto-shutdown.
- NDW (Pedal Assist Level Limiter): Adjusts max pedal assist level (ECO, 1, 2, 3, SPORT, RACE).
- Torque: Use torque sensor for pedal assist (ON/OFF).
- Low Volts: Controls battery discharge depth.
5. Maintenance
5.1 Battery Care and Charging
⚠ NOTICE: Recharge the battery pack at least once every month. A battery pack left unused for several months may result in permanent capacity loss.
Battery Safety Guidelines:
- Do not short-circuit terminals.
- Do not charge if temperature is over 140°F (60°C).
- Do not disassemble.
- Do not submerge in liquid or use in wet areas.
- Do not place near fire or heat.
- Do not expose to freezing temperatures; do not charge a frozen pack.
The e-bike uses a high-capacity lithium-ion battery with 500-700 full charge cycles. Always charge before a long trip. The onboard circuit prevents overcharging.
Onboard Charging Procedure:
- Stand on the left side, locate charge port dust cover on top of battery pack.
- Rotate dust cover to expose DC charge port.
- Carefully plug charger into charge port.
- Connect AC power cable to charger and then to power outlet.
- Indicator LED will be red during charging, green when fully charged. Charging takes 1-8 hours.
- Disconnect charger from wall, then from DC charge port. Rotate dust cover to protect port.

Figure 4: Rear Wheel and Motor Assembly
5.2 Hydraulic Brakes
Inspect and service hydraulic brakes regularly for wear and tear. Replacement may be needed based on riding time, mileage, style, and location. Inspect brakes before every ride.
⚠ Notice: If any issue appears with your braking system, do not use your bike and contact support or an authorized mechanic.
5.3 Mineral Oil Cups
Have a trained mechanic service the mineral oil cups on the handlebars.
6. Troubleshooting
This section addresses common issues you might encounter with your electric bicycle.
| Problem | Possible Cause | Solution |
|---|---|---|
| E-bike does not power on | Battery not charged, battery not properly installed, power button not pressed correctly. | Charge battery, ensure battery is fully seated and locked, press power button firmly for 3 seconds. |
| Motor not assisting | Pedal assist level is P0, brake levers engaged, battery low, loose motor cable. | Increase pedal assist level, release brake levers, charge battery, check motor cable connections. |
| Short battery range | Factors listed in Section 4.7 (uphill, heavy load, low tire pressure, etc.). | Review Section 4.7 for tips to increase range. Ensure tires are properly inflated. |
| Brakes feel weak or noisy | New brakes (bedding-in period), worn brake pads, disc rotor contamination. | Allow for bedding-in period. Inspect brake pads for wear and replace if necessary. Clean disc rotors with isopropyl alcohol. |
| Display not working | Loose display cable, battery low, display damaged. | Check display cable connections. Charge battery. If issue persists, contact support. |
For issues not covered here, please consult the full PDF manual or contact customer support.
7. User Tips
- Regular Checks: Make it a habit to quickly check tire pressure, brake function, and battery charge before every ride.
- Gear Shifting: Shift gears proactively, especially before inclines, to reduce strain on the motor and battery.
- Battery Longevity: Avoid fully draining the battery regularly. Charge it after each significant ride, and at least once a month during storage.
- Smooth Riding: Accelerate and brake smoothly to conserve battery life and reduce wear on components.
- Secure Parking: Always lock your e-bike when leaving it unattended, and consider removing the battery for added security.
8. Warranty and Support
For warranty information, please refer to the terms and conditions provided at the time of purchase or contact your seller directly. Keep your proof of purchase for any warranty claims.
If you encounter any problems or have questions about your Thunder 02-1 Electric Bicycle, please contact the retailer or manufacturer's customer support for assistance.
Full User Manual: A comprehensive user manual in PDF format is available for download: Download PDF Manual