Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your 12V 6 LED License Plate Light. Designed for universal fit, this light enhances visibility and safety across various vehicles including trucks, SUVs, trailers, vans, boats, RVs, and motorcycles. Please read all instructions carefully before use to ensure proper function and safety.
Important Safety Information
- Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Do not exceed the recommended torque during installation.
- Keep the product out of reach of children.
- Do not use this product for purposes other than its intended use.
- Inspect the product for damage before each use; do not use if damaged.
- Avoid exposure to extreme temperatures (e.g., high heat or freezing conditions).
Product Features
- Super bright 6 LED xenon white light for maximum visibility and safety.
- Color Temperature: 6000K.
- Universal fit for 12V systems in boats, cars, trucks, trailers, RVs, and motorcycles.
- Long lifespan and low power consumption.
- Easy to install with direct bolt-on design and shock resistance.
- Circuit board completely sealed by epoxy for waterproof performance.
- Can be used as license plate light, step light, or door light.
- High-quality construction for durability.
Specifications
| Attribute | Value |
|---|---|
| Device Type | LED License Plate Light |
| Light Source | 6 LEDs |
| Body Color | Black |
| Light Color | White |
| Color Temperature | 6000K |
| Material | PC |
| Voltage | 12V |
| Wattage | 1.8W |
| Current | 0.3A |
| Connection | 2 Wires |
| Dimensions (L x W x H) | 2.6 x 1.3 x 0.87 inches |
| Fitment | 12V systems in boats, aircraft, automotive, RV, motorcycles, trucks |
| Function | License Plate Light, Step Light, Door Light |
Figure 1: Product Dimensions
Setup and Installation
Before first use, ensure the product is free from debris or defects. The light is designed for direct bolt-on installation.
Package Contents:
- 1 or 2 x LED License Plate Light(s) (depending on purchase)
- 2 or 4 x Screws (depending on purchase)
Figure 2: Package Contents (1-piece and 2-piece options)
Wiring Instructions:
- Identify the positive and negative wires from your vehicle's 12V power source.
- Connect the Red wire from the LED light to the vehicle's Positive (+) terminal.
- Connect the Black wire from the LED light to the vehicle's Negative (-) terminal.
- Ensure all connections are secure and insulated to prevent short circuits.
Figure 3: Wiring Diagram
Mounting:
- Choose a suitable flat surface for mounting the light.
- Align the light and mark the positions for the mounting screws.
- Drill pilot holes if necessary, ensuring they are appropriate for the provided screws.
- Secure the light in place using the provided screws. Do not overtighten.
Operation
Once properly installed and wired, the LED license plate light will illuminate when power is supplied to its circuit (e.g., when vehicle lights are turned on, or when a door is opened if used as a door light). The 6000K white light provides clear and bright illumination.
Figure 4: Lighting Effect
Figure 5: Installed Lighting Effect on Vehicle
Maintenance
- Cleaning: Wipe the light's surface with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the PC material.
- Inspection: Periodically check the wiring connections for any signs of wear, corrosion, or looseness. Ensure the mounting screws are still secure.
- Waterproof Seal: The circuit board is epoxy-sealed for waterproofing. Avoid tampering with this seal.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power supply; incorrect wiring; loose connection; damaged light. | Check vehicle's power source (e.g., fuse); verify red wire to positive and black to negative; secure all connections; inspect light for damage. |
| Light flickers | Loose wiring connection; unstable power supply. | Check and secure all wiring connections; ensure stable 12V power. |
| Water inside the light | Compromised waterproof seal; improper installation. | Ensure proper mounting and that no water can seep in from edges. If the internal seal is compromised, the unit may need replacement. |
User Tips
- Always double-check your vehicle's wiring diagram before making electrical connections to avoid damage to the light or vehicle.
- Consider using dielectric grease on electrical connections for added protection against moisture and corrosion, especially in marine or harsh environments.
Compliance & Manufacturer Information
Compliance Information:
- This product complies with the EU RoHS 2.0 Directive (2011/65/EU) and REACH Regulation (EC) No 1907/2006.
- It bears the CE marking and conforms to the ISO 9001:2015 quality management standard.
Manufacturer:
Company Name: Shanghai Xianyu Electronic Commerce Co.,LTD
Address: Room 30506, Building 14, No.3265 Jinhai Road, Fengxian District, Shanghai 201400
Telephone: 86-18355901613
E-Mail: vkojvoivn@outlook.com
EU Authorized Representative:
Company Name: SINO-SEAR GmbH
Address: Feuerbachstrasse 11, 14471 Potsdam, Germany
Telephone: +49 331 95130908
E-Mail: info@sino-sear.com