Toviyon TPA Series

Contents

Toviyon TPA Series DC Power Supply Instruction Manual

Model: TPA Series

1. Security Summary

Welcome to our DC regulated power supply (referred to as the power supply). This manual contains essential safety instructions that must be followed for the operation, use, and storage environment of this product series. To ensure your personal safety, please thoroughly read this manual before operation to avoid personal injury due to improper handling or damage to the power supply and other connected load equipment.

Safety Symbols

The following safety symbols may appear in the manual or on the machine:

Warning Label symbol

Warning Label

High Volt Danger symbol

High Volt Danger

Grounding symbol

Grounding

Certification Mark CE symbol

Certification Mark (CE)

Do Not Litter symbol

Do Not Litter

Indoor Use symbol

Indoor Use

Note: Generic placeholder images are used for symbols as specific symbol images were not provided in ALLOWED_URLS. Please refer to the physical manual for exact symbols.

2. Product Overview

The TPA series is a digital display programmable switching DC regulated power supply that can simultaneously display voltage, current, and power. This power supply is widely used in product aging, battery charging, R&D testing, schools, and production lines. Its output voltage and current are both adjustable via an encode knob, continuously adjustable between 0 and the nominal value.

The power supply has excellent stability and ripple coefficient, and features multiple protection circuits including short-circuit protection, overvoltage protection, overcurrent protection, and overtemperature protection.

The product boasts an attractive design, user-friendly operation, and the ability to work at full capacity for extended periods. It is equipped with a USB fast charging interface and offers optional PC software control functionality, making it a popular choice among users.

3. Setup (Usage Requirements)

3.1 AC Input

Please verify the AC voltage input permitted for this machine. Refer to the label information located near the power outlet on the back of the machine for specific voltage requirements.

  • 230V ±10% 50Hz
  • 115V ±10% 60Hz

⚠ Warning:

Incorrect AC voltage input will cause serious damage to the machine. Please ensure that the machine requires the correct input voltage.

3.2 Connect the Ground Wire

When using this product, please ensure the power cord is properly grounded. If the power outlet does not have a ground wire, you can use a wire to connect the machine's grounding terminal to the earth. Proper grounding can effectively prevent machine leakage and reduce output ripple interference.

ⓘ Note:

Proper grounding effectively prevents machine leakage and can also reduce output ripple interference.

3.3 Connect the Load Device

  1. Securely connect the output wires to the power supply terminals according to the positive (+) and negative (-) markings.
  2. Securely connect the other end of the output lead to the positive terminal of your load device.

⚠ Notice:

Incorrect connections may damage the power supply and the load connected to it. When connecting loads such as batteries, do not reverse the "+" and "-" terminals, as this may damage the power supply.

4. Front Panel Introduction

The front panel of the TPA Series DC Power Supply features various controls and indicators for operation. Refer to the diagram and table below for a detailed overview.

Front panel of Toviyon DC Power Supply with numbered labels

Figure 1: Front Panel Layout (Note: Generic placeholder image used for diagram. Please refer to the physical manual for the exact diagram.)

No. Description No. Description
1Voltage Display12Short-Circuit/Overcurrent Protection Switch (OCP)
2Current Display13Over Voltage Protection Switch (OVP)
3Power Display14Buzzer Switch
4C.V (Constant Voltage Indicator Light)15Output Switch
5M1-M4 Storage Indicator Light16USB-A Fast Charging Port
6C.C (Constant Current Indicator Light)17USB-C Fast Charging Port
7OPN Indicator Light18Power Switch
8Current adjustment knob19Negative Output Port (Black)
9Voltage Adjustment Knob20Ground Terminal (Green)
10Button Lock Switch21Positive Output Port (Red)
11Storage Selection/storage Value Setting Switch

5. Back Side Description

The back panel includes the cooling fan, power input, and communication ports.

Back panel of Toviyon DC Power Supply with numbered labels

Figure 2: Back Panel Layout (Note: Generic placeholder image used for diagram. Please refer to the physical manual for the exact diagram.)

No. Description
22Temp-Controlled Cooling Fan
23Power Outlet
24Fuse Box
25USB/RS-232/RS-485 Communication Port (Optional)

6. Operating Instructions

6.1 Constant Voltage Constant Current Mode

The power supply output modes are divided into two types: constant voltage output (C.V) and constant current output (C.C). The output mode is determined by the voltage and current values set by the user and the load connected to the power supply. The voltage or current value output by the power supply will not exceed the voltage and current values set by the user. In constant voltage mode, the output voltage is equal to the user-set voltage value. In constant current mode, the output current is equal to the user-set current value.

⚠ Important Note on CV/CC Transition:

During actual CV operation, if the load resistance decreases and causes the output current to increase to the set current value, the power supply will automatically switch to CC mode. When the load resistance continues to decrease, the current will remain at the set current value while the voltage proportionally decreases (I=V/R). At this point, increasing the load resistance or raising the current set value will restore the CV output mode.

6.2 VOLTAGE Adjustment Knob

Used to adjust the voltage setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the voltage knob will jump to the left, skipping a character position. After 3 seconds, the flashing will stop and the current setting value will be saved.

High-precision encoder adjustment knob for setting digits on Toviyon DC Power Supply

Figure 3: High-Precision Encoder Adjustment Knob

6.3 CURRENT Adjustment Knob

Used to adjust the current setting. Rotate clockwise to increase the value; rotate counterclockwise to decrease the value. Pressing the current knob will jump to the left. The flashing will stop 3 seconds after the current setting is complete, and the current setting will be saved.

6.4 LOCK Button Lock Switch

Used to lock the state of the push-button switches (excluding the power switch and LOCK button lock switch) and adjustment knobs on the front panel to prevent accidental operation.

Toviyon DC Power Supply showing the one-click output locking feature

Figure 4: One-Click Output Locking

Video 1: Demonstration of voltage/current adjustment, memory presets, and output lock.

6.5 Memory Storage Group Selection/Storage Value Setting

This machine has four sets of memory functions (M1-M4), which makes it easy to store and recall frequently used parameters.

Toviyon DC Power Supply illustrating 4 groups memory storage function (M1, M2, M3, M4 presets)

Figure 5: 4 Groups Memory Storage Function

Storage Group Selection:

Press the MEMORY button to select any one of the four preset voltage/current storage values (M1, M2, M3, or M4). The selection result can be confirmed through the display screen and the M1~M4 storage indicator lights on the display screen.

Stored Value Settings:

For example, to change the value stored in M2:

  1. Press the MEMORY button to select M2 for storage.
  2. Press and hold the MEMORY button for 3 seconds to enter the parameter setting interface (you will hear two "beep" sounds).
  3. Use the VOLTAGE/CURRENT knob to adjust to the desired voltage/current value.
  4. After modification, press and hold the MEMORY button for 3 seconds within 8 seconds to save (you will hear two "beep" sounds). The setting will be completed.
  5. If you do not save within 8 seconds, the parameter setting interface will be automatically exited without saving.

6.6 OCP Short-Circuit Protection/Overcurrent Protection Switch

Press the OCP button to enable/disable the OCP short-circuit protection/overcurrent protection function. When this function is enabled, the button indicator light will illuminate. If a short circuit or overcurrent occurs in the load, the machine will stop output and issue an alarm. Pressing the OUTPUT button or the OCP button will deactivate the alarm and shut off the power output.

ⓘ Note:

The machine determines whether a short circuit exists by checking if the output current exceeds the user-set current. Therefore, the machine cannot be used in constant current (CC) mode when the OCP short-circuit protection function is enabled.

OCP Parameter Setting Method:

Press and hold the OCP button for 3 seconds to enter the OCP parameter setting interface (you will hear two "beep" sounds). Use the CURRENT knob to adjust to the desired current protection value. After modification, press and hold the OCP button for 3 seconds within 8 seconds to save the settings (you will hear two "beep" sounds). If you do not save within 8 seconds, the settings will be automatically exited without saving.

6.7 OVP Over Voltage Protection Switch

Press the OVP button to enable/disable the OVP overvoltage protection function. When this function is enabled, the button light will illuminate. When an overvoltage occurs, the machine will stop outputting and issue an alarm. Pressing the OUTPUT button or the OVP button will deactivate the alarm and turn off the power output.

Toviyon DC Power Supply demonstrating OCP (Overcurrent Protection) and OVP (Overvoltage Protection) safety features

Figure 6: OCP/OVP Protection

OVP Parameter Setting Method:

Press and hold the OVP button for 3 seconds to enter the OVP parameter setting interface (you will hear two "beep" sounds). Use the VOLTAGE knob to adjust to the desired voltage protection value. After modification, press and hold the OVP button for 3 seconds within 8 seconds to save the settings (you will hear two "beep" sounds). If you do not save within 8 seconds, the settings will be automatically exited without saving.

6.8 Buzzer Switch

Press the buzzer button (Buzzer icon) to turn the buzzer on or off. (Note: Generic placeholder image used for buzzer icon as specific icon image was not provided in ALLOWED_URLS. Please refer to the physical manual for exact icon.)

6.9 OUTPUT Output Switch

Press the OUTPUT button to turn the power output on or off.

6.10 OPN Function

The OPN function controls whether the OUTPUT button is ON or OFF each time the device is powered on.

How to enable/disable the OPN function:

  1. With the OUTPUT button OFF, press and hold the OUTPUT button for 3 seconds to enter the settings interface (you will hear two "beep" sounds).
  2. Press the OUTPUT button or rotate the VOLTAGE/CURRENT knob to select whether the OPN function is on or off.
  3. After making your selection, press and hold the OUTPUT button for 3 seconds to save and exit (you will hear two "beep" sounds).

6.11 USB Fast Charging Function

This device features USB fast charging and has a built-in multi-protocol fast charging identification chip, with a maximum output power of 18W.

Toviyon DC Power Supply with USB-A and USB-C fast charging ports in use

Figure 7: USB & Type-C Fast Charging

6.12 Host Computer Communication (Optional)

Users can choose models equipped with USB / RS-232 / RS485 communication modules to communicate with a host computer via the MODBUS protocol, enabling remote control.

RS-485 Address Setting Method:

Press and hold the VOLTAGE knob for 3 seconds to enter the address setting interface. Adjust the VOLTAGE knob to set the RS-485 address. After setting, press and hold the VOLTAGE knob to save and exit.

7. Maintenance

7.1 Regular Inspection, Cleaning, and Maintenance

Regular inspection, cleaning, and maintenance of the machine can help extend its lifespan. Please follow the steps below to maintain your machine:

  1. Turn off the power switch and unplug the power cord from the socket.
  2. Gently wipe the casing, top cover, and vents with a soft cloth and mild detergent.
  3. Visually inspect all power cords and terminals for damage such as impact, loosening, heat corrosion, moisture, or insect bites.
  4. Replace any damaged power cords or terminals with those of the same specifications and dimensions.

7.2 Replace Fuse

If the fuse blows, the machine will stop working. Find and correct the cause of the blown fuse before replacing it with a fuse of the same specifications.

Diagram showing how to unplug power cord and open fuse holder

How to replace a fuse: First, unplug the power cord, then open the fuse holder as shown in the diagram. (Note: Generic placeholder image used for fuse replacement diagram. Please refer to the physical manual for the exact diagram.)

Diagram showing how to reinsert fuse holder after replacement

After replacing the fuse with one of the same model and specifications, reinsert the fuse holder. (Note: Generic placeholder image used for fuse replacement diagram. Please refer to the physical manual for the exact diagram.)

⚠ High Volt Danger:

For effective safety protection, only fuses of specific specifications should be replaced. Do not unplug the power cord before replacing the fuse.

8. Troubleshooting

This section outlines common issues and their resolutions. For problems not listed here, please contact customer support.

  • No Output / Alarm Sounding (OCP/OVP): If the machine stops outputting and an alarm sounds, it indicates that either Overcurrent Protection (OCP) or Overvoltage Protection (OVP) has been triggered.
    • Resolution: Press the OUTPUT button or the respective OCP/OVP button to deactivate the alarm and shut off the power output. Check your load for short circuits or excessive current/voltage demands, and adjust settings if necessary.
  • Machine Not Working (Fuse Blown): If the unit is completely unresponsive, the fuse may have blown.
    • Resolution: Refer to the "Replace Fuse" section (7.2) for instructions. Ensure the cause of the blown fuse is identified and corrected before replacing it with a fuse of the correct specifications.
  • Accidental Operation: Unintended changes to settings.
    • Resolution: Use the LOCK button lock switch (6.4) to disable front panel controls during operation.

9. Specifications (TPA Series)

The following parameters were measured at an ambient temperature of 25±5°C, relative humidity <80%RH, and after preheating for 30 minutes. Actual parameters may vary slightly.

Parameter TPA305 TPA3010 TPA605 TPA1203 TPA1602
Output Volt0-30V0-30V0-60V0-120V0-160V
Output Current0-5A0-10A0-5A0-3A0-2A
Output Power0-150W0-300W0-300W0-360W0-320W
Fuse3.15A5A5A5A5A
AccessibilityDual fast charging ports, short circuit protection, four storage groups, lock function, buzzer, one-button output.
C.V Voltage Stability≤0.5% + 3mV
C.V Load Stability≤0.5% + 3mV
C.V Ripple≤0.5% Vp-p
C.C Current Stability≤0.5% + 3mA
C.C Load Stability≤0.5% + 3mA
C.C Ripple≤0.5% Ap-p
Product DimensionsLength 214mm, Width 90mm, Height 156mm
Product WeightNet weight: 1.17 kg. Gross weight: 1.55 kg.
Operating Temp0°C - 40°C, Relative humidity: <80%RH
Storage Temp10°C - 50°C. Relative humidity: <70%RH
Protection MethodOvervoltage Protection, Overcurrent Protection, Overtemperature Protection, Short Circuit Protection
Display Accuracy0.5% + 3 words
Maximum ResolutionVolt: 0.001V; Current: 0.001A

10. Warranty and Support

10.1 Product Inspection

Each product comes with an instruction manual and a certificate of conformity to ensure that users can use our products correctly. All products manufactured and inspected by our company are produced and inspected according to the manufacturer's standards; any unqualified products will never leave the factory.

10.2 Product Warranty

One-year warranty (excluding damage caused by human error).

10.3 Product Repair

  1. Free repair or replacement of parts is provided during the warranty period. After the warranty period, paid repair services are available.
  2. During the product's service life, if the product malfunctions, the company is only responsible for the malfunction and loss of the product itself; the company does not bear any load or other related losses.

Guarantee Limitations:

The following warranties do not apply to losses caused by the following circumstances:

  • Customer violation of the usage instructions in this manual
  • Customer disassembly or repair of the product
  • Unauthorized modifications or misuse
  • Operation of the product outside the specified environment
  • Force majeure factors under relevant laws

10.4 Packing List

  • Main unit x 1
  • Power cord x 1
  • Output load cable x 1
  • User manual x 1
  • Warranty card and certificate of conformity x 1

10.5 Contact Information

Shenzhen Toviyon Electronics Technology Co., Ltd.

  • Address: Room 203, 2nd Floor, No. 69, Langkou Industrial Park, Langkou Community, Dalang Subdistrict, Longhua District, Shenzhen
  • Web: www.toviyon.com
  • Tel: (+86)18588483965
  • WhatsApp: +1(424)413-3536
  • WeChat: 18588483965

For more services, you can also visit our official website by scanning the QR code:

QR code to Toviyon official website

(Note: Generic placeholder image used for QR code as specific QR code image was not provided in ALLOWED_URLS. Please refer to the physical manual for the exact QR code.)

A detailed user manual in PDF format can be found at: Toviyon DC Power Supply User Manual (PDF)

11. User Tips

  • Always double-check your voltage and current settings before enabling output to prevent damage to your circuit or the power supply.
  • Utilize the memory presets (M1-M4) for frequently used voltage/current combinations to save time and ensure consistent settings.
  • When working with sensitive electronics, enable OCP and OVP with appropriate limits to protect against unexpected conditions.
  • The encoder knob allows for precise adjustments; press it to switch between digits for fine-tuning.
  • Remember to use the LOCK function to prevent accidental changes during long test runs or when the device is unattended.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.