Thunder 02-1

Contents

Thunder 02-1 Electric Bicycle User Manual

Model: 02-1 | Brand: Thunder

1. Introduction and Safety Information

This manual provides essential instructions for the assembly, operation, and maintenance of your new Thunder 02-1 Electric Bicycle. Please read this manual thoroughly before your first ride to ensure safe operation and to maximize the lifespan of your e-bike.

1.1 General Safety Warnings

  • ⚠️ WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage.
  • While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
  • Always perform a safety check before each ride.
  • Do not modify the e-bike in any way that is not approved by the manufacturer.
  • Be aware of your surroundings and ride defensively.

1.2 Product Overview

The Thunder 02-1 is a city e-bike designed for adult use, featuring a 500W Bafang rear hub motor, 7-speed Shimano transmission, and mechanical disc brakes. It is equipped with a 48V Lithium battery and a SW-900 LCD display for monitoring ride data.

Thunder 02-1 Electric Bicycle in an outdoor setting
Figure 1: Thunder 02-1 Electric Bicycle, side view.

2. Assembly

Careful assembly is crucial for the safe operation of your e-bike. Please follow these steps precisely.

2.1 Installing the Front Wheel

Remove the shipping spacer, bolt, and nut from the front wheel fork.

  1. Remove the spacer between the front disc brake caliper. Do not squeeze the front brake handle. Squeezing the front brake handle will cause the pads to move and it may be difficult to position the front brake disc within the pads.
  2. Insert the axle into the front wheel hub. Insert the front wheel in between the forks while positioning the front brake disc in the brake caliper.
  3. Place a washer onto the axle on the outside of the forks.
  4. Install and hand-tighten the two adjustment nuts equally. Use the supplied 15mm socket wrench and 15mm wrench to finish tightening the adjustment nuts, being sure each nut is tightened equally on both sides.
  5. The adjustment nuts must be very tight; be sure to retighten them after your first two rides.
  6. Be sure to inspect that your front wheel is secured properly before every ride and adjust if necessary.
Diagram showing removal of shipping spacer and installation of front wheel
Figure 2: Front wheel assembly diagram, showing removal of shipping spacer and proper placement of the wheel and brake disc.

NOTICE: The front wheel must be inspected before every ride to ensure it is securely attached to the bike. Failure to test that the front wheel is properly secured could result in significant injury or even death.

2.2 Installing the Handlebars

  1. Be sure the fork and headset are pointing towards the front of the bike.
  2. Center the handlebar in the headset, taking care not to damage any wires.
  3. Install the clamp and screws. Alternately tighten the screws side-to-side until secure.
  4. Verify the headset and handlebar is lined up. You will re-adjust after installing the front wheel.
  5. Verify that all headset items are tight.
Diagram showing handlebar installation
Figure 3: Handlebar installation diagram, illustrating proper alignment and tightening of the clamp and screws.

2.3 Installing the Pedals

It's critical that the pedals are tightened firmly in the crank arm to prevent them from loosening while riding, which can result in significant damage to the bike.

  1. Identify the left ("L") and right ("R") markings on the pedals. Install "L" pedal on the left crank arm and "R" pedal on the right crank arm (chain side).
  2. While keeping the pedal horizontal, carefully hand-start the threads of the pedal into the crank arm.
  3. Finish tightening the pedals using the supplied 15 mm wrench. The pedals must be very tight. Check and retighten the pedals after your first two rides.
Diagram showing left and right pedal identification and proper tightening with a wrench
Figure 4: Pedal installation guide, showing "L" and "R" markings and the use of a 15mm wrench for secure tightening.

2.4 Adjusting Seat Height

When adjusting seat height, ensure the minimum insertion length mark on the seatpost remains inside the seat tube.

Diagram showing seat height adjustment
Figure 5: Seat height adjustment diagram, highlighting the minimum insertion length for safety.

NOTICE: The kickstand is designed to support the e-bike only. Do not sit on the e-bike with the kickstand engaged, as this could result in damage to the kickstand.

3. Operation

3.1 Initial Ride and Safety Check

Before your first ride, ensure all installed items are properly torqued, tightened, and connected. The e-bike can be ridden like a normal bicycle with the power ON or OFF. Pedal assist and throttle activate only when power is ON.

We recommend riding with pedal assist off initially to familiarize yourself with braking and gear shifting. Then, gradually test pedal assist levels to find optimal settings.

Safety Check Before Each Ride:

  • The battery pack must be charged and secured.
  • Remove keys from the battery pack.
  • The display must turn on and function properly.
  • The brakes must function properly.
  • The tires must be inflated to the proper psi (check tire sidewall for recommended pressure).
  • The front and rear lights must work properly.
  • The cable connections must be tight.
  • Wheels should be secured and the spokes tight.

3.2 Turning the E-Bike On and Off

To Turn On:

  1. Press the power button on the battery and then securely install the battery pack on the bike.
  2. Push and hold the mode button (or LCD power button for advanced display) on the display for 3 seconds. The display will illuminate, showing battery charge and selected pedal assist level.
Image of the e-bike battery power button
Figure 6: Location of the battery power button.

To Turn Off:

Push and hold the mode button (or LCD power button) for 3 seconds when the bike is on. The display will power down and the bike will shut off. You do not have to turn off the battery; shutting down the display turns off the bike.

Automatic Shutoff: The electronic system will automatically shut down after a preset period of time to conserve power.

3.3 Pedal Assist Control System (Pedelec)

The pedal assist system uses cadence sensors to measure your pedaling, transferring this information to the bike's controller to generate power. This system helps maintain a constant level of pedal assist.

Adjusting Assist Levels (Basic LED Display):

When the bike is on, push and release the mode button to cycle through pedal assist levels from P0 to P4, then back to P0.

  • P0: No assist, only the throttle will work.
  • P1, P2, P3, P4: Power output levels (all modes have a max speed of 20mph).
Image of the basic LED display showing assist levels
Figure 7: Basic LED display showing pedal assist modes (P0-P4).

3.4 Advanced Matrix Display Operation

The advanced matrix display acts as the dashboard for your e-bike, showing basic status like speed, distance, and battery level. It also offers an "advanced mode" for additional information and parameter adjustments.

Buttons on the Advanced Matrix Display:

  • Power Button: Located on the back side of the display.
  • "Assist Up" Button: Located on the front face of the display.
  • "Assist Down" Button: Located on the front face of the display.
Image of the advanced matrix display with button locations
Figure 8: Advanced Matrix Display, highlighting the Power, Assist Up, and Assist Down buttons.

Selecting Pedal Assist Level (Advanced LCD):

Use the "+" or "-" buttons to select the desired pedal assist level. The LCD will indicate your selection. Once you start pedaling, the controller will activate the motor.

Pedal Assist Levels (Advanced LCD)
LevelDescription
0Throttle Operation Only
ECOBattery Efficiency
1, 2, 3Speed Ranges
SSport
RRace Track Mode (Refer to local laws & regulations before using)

The e-bike will maintain constant pedal assist until brakes are applied, assist level is adjusted, you stop pedaling, or the battery runs down.

3.5 Throttle Operation

The throttle control is located on the right-side handlebar next to the LCD screen. You can use the throttle and pedal assist simultaneously, or the throttle alone.

To Use the Throttle:

  1. Turn on the battery and the display.
  2. Set the display to the desired setting. If "P0" is selected, pedal assist is unavailable.
  3. Rotate the throttle control to increase e-bike speed.

3.6 Reading the Battery Pack Level

The display indicates the battery pack's voltage. Voltage can vary based on conditions (e.g., uphill, cold weather). To accurately read the charge, release the throttle; the display will stabilize after 1 second.

  • 2 Bars: Recharge soon. Select a lower pedal assist level.
  • 1 Bar: Stop using the throttle; recharge the battery pack.
Image of the LED display showing battery level graphic
Figure 9: LED display showing battery level graphic, speed, and headlight indicator.

3.7 Understanding Battery Pack Range

E-bike range varies greatly depending on riding style, terrain, tire pressure, temperature, payload, and wind. You will gain a sense of your e-bike's range after a few rides.

Factors That Decrease Range:

  • Rapid accelerations using the motor.
  • Uphill riding.
  • Heavy payloads.
  • Headwinds.
  • Underinflated tires.
  • Extreme hot or cold weather.

How to Increase Your Range:

  • Start by pedaling instead of only using the motor.
  • Avoid rapidly accelerating using the throttle.
  • Pedal to help the motor up steep hills. Use the gears.
  • Reduce your average pedal assist level and pedal along with the motor.
  • Reduce payload weight.
  • Properly inflate the tires (30-35 psi).
  • Coast to a stop and avoid rapid decelerations.

NOTICE: If the battery pack power is low, choose a lower level of pedal assist if going on stops and hills. The sports mode will demand enough power to convince the battery pack that it is depleted, but you may still use a lower level of pedal assist. Riding downhill or pedaling when not using the throttle will not recharge the battery pack.

3.8 Activating the LED Headlight and Display Backlight

To Turn On/Off (Basic LED):

Press the mode button twice quickly. The headlight will come on, and a headlight icon will appear on the screen. Repeat to turn off.

To Turn On/Off (Advanced LCD):

Press and hold the "assist up" button for 2 seconds. The front LED headlight and the display's backlight will illuminate. A headlight status icon will appear. Repeat to turn off.

3.9 Activating Walk Mode

When pushing the bike uphill, use the WALK mode to assist you in moving the bike at walking speed.

To Activate:

Push and hold the "assist down" button. After 2 seconds, the motor will begin to turn at walking speed.

To Stop:

Release the "assist down" button. The motor will stop. Using either brake lever will also stop WALK mode.

3.10 Activating Cruise Control Function

Use the cruise control feature to maintain a desired speed without using the throttle or pedal assist.

To Activate:

Use the throttle or pedal assist to reach your desired speed. Push and hold the "assist down" button for 2 seconds. When the "C" graphic appears, release the "assist down" button. The current speed will be maintained. In CRUISE mode, the throttle is automatically modulated to maintain the desired speed.

To Discontinue:

  • Use the brakes by squeezing the brake lever.
  • Use the throttle.
  • Push the "assist up" or "assist down" button.

IMPORTANT NOTES: The maximum cruise controllable speed is 20 mph. If set above 20 mph, it will default to 20 mph. Pedal assist is still available during cruise control. If resistance is too high, the motor will provide more power to maintain speed.

3.11 Adjusting Parameters in the Setup Menu (Advanced LCD)

To Enter Settings Menu:

Hold the "assist up" and "assist down" buttons for about 3 seconds, then release. You can adjust settings like Unit, Speed Limit, Backlight, Torque, and Wheel Size.

Navigating and Entering a Menu Setting:

Use the "assist up" and "assist down" buttons to navigate. Push the power button once to enter a setting. Adjust the value with "assist up" and "assist down" buttons. Push the power button to exit the setting. Continue pressing and releasing the power button to exit the setup menu and return to the main screen.

Speed Limit Classification (Example)
ClassificationSet Power LimitSet Pedal AssistThrottle Operation
USA Class 1/750WSet NDW to 420 mph (32 km/h)Not allowed
USA Class 2/750WSet NDW to 420 mph (32 km/h)20 mph (32 km/h)
USA Class 3/750WSet NDW to 428 mph (45 km/h)20 mph (32 km/h)
Europe 250W/25 km/hSet NDW to 115.5 mph (25 km/h)Not Allowed
Europe S-Pedelec/45 km/hSet NDW to 428 mph (45 km/h)Not Allowed
Off-road mode**Set NDW to 528 mph (45 km/h)20 mph (32 km/h)

**Default configuration "please refer to local laws & regulations before using". Note: In all instances the throttle is limited to 20 mph.

4. Maintenance

4.1 Battery Care and Charging

The e-bike features a high-capacity lithium-ion rechargeable battery pack. It is recommended to charge the battery pack after every ride, even if lightly used, as lithium-ion batteries do not have a "memory effect."

Battery Safety Precautions:

  • Do not short-circuit the battery pack's terminals.
  • Do not charge if the temperature is over 140°F (60°C).
  • Do not disassemble the battery pack.
  • Do not submerge the battery pack in liquid or use it in wet areas.
  • Do not place the battery pack near fire or heat.
  • Do not expose the battery pack to freezing temperatures for an extended period. Do not charge a frozen battery pack; allow it to reach room temperature.

Charging Instructions (Onboard Charging):

  1. Stand the e-bike on its left side and locate the charge port dust cover on top of the battery pack.
  2. Rotate the dust cover to expose the DC charge port.
  3. Carefully plug the charger into the charge port.
  4. Connect the AC power cable into the charger and plug it into a power outlet. The charger will automatically start charging.
  5. When charging, the indicator LED will turn red. When fully charged (1-8 hours depending on battery size and initial charge), the light will turn green, and charging will stop automatically.
  6. Disconnect the charger from the wall.
  7. Remove the charger plug from the DC charge port. Rotate the dust cover to protect the port.
Image showing the e-bike battery and charge port location
Figure 10: E-bike battery and charge port location (refer to the PDF manual for detailed diagram).

NOTICE: Recharge the battery pack at least once every month. A battery pack left unused for several months may result in permanent capacity loss. Cold environments temporarily reduce the battery pack's capacity. Avoid using the electric bicycle in very hot weather. Store the e-bike in a sheltered place.

4.2 Hydraulic Brakes

The e-bike is equipped with front and rear disc brakes. These components require inspection for wear and tear. If the hydraulic brakes are worn, replacement will be needed. Wear varies by riding time, mileage, style, and location. We recommend inspecting your brakes before every ride.

  • The brake on the front wheel is controlled by the lever on the left-hand side of the handlebar.
  • The brake on the rear wheel is controlled by the lever on the right-hand side of the handlebar.
  • The front brake provides the majority of the e-bike's stopping power.
  • When slowing down on slippery surfaces, use the rear brake first before applying the front brake.
  • A signal wire from each brake lever automatically turns off the motor when either brake is being used. This prevents undue wear on the electric motor and battery.

NOTICE: Your new brakes will undergo a "bedding-in" period and will wear down after the first 40-50 full stops. The brakes will reach 100% of their grip capacity after this period. Adjust the brake lever so that it adapts to the newly bedded-in brakes. If there appears to be any issue with your braking system, do not use your bike and contact support or an authorized mechanic.

Mineral Oil Cups:

Have a trained mechanic service the mineral oil cups on the handlebars.

5. Troubleshooting

This section addresses common issues you might encounter with your Thunder 02-1 Electric Bicycle. For more complex problems, please refer to the full PDF manual or contact customer support.

5.1 Display Not Turning On

  • Ensure the battery pack is fully charged and securely installed.
  • Verify the battery power button is pressed.
  • Check that the display's mode/power button is pressed and held for 3 seconds.
  • Inspect cable connections for tightness.

5.2 Motor Not Providing Assist/Throttle Not Working

  • Ensure the e-bike is turned on and the display is active.
  • Check the battery level; if low (1-2 bars), recharge the battery.
  • Verify that the pedal assist level is not set to P0 (no assist).
  • Ensure brake levers are not engaged, as they cut power to the motor.
  • Check for any error codes on the display (refer to PDF manual for code explanations).

5.3 Reduced Range

  • Review "Factors That Decrease Range" in Section 3.7.
  • Ensure tires are inflated to the correct psi.
  • Consider riding in a lower pedal assist mode (e.g., ECO) to conserve battery.
  • Avoid rapid accelerations and heavy payloads.

5.4 Brakes Squealing or Feeling Weak

  • Brakes require a "bedding-in" period (40-50 full stops). Performance will improve after this.
  • Check brake pads for wear and replace if necessary.
  • Ensure brake levers are properly adjusted.
  • If issues persist, consult an authorized mechanic for hydraulic brake service.

6. Specifications

Below are the key technical specifications for the Thunder 02-1 Electric Bicycle.

FeatureSpecification
Model Number02-1
CertificationCE
Rated Passenger CapacityOne Seat
StyleStandard Type
Max Speed30 - 50 KM/H (25-42km/h listed elsewhere, refer to local regulations)
Wattage351 - 500W
Power SupplyLithium battery
Voltage48V
Battery48V 12Ah Lithium Battery
Motor48V 500W Bafang Rear hub motor
ForkMOZO/EXSHO front suspension forks
Frame Material6061 Aluminum alloy
Tire26''*1.95 Kenda Tires
BrakeF/R Mechanical disc brake
DisplaySW-900 LCD display
GearsShimano 7 speed gears
FoldableNo
Range30-50km
Max Load150kgs
Charging Time4-6 Hours
AccessoriesHeadlight, rear light, rear rack
Package Dimensions (L x W x H)155 x 25 x 80 cm
Package Weight33.9 kg

7. User Tips

  • For optimal battery life, avoid deep discharges and store the e-bike in a sheltered place, especially in extreme temperatures.
  • Regularly check tire pressure and brake function to ensure a safe and smooth ride.
  • Familiarize yourself with the different pedal assist levels and throttle control in a safe environment before riding in traffic.
  • Always wear appropriate safety gear, including a helmet, when riding.

8. Support and Documentation

For further details, advanced settings, or specific troubleshooting, please refer to the complete user manual PDF.

Download Full User Manual (PDF)

If you have any questions or require assistance, please contact the Peter Pan Electric Bicycle Specialty Store Store customer support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.