1. Introduction
This digital temperature controller is designed for precise temperature management in various applications such as incubation, breeding, industrial heating, and cooling. It features WiFi connectivity for smart control, allowing users to monitor and adjust settings remotely. The device supports a wide temperature range from -40°C to 99°C.
2. Safety Information
Warning: Before installation, wiring, or maintenance, read this manual carefully. Incorrect operation may lead to equipment damage, fire, or personal injury.
- Power Disconnection: All wiring changes must be performed with the power disconnected. Never work with live power.
- Voltage Matching: The supply voltage must match the voltage specified on the thermostat's nameplate (AC 110-230V) and ensure a stable power supply.
- Anti-interference Wiring: To avoid potential interference, keep sensor wires and power lines appropriately separated and do not bundle them in parallel.
- Wiring Distinction: Strictly distinguish between sensor wires, power wires, and output relay interfaces. Avoid incorrect connections.
- Load Limit: Relays must not be overloaded. The cooling/heating output capacity is 10A/250VAC. Do not exceed this limit.
3. Setup
3.1. Installation
For panel mounting, open a corresponding size mounting hole on the control panel according to the product dimensions. Then, embed and securely fix the controller into the hole.
3.2. Wiring Steps
- Ensure the power supply is completely disconnected before proceeding with any wiring.
- Refer to the connection diagram below (Figure 4) to connect the power lines, sensor lines, and load lines (e.g., compressor for refrigeration, heating elements for heating) separately.
- Important: Ensure the sensor type matches the specific model of your controller. The DTC2201 model uses a DS18B20 sensor, while the DTC1201 model uses an NTC sensor.
- After completing all wiring, carefully check for any short circuits or incorrect connections. Only power on the device after confirming everything is correctly wired and secure.
4. Operating Instructions
The Tuya WiFi Digit Temperature Controller allows for intelligent temperature control for both heating and cooling applications. Once powered on and connected to your WiFi network, you can set the desired temperature range and operating mode (heating or cooling) directly on the device or via the Tuya smart application.
The display shows the current temperature, and indicators for 'Cool', 'Set', 'Heat', and 'Net' provide status information. Use the 'S' button to enter settings mode and the up/down arrows to adjust values. Refer to the specific Tuya app instructions for remote control and advanced scheduling features.
5. Specifications
| Item | Parameter |
|---|---|
| Product Name | Digital Temperature Controller (Thermostat) |
| Product Model | DTC2201 / DTC1201 |
| Supply Voltage | AC 110-230V |
| Temperature Range | -40°C ~ 99°C |
| Measurement Accuracy | ±1°C (-40°C ~ 70°C) |
| Sensor Cable Length | 100cm |
| Sensor Type | DS18B20 (DTC2201) / NTC (DTC1201) |
| Product Dimensions | 93mm × 56mm × 85mm |
| Output Capacity | Refrigeration: 10A/250VAC; Heating: 10A/250VAC |
6. Maintenance
- This device is for indoor use only. Avoid use in humid, corrosive gas, or strong magnetic field environments.
- The sensor probe cannot withstand extreme temperatures beyond its rated range. Ensure it is used within its specified operating conditions.
- Non-professionals should not disassemble the casing to avoid electric shock or damage to precision components.
- Keep the device clean and free from dust to ensure optimal performance and longevity.
7. Troubleshooting
If the device exhibits abnormal behavior, such as displaying incorrect error codes or being unable to control the temperature as expected, please follow these steps:
- Immediately disconnect the power supply to the device.
- Check all wiring connections for looseness or incorrect placement, referring to the connection diagram in Section 3.2.
- If the issue persists after checking connections, contact customer service for further assistance.
8. User Tips
No specific user tips were available from reviews or Q&A for this product at this time. Always ensure proper ventilation around the device and its connected loads for optimal performance.
9. Compliance
This product complies with CE standards.
CE
10. Warranty & Support
For further assistance, technical support, or warranty information, please refer to the official product documentation provided by the manufacturer or contact the seller directly.
A detailed user manual (PDF) is available for download: User Manual (PDF).