1. Introduction
The SANPKON Red Infrared Light Therapy Belt is designed to provide targeted physiotherapy and pain relief. It features 120 LEDs combining 660nm red light and 850nm near-infrared light, utilizing advanced lighting technology for concentrated and efficient treatment. This device helps relieve fatigue and pain by allowing infrared LED light to penetrate deep into joints and soft tissues, promoting blood circulation, and aiding in muscle relaxation and recovery.

Figure 1: Woman demonstrating the use of the Red Infrared Light Therapy Belt.
2. Safety Warnings and Contraindications
2.1 General Warnings
- This device is not to be used by sleeping, unconscious, or intoxicated persons.
- Do not use if you have skin numbness caused by medication or other reasons.
- The LED therapy light is an electrical device. To avoid electrical shock:
- Do not STAND on the device.
- Do not wash electrical parts with water.
- Do not touch the plug or device with wet hands.
- Do not use if the cord or plug appears to be damaged.
- Do not use the unit if it has been damaged, torn, or has come into contact with water.
- Do not pull, lift, or carry the device by the power cord.
- Do not use the cord as a handle, close a door on the cord, or pull the cord against sharp edges or corners.
- Do not use near-heated surfaces.
- Do not crease or fold the device.
- Use the provided round packaging for storing the device to protect it from potential creases and folds.
- Do not allow children to use this device; it is not a toy.
- Do not use the unit on an open wound, as heat may increase circulation and cause bleeding.
- Light Sensitivity: If you are allergic to neoprene, do not use this product without first consulting a physician.
- Test your skin for light sensitivity prior to initial treatment:
- Power on the device.
- Place the device on a range of 1/4 of your forearm skin for 3 minutes.
- After 3 minutes, check the area. If the area has turned red, discontinue use.
2.2 Contraindications
Patients with the following diseases or symptoms are prohibited from using this product:
- Metastatic tumors, high fever, vasculitis obliterans, ophthalmopathy, malignant tumors, vascular compensatory insufficiency, active tuberculosis, acute soft tissue infections.
- Pregnancy period, bleeding tendency, skin sensory disturbances, and skin allergies.
- Acute injury within 72 hours.
- Patients with pacemakers, defibrillators, or other electronic implants.
- Do not use this device if your skin is light sensitive or you are currently using medication that may cause skin sensitivity to light. Doing so may result in a photosensitive reaction. Stop use immediately if you experience any adverse reactions.
2.3 Disclaimer
This product is not intended to diagnose, cure, or prevent disease. It makes no claims, representations, or warranties regarding its ability to cure any physical, skin, or mental conditions. A qualified health professional should be consulted regarding any condition requiring medical attention. No legal liability is assumed for misuse.
3. Package Contents
Please check the package for the following items:
- 1 x LED Therapy Light Belt
- 1 x Elastic Band
- 1 x Controller
- 1 x USB Cable
- 1 x Power Adapter (EU or US Plug, depending on your selection)
- 1 x User Manual

Figure 2: Package contents (EU Plug version shown).
4. Setup Instructions
Follow these steps to set up your LED Therapy Light Belt:
- Connect the Controller: Locate the connector on the LED Therapy Light Belt and the corresponding plug on the controller cable. Align the groove on the plug properly and insert it into the belt's connector until secure.
- Choose Power Source: You have two options to power the device:
- Socket Charging Mode: Connect the power adapter to the controller cable, then plug the adapter into a standard wall socket.
- Portable Power Bank Mode: Connect the USB cable to the controller cable, then plug the USB cable into a 5V power bank.

Figure 3: Proper connection of the controller to the belt.

Figure 4: Powering options for the therapy belt.
5. Operating Instructions
Once the device is connected to a power source, use the controller to operate it:
- Power On/Off & Frequency Setting: Press the Power button (circle with a line) to turn the device on or off. This button also cycles through frequency settings: 10Hz and 40Hz.
- Brightness Adjustment: Press the Brightness button (sun icon) to select one of 5 brightness levels (L1/L2/L3/L4/L5).
- Time Setting: Press the Timer button (clock icon) to set the treatment duration. Available options are 5, 10, 15, 20, 25, 30 minutes, or 'On' for continuous operation.
- Light Mode Adjustment: Press the Wave icon button to switch between 660nm (Red light only), 850nm (Near-Infrared light only), or 'All' (both red and near-infrared lights).
- Vibration Setting: The controller also features a vibration setting with 4 levels. (Refer to the controller diagram for the specific button, if available).

Figure 5: How to use the controller.
6. Maintenance
To ensure the longevity and proper functioning of your LED Therapy Light Belt, please follow these maintenance guidelines:
- Cleaning: Do not wash electrical parts with water. To clean the belt, wipe it gently with a soft, dry cloth.
- Storage: Do not crease or fold the device. Always use the provided round packaging for storing the device to protect it from potential creases and folds, which can damage the internal components.
- Handling: Avoid pulling or lifting the device by its power cord. Do not use the cord as a handle or pull it against sharp edges.
7. Troubleshooting
If you encounter any issues with your LED Therapy Light Belt, please try the following:
- Device Not Turning On:
- Ensure all connections (belt to controller, controller to power source) are secure.
- If using the power adapter, check if the wall socket is functional.
- If using a power bank, ensure it is adequately charged and providing 5V output.
- Check the power cord and plug for any visible damage.
- Lights Not Emitting:
- Verify the device is powered on and the brightness level is set above L1.
- Ensure the light mode is selected (Red, Near-Infrared, or All).
If the problem persists after trying these steps, please contact customer support.
8. Specifications
| Feature | Specification | Feature | Specification |
|---|---|---|---|
| Product Size | 45 x 21 cm | Power | Max 20W |
| LED Light Panel Size | 45 x 21 cm | Product Weight | 0.60 KG |
| Input Voltage | AC 100-240V | Power Bank Support | 5V (requires USB booster cable) |
| Output Voltage | DC 12V | LED Quantity | 120pcs 660nm Red Lights + 240pcs 850nm Near-Infrared Lights |
| Function | Pain relief, accelerate wound recovery, improve circulation, enhance resistance, improve sleep, weight loss | ||

Figure 6: Product Specifications.
9. User Tips
- For optimal results, consistently follow the recommended treatment times (e.g., 20-40 minutes per session).
- Ensure the device is comfortably secured to the target area using the elastic band for direct contact and effective light penetration.
- Start with shorter sessions and lower brightness levels if you are new to light therapy, gradually increasing as your body adjusts.
10. Warranty and Support
If you encounter any problems with your SANPKON Red Infrared Light Therapy Belt, please feel free to contact the seller or customer support for assistance. Refer to your purchase documentation for specific warranty details and contact information.