Audi S3 Emblem Letters Car Sticker

Contents

Audi S3 Logo Car Sticker Instruction Manual

Model: S3 Emblem Letters Car Sticker

Brand: Audi

Introduction

This manual provides comprehensive instructions for the installation, maintenance, and general use of your new Audi S3 Logo Car Sticker. Designed for durability and aesthetic enhancement, this emblem is a perfect accessory for your Audi S3 vehicle. Please read all instructions carefully before proceeding with installation.

Safety Information

  • CHOKING HAZARD: Small parts. Keep away from children under 3 years.
  • SHARP EDGES: Handle with care to avoid injury.
  • This product is intended for individuals aged 18 and above.
  • Ensure the application surface is clean and dry to prevent improper adhesion, which could lead to the emblem detaching.

Package Contents

Your package should contain the following item:

  • 1 x Audi S3 Logo Car Sticker
Hand holding an S3 car sticker, showing the black emblem on a yellow and black background.
Image: Audi S3 Logo Car Sticker (example color variant)

Product Specifications

Feature Detail
Product Name Audi S3 Logo
Material ABS (Acrylonitrile Butadiene Styrene)
Dimensions (L x W) 105mm x 38mm (4.13 inches x 1.5 inches)
Special Features Self-adhesive backing
Compatible Car Maker Audi (S3 8V, 8P, 8Y, 8L models)
Item Type Emblem / Car Sticker
Origin Mainland China
Product Weight Approximately 0.01 kg
Package Dimensions 16cm (L) x 12cm (W) x 1cm (H)
Two S3 emblems, one silver and one black, with dimensions 105mm length and 38mm width indicated.
Image: S3 Emblem with dimensions
Four S3 stickers with different color backgrounds: green, blue, yellow, and orange.
Image: Various color options for the S3 sticker

Setup Instructions

Follow these steps for proper installation of your S3 Logo Car Sticker:

  1. Prepare the Surface: Choose a clean, flat, and smooth surface on your vehicle where you wish to apply the sticker. Ensure the area is free from dust, dirt, wax, and grease. Use an alcohol wipe or a mild cleaning solution and a clean cloth to thoroughly clean the surface. Allow it to dry completely.
  2. Positioning: Before removing the adhesive backing, carefully place the sticker on the desired location to confirm the positioning. You may use painter's tape to mark the exact spot for precise alignment.
  3. Peel the Backing: Gently peel off the protective film from the adhesive side of the sticker. Avoid touching the adhesive with your fingers to maintain its stickiness.
    A hand peeling the white protective backing off the adhesive side of an S3 car sticker.
    Image: Peeling the adhesive backing
  4. Apply the Sticker: Carefully align the sticker with your pre-marked position and press it firmly onto the surface. Start from one side and slowly work your way across, applying even pressure to avoid air bubbles. Use a soft cloth or a plastic squeegee to smooth out any bubbles and ensure full contact with the surface.
  5. Curing Time: For optimal adhesion, avoid washing your car or exposing the sticker to extreme weather conditions for at least 24-48 hours after application. This allows the adhesive to fully cure.

Operating Instructions

Once installed, the Audi S3 Logo Car Sticker requires no further operation. It is designed to be a static decorative emblem that enhances the visual appeal of your vehicle. Enjoy the refreshed look!

Maintenance

To ensure the longevity and appearance of your S3 Logo Car Sticker:

  • Cleaning: Clean the sticker gently with mild soap and water. Avoid using abrasive cleaners, harsh chemicals, or high-pressure washers directly on the emblem, as this can damage the finish or adhesive.
  • Protection: While durable, prolonged exposure to direct sunlight and extreme weather can affect the sticker over time. Parking in shaded areas when possible can help preserve its color and adhesion.
  • Inspection: Periodically check the edges of the sticker for any signs of lifting. If lifting occurs, gently press down to re-secure, or consider re-applying if the adhesive has failed.

Troubleshooting

  • Sticker not adhering properly:
    • Ensure the surface was thoroughly cleaned and dry before application.
    • Verify that the ambient temperature was suitable for application (ideally above 10°C / 50°F).
    • Apply firm, even pressure during installation.
  • Air bubbles under the sticker:
    • For small bubbles, you can try to gently push them towards the edge with a soft cloth or plastic squeegee.
    • For stubborn bubbles, a very fine needle can be used to prick the edge of the bubble and then smooth it out.
  • Sticker peeling at edges:
    • Clean the lifted area and the vehicle surface underneath. Apply a small amount of strong automotive adhesive if necessary, and press firmly.

User Tips

  • Compatibility Check: Before purchasing, always verify the dimensions of the sticker against the intended application area on your specific Audi S3 model (e.g., 8V, 8P, 8Y, 8L) to ensure a perfect fit.
  • Temperature for Application: For best results, apply the sticker in moderate temperatures, ideally between 15°C and 25°C (60°F and 77°F). Extreme cold can reduce adhesive effectiveness, while extreme heat can make the sticker too pliable and difficult to handle.
  • Pre-fitment: Use masking tape to temporarily hold the emblem in place before removing the adhesive backing. This allows you to step back and ensure the alignment is perfect from various angles.

Warranty & Support

For any product-related inquiries or support, please contact the manufacturer or their authorized representatives:

Manufacturer:

Yiwu Xinfang Network Technology Co., Ltd
Room 301, Building 22, No. 3, Beicun Community,
Choujiang Street, Yiwu City, Jinhua City, Zhejiang Province, China
Tel: +86 15257111041
Email: xinfang17@163.com

EU Representative:

MJCM SARL
78 avenue des Champs, Elysées Bureau 326,
Paris, France, 75008
Tel: +33-767213611
Email: mjcm190928@gmail.com

This product is manufactured in Mainland China.

Additional Documentation

A detailed user manual in PDF format is available for download:

User Manual (PDF)

© 2024 Audi Auto Accessories Store. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.