1. Safety Information
Please read all safety instructions carefully before using the device to prevent damage and ensure proper operation.
1.1 Electrical Safety
- Do not operate the power switch or plug/unplug the power cord with wet hands.
- Use only the original DC 52V/2.3A power adapter. Non-standard power supplies may cause damage.
- Install professional lightning arresters in areas prone to frequent lightning.
1.2 Physical Protection
- Do not place liquid containers on the device to prevent short circuits or fire.
- Avoid direct sunlight or strong light, which may affect screen display.
- Keep the device ventilation holes clean. Regular cleaning (monthly) is recommended.
2. Setup and Installation
2.1 Package Contents
Before proceeding, please verify that all items are included in your package:

Image: SriHome NVS005 NVR Packing List. Shows the NVR unit, power supply, USB mouse, network cable, HDD mounting screws, and user manual.
- 1 x 8-channel PoE Recorder (NVS005)
- 1 x NVR Power Supply (DC 52V/2.3A)
- 1 x USB Mouse
- 1 x Network Cable
- 1 x Set of HDD Mounting Screws
- 1 x User Manual
2.2 NVR Overview and Ports
Familiarize yourself with the NVR's physical layout and connection ports.

Image: Front and rear view of the SriHome NVS005 8CH PoE NVR. The front panel shows the SriHome logo and NVR branding. The rear panel displays all connection ports.

Image: Product description of SriHome NVS005 NVR with dimensions (247mm/9.72in length, 45mm/1.77in height, 256mm/10.08in width) and labeled ports: Power Port, PoE Ports, LAN Port, Audio Output Port, VGA Port, HDMI Port, USB Port.
Rear Panel Ports:
- DC 52V/2.3A Power Input: For connecting the NVR power supply.
- PoE Ports (PoE1-PoE8): 8 ports for connecting PoE cameras, providing both power and data.
- LAN Port: For connecting the NVR to your router/network.
- A-OUT (Audio Output): For connecting external speakers.
- HD-OUT (HDMI Output): For connecting to an HDMI-compatible monitor or TV.
- VGA: For connecting to a VGA-compatible monitor.
- USB Ports: For connecting the USB mouse or external storage devices.
2.3 Camera Installation Method
Cameras can be installed either wall-mounted or ceiling-mounted. Choose the method suitable for your environment.
- Wooden Wall Installation: No drilling is required. Use an electric drill or screwdriver with screws to fix the camera directly.
- Concrete Wall Installation: Drill two holes with a diameter of 6mm and a depth of 25-35mm. Insert green expansion bolts with a hammer. Then, use an electric drill or screwdriver to securely fix the camera.
2.4 NVR Connection
Follow these steps to connect your NVR system:

Image: Network connection diagram for SriHome NVS005 NVR. Shows PoE cameras connecting to NVR PoE ports, NVR LAN port connecting to a router, and NVR HDMI/VGA output connecting to a monitor. USB mouse and power supply are also shown.
- Connect PoE cameras to the NVR's PoE ports using Ethernet cables.
- Connect the NVR's LAN port to your router using an Ethernet cable (do not use a PoE port for this).
- Plug the DC power supply into the NVR's power input, then plug it into a power outlet. Use only the standard 48V-56V power supply.
- Connect the NVR to a monitor using an HDMI or VGA cable.
- After powering on, the camera images should automatically display on the monitor. The default password is 888888.
2.5 Hard Disk Drive (HDD) Installation
If your NVR did not come with a pre-installed HDD, you will need to install one for recording. The NVR supports a 3.5-inch SATA mechanical hard drive, with a maximum capacity of 16TB per single drive. Surveillance-grade HDDs are recommended.
Important: Disconnect the power supply and wait at least 5 minutes before installation to prevent hardware damage.
- Loosen the screws on the NVR's rear and side panels.
- Remove the NVR cover.
- If an insulating sheet is on the battery, remove it first.
- Insert the hard drive with a SATA interface into the designated slot.
- Connect the SATA data cable and power cable to the HDD.
- Fasten the screws on the bottom to secure the HDD.
- Re-install the NVR cover and fasten the screws.
2.6 Adding a PoE Camera
Method 1: Automatic Configuration
- Connect the NVR host directly to the PoE camera using a standard network cable (Cat5e/Cat6).
- Ensure the NVR is connected to the router (for automatic IP address assignment).
- Verify that the switch/PoE port indicator is green (normal power supply).
- The device should automatically complete configuration within 30 seconds, and the camera's real-time image will appear on the NVR preview interface.
- If no image appears, click the '+' icon in the lower left corner of the surveillance monitor, open the screen for adding a camera, and enable the 'Automatically add IPC' switch.
Method 2: Add via LAN (Onvif Network Protocol Camera)
This method allows adding SriHome wired network cameras (up to 5MP) supporting Onvif protocol.
- Connect the camera to the same router/switch as the NVR host via an Ethernet cable.
- In the NVR's 'add camera' interface, select 'Add' to scan for devices in the LAN.
- Double-click the desired camera from the list of available devices.
- Enter the camera's password (default is 888888) in the pop-up interface and confirm.
2.7 APP Installation
To use the mobile application for remote viewing and control:
- Method 1: Scan the QR code provided in the manual (or on the product packaging) to download the