KNOA S-360W/400W/500W

Contents

KNOA LED Transformer Power Adapter User Manual

Models: S-360W, S-400W, S-500W

1. Introduction

This manual provides essential information for the safe and efficient operation of your KNOA LED Transformer Power Adapter. Please read this manual thoroughly before installation and use, and keep it for future reference.

Product Information

  • Product Name: Switching Power Supply
  • Brand: KNOA
  • Model Numbers: S-360W, S-400W, S-500W
  • Type: AC to DC Power Supply
  • Output Power: 360W, 400W, 500W (depending on model)
  • Output Voltage Options: 12V, 24V, 36V, 48V DC

2. Safety Warnings and Precautions

Failure to follow these instructions may result in damage to the product, personal injury, or electric shock. Always exercise caution when working with electrical devices.

  • High Voltage Danger: This product operates with high voltage. Installation and wiring should only be performed by qualified personnel.
  • Children: Keep the device and its cord out of reach of children under 3 years old. Keep away from children unless supervised by an adult.
  • Intended Use: Do not use this product for purposes other than its intended use as an AC to DC power supply.
  • Inspection: Inspect the product before each use. Do not use if damaged.
  • Environment: Do not expose to water, moisture, or highly humid environments. Ensure adequate ventilation around the unit to prevent overheating.
  • Ventilation: Do not block ventilation openings.
  • Handling: Handle with care to avoid cuts or injuries from sharp edges.
  • Input Voltage: Ensure the input voltage selector switch is set correctly for your region's AC supply (110V or 220V) before connecting power. Incorrect setting will damage the unit.

3. Setup and Installation

3.1 Unpacking

Carefully remove the power supply from its packaging. Inspect for any visible damage. If damaged, do not use and contact support.

3.2 Input Voltage Selection

CRITICAL STEP: Before connecting any power, verify and set the input voltage switch located on the side of the unit to match your local AC mains voltage (110V or 220V).

Input voltage selector switch set to 110V or 220V

Figure 1: Input Voltage Selector Switch. Ensure it is set correctly for your region (e.g., 110V for USA).

For users in the United States, set the switch to 110V. Incorrect setting will cause irreparable damage to the power supply.

3.3 Wiring Connections

Wire the power supply correctly according to the product diagram. Due to high voltage, professional operation is required.

Product show with terminal block details

Figure 2: Product views showing terminal block for wiring.

  • AC Input (Left Terminal Block):
    • Connect your AC Live wire to the 'L' terminal.
    • Connect your AC Neutral wire to the 'N' terminal.
    • Connect your Earth Ground wire to the 'GND' or '⏚' terminal.
  • DC Output (Right Terminal Block):
    • Connect your positive DC load wire to the 'V+' terminals.
    • Connect your negative DC load wire to the 'V-' terminals.
    • This unit features three sets of output channels (V+ and V-) to power multiple electronic devices.

Ensure all connections are secure and properly insulated to prevent short circuits.

3.4 Mounting

The power supply can be mounted using the provided mounting holes. Ensure the mounting location allows for adequate airflow around the unit for proper heat dissipation.

4. Operating Instructions

Once properly wired and the input voltage selected, the power supply is ready for operation.

  1. Double-check all wiring connections and the input voltage selector switch.
  2. Apply AC power to the input terminals.
  3. The power supply will convert the AC input to the specified DC output voltage.
  4. Cooling Fan Operation: The built-in cooling fan is temperature-controlled. It will not run continuously but will activate only when the internal temperature reaches approximately 113°F (45°C) to ensure efficient heat dissipation.

Protection Features

This power supply is equipped with multiple safety protection systems:

Icons for Overvoltage, Overload, Overtemperature, Short-circuit protection

Figure 3: Built-in Protection Features.

  • Overvoltage Protection: Protects connected devices from excessive output voltage.
  • Overload Protection: Automatically cuts off power if the output current exceeds safe limits.
  • Overtemperature Protection: Shuts down the unit if internal temperatures become too high.
  • Short-circuit Protection: Prevents damage in case of a short circuit in the output.

5. Maintenance

The KNOA Power Adapter is designed for reliable operation with minimal maintenance.

  • Cleaning: Keep the unit clean and free from dust. Use a dry, soft cloth to wipe the exterior. Do not use liquid cleaners.
  • Ventilation: Ensure that the ventilation openings are not obstructed by dust or debris. Periodically check for any blockages.
  • Storage: When not in use, store the device in a dry place, away from direct sunlight and extreme temperatures.

6. Troubleshooting

If the power supply is not functioning as expected, perform the following checks:

ProblemPossible CauseSolution
No output voltageNo AC input power
Incorrect input voltage switch setting
Short circuit or overload on output
Internal fault
Check AC power source and connections
Verify input voltage switch (110V/220V) is correct
Disconnect load and check for short circuits; reduce load
Contact support
Output voltage is unstableLoose connections
Overload
Faulty load
Check all wiring connections
Reduce load
Test with a different load
Unit is overheatingInsufficient ventilation
Overload
Ensure adequate airflow around the unit; clear obstructions
Reduce load
Cooling fan not runningNormal operation (temperature below threshold)The fan activates only when internal temperature reaches ~113°F (45°C). This is normal.

If troubleshooting steps do not resolve the issue, do not attempt to repair the unit yourself. Contact customer support.

7. Specifications

KNOA 400W Power Supply with dimensions and input/output details

Figure 4: Product overview with key specifications.

FeatureSpecification
Brand NameKNOA
Model NumberS-360W/400W/500W
TypePower Supply
Input Voltage100-120V AC / 200-240V AC (selectable via switch)
Output Voltage12V, 24V, 36V, 48V DC (model dependent)
Output Power150-500W (e.g., 360W, 400W, 500W)
Output Current0-50A (model dependent)
Output Frequency47-63Hz (input frequency)
Output TypeSINGLE
Rated Capacity40-1000VA
Dimensions (Approx.)215mm x 115mm x 50mm (L x W x H)
Package Weight (Approx.)0.837 kg
CertificationsCE, FCC, RoHS
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc

8. User Tips

  • Normal Heat: It is normal for the power supply case to warm up during operation, especially in areas near internal components like transistors and diodes. Temperatures around 40°C (104°F) are typical under load.
  • Fan Operation: The cooling fan is designed to operate only when needed. If the fan is not running, it typically means the internal temperature is below the activation threshold (around 45°C or 113°F), which is normal and indicates efficient cooling management.
  • Ventilation is Key: Always ensure the power supply has ample space around it for air circulation to prevent overheating and ensure longevity.

9. Warranty and Support

For warranty claims, technical support, or service inquiries, please contact the manufacturer directly.

Manufacturer Information:

  • Company Name: SHENZHEN KNOA TECHNOLOGY CO., LTD.
  • Address: Unit 1606, 1, Building B, Jida Garden, 38 Jinyun Road, Nansan Community, Buji Street, Longgang District, Shenzhen, China
  • Email: 294411620@qq.com
  • Telephone: +86-15889456615

EU Authorized Representative:

  • Company Name: MJCM SARL
  • Address: FR-78 avenue des Champs Elysees Bureau 326
  • Email: mjcm190928@gmail.com
  • Telephone: +33-767213611

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.