Aqara Smart Door Lock N200

Contents

Aqara Smart Door Lock N200 User Manual

Model: Smart Door Lock N200

1. Introduction

The Aqara Smart Door Lock N200 is an intelligent door lock supporting multiple unlocking methods including fingerprint, password, key, Bluetooth, and NFC. It features door lock status detection, low battery reminders, pry alarm, double verification unlocking, and multiple failed verification alarms. It also offers a one-key arming mode for controlling multiple devices and integrating with smart home applications for联动报警 (linked alarms).

For remote alarm reception, remote viewing of unlock records, smart linkage, and arming mode, the device needs to be paired with a Bluetooth gateway.

2. Package Contents

Before installation, please ensure all components are present and in good condition. The package typically includes:

  • 1 x Front Panel
  • 1 x Rear Panel
  • 1 x Standard Lock Body (with standard strike 240mm * 24mm)
  • 1 x Frame Reinforcer
  • 1 x Box of Fixing Screws
  • 1 x Electronic Lock Cylinder
  • 2 x Emergency Keys
  • 8 x AA Batteries
  • 1 x Large Square Shaft
  • 1 x Small Square Shaft
  • 2 x Interlock Screws
  • 2 x Adapters
  • 1 x Fixing Screw
  • 1 x Cutting Hole Drawing
  • 1 x User Manual
Aqara Smart Door Lock N200 Front and Rear Panels

Image: Front and rear panels of the Aqara Smart Door Lock N200.

Aqara Smart Door Lock N200 Angled View

Image: Angled view of the Aqara Smart Door Lock N200.

3. Specifications

FeatureSpecification
Product NameSmart Door Lock N200
ModelZNMS17LM
Dimensions (Panel)366 * 76.9 * 25.5mm
Net Weight4.0kg
Power Supply8 x AA batteries (6V), Type-C emergency power (5V)
ConnectivityBluetooth 5.0
Operating Temperature-25℃ ~ 70℃
Operating Humidity0 ~ 93% RH, non-condensing
Product Safety LevelB Level
Lock Cylinder Safety LevelC Level
Suitable for Mortise6068
Fit Door Thickness40-80mm
Ways To UnlockCard, Mechanical Keys, Password, Fingerprint, Bluetooth, Other
Smart Home PlatformMi Home, Apple HomeKit
CertificationCE

Hazardous Substances Information

This table is compiled in accordance with SJ/T 11364 regulations.

Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr(VI)) Polybrominated Biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDE)
Plastic ComponentsOOOOOO
Panel MetalOOOOOO
Copper AlloyXOXOOO
Other Internal Metal StructuresXOOOOO
PCBA and Other ComponentsOOOOOO

O: Indicates that the content of the hazardous substance in all homogeneous materials of the component is below the limit specified in GB/T 26572.

X: Indicates that the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit specified in GB/T 26572.

4. Setup and Installation

Important: The installation process requires specialized tools and expertise. It is highly recommended to hire a professional for installation. If your purchase includes on-site installation services, please scan the QR code below to schedule an appointment or consult customer service.

QR code for installation service

Scan to schedule installation service or learn more about the product.

4.1 Pre-Installation Checks

  1. Check Door Thickness: Use a ruler to measure the door thickness. It should be more than 40mm and less than 120mm.
  2. Inspect Door Condition: Check if the door body and door frame are deformed or scratched. Ensure each function of the original lock works normally.
  3. Inspect Lock Components: Verify all parts listed in the package contents are present and undamaged.
  4. Test Handle Functionality: Check whether the front and rear door handles can spring back normally under force.
  5. Test Key Cover and Lock Button: Check whether the key cover can spring up, rotate, and retract normally. Verify the outside lock button functions normally.
  6. Initial Power-Up Test: Connect the cables between the front and rear panels. Install 4 AA batteries into the compartment on the rear mounting plate. Wake up the panel; the buttons, indicator light, and backlight should light up normally.
  7. Test Lock Cylinder: Insert an emergency key into the lock cylinder to test whether it can rotate normally.
  8. Test Lock Body Bolts: Press the latch bolt and the assistant bolt of the lock body to test whether they can spring back under force. Test whether the dead bolt of the lock body can normally extend or retract. Test whether the lock-out bolt can normally extend or retract under force.

4.2 Reverse the Latch Bolt and Replace the Strike

Remove the lock body with the latch bolt and the assistant bolt facing up and the lock-out bolt facing down. Compared with the original lock body:

  1. Whether the size of the strike is the same.
  2. Whether the direction of the latch bolt is the same.

If they meet the requirements, they can be used directly. If not, you need to do the following process for the new lock body:

  • Remove the two screws from the strike and remove the strike.
  • Rotate the latch bolt 180 degrees.
  • Insert the small latch bolt into the strike, then install the adapted strike.

4.3 Reverse the Door Handles

Take out the front and rear panels of the new lock and compare the door handles with the original lock. If the door handles are in the same direction, they can be used directly. Otherwise, you need to reverse the door handles:

  • Reverse the front handle: Remove the screws of the front door handle, then rotate the handle 180 degrees downwards and install the screws to their original positions.
  • Reverse the rear handle: Remove the screws of the rear door handle, then rotate the handle 180 degrees downwards and install the screws to their original positions.

4.4 Confirm the Hole Height of the Door Lock

Under normal circumstances, the height of the front door handle is about 1.2m, the height of the living room door handle is about 1m, and the user's actual habits can customize the height of the handle.

4.5 Use the Cutting Hole Drawing to Cut Out Holes

  • The product box contains the cutting hole drawing to assist cut out a hole and confirm the position of the door lock.
  • After making sure the center position of the handle, secure the drawing on the center position so that the side of the drawing will overlap the side of the door.
  • When punching a hole, strictly follow the drawing. The center line of door thickness in the cutting hole drawing should aligned with that of the door. The height scale of the door handle should be aligned with the center line of door thickness in the cutting hole drawing, to avoid cutting out an oversize or undersize hole to affect installation.

4.6 Installation Difference between Wooden Door and Iron Door

  • Iron Door: If it is an iron door, there is no need to cut space because the iron door is hollow. Just pay attention to whether the original hole position on the facade is suitable for installation, and only choose the suitable strike.
  • Wooden Door: If it is a wooden door, you need to reserve the screw holes for the strike and use a chisel or other tool to cut out some space in the door slot for the connection line. At the same time, you need to extend the sky-ground hook of the lock body and remove it in case of insufficient space.

4.7 Fix the Lock Body

  • Insert the lock body in the door slot.
  • Pull the lock connection cable from the uppermost hole to the inside of the door.
  • Use two screws to install and fix the opposite corners of the lock body. It is not recommended to install the sky-ground hook.

4.8 Install the Lock Cylinder

  • Insert the lock cylinder from the inside of the door to the outside of the door.
  • Screw the screws into the front of the lock body to fix the lock cylinder on the lock body.

4.9 Install the Large Square Shaft

  • Make the big square shaft overlap the center point of the strike.
  • Use a ruler to measure the distance (15mm-20mm) beyond the facade between the two ends of the large square shaft.
  • Insert the large square shaft marked with "inside" and the inward arrow in the direction of the shrapnel facing up from the outside of the lock door to the inside of the door firmly. From the inside of the door, you see the shrapnel popping up and jamming the lock body.
  • Use a vise to clamp the large square shaft on the outside of the door, rotate it upward, and the lock bolt extends; rotate it downward and the lock bolt does not move.
  • Use a vise to clamp the large square shaft on the inside of the door, rotate it downward, and the lock bolt retracts; rotate it upward, and the lock bolt extends.

4.10 Install the Adapters and the Lock-Out Small Square Shaft

The length of the adapters and the shaft must be less than the door thickness to avoid that it's so long as to touch the panel.

  • Install two adapters on the front panel. They must be tightened and keep upright to avoid slant.
  • Rotate the lock-out button of the rear panel to the vertical direction.
  • Rotate the plastic buckle of the lock-out hole on the rear panel 45 degrees.
  • Insert the lock-out small square shaft into the lock-out hole, and then rotate the plastic buckle 45 degrees.

4.11 Install the Front and Rear Panels

  • Insert the connection cable of the front panel through the door hole from the outside of the door into the inside of the door.
  • Then align the handle hole with the large square shaft, and insert the adapters into the holes on both sides of the lock body and the lock cylinder.
  • The cable connects the front panel, the lock body, the lock cylinder and the rear panel. The buckle should be fastened.
  • Then align the handle hole on the rear panel with the large square shaft and insert the small square shaft into the small square shaft hole of the lock body.
  • Tighten the front and rear panels. Install the interlock screws through the screw holes on the rear panel (fix the front and rear panels). The length of the interlock screws must be equal to the door thickness -15mm, to avoid that it's so long as to touch the panel.
  • Install the rubber cap under the lock-out button, and the rubber cap of the interlock screw holes in the battery compartment. Make sure there is no gap and it is reliable.

4.12 Install the Frame Reinforcer

  • Nearly close the door, and mark line on the door (above the latch bolt) and draw a horizontal line at the height above the latch bolt.
  • Draw a vertical coincident line, based on the frame reinforcer and the center of the door. Confirm the exact position of the frame reinforcer.
  • Then confirm 4 screw holes, punch holes and install the screws to fix the frame reinforcer.
  • The large area between the latch bolt and the main lock bolt is installed upwards to avoid reverse the installation.

4.13 Test the New Lock

  • When the door is open, shake the door lock hard (the door lock will not shake).
  • Lift up the front panel handle, then the lock bolt extends. Release your hand and the handle springs back; Press down the front panel handle, then the lock bolt doesn't move. Release your hand and the handle springs back.
  • Press and hold the anti-peephole button on the rear panel. Then press down the handle and the lock bolt and the latch bolt retract. Then release your hand, and the latch bolt extends automatically. The handle springs back.
  • Rotate the lock-out button, and the lock-out bolt extends; rotate the lock-out button back, and the lock-out bolt retracts.
  • Install the left 4 AA batteries into the compartment of the rear panel. Install the battery cover.
  • Test whether keys, password and fingerprint unlock are normal.
  • Test whether emergency keys are normal to unlock.
  • Install the other two screws to fix the lock body.

Video: Aqara Smart Door Lock N200 Installation Guide. This video demonstrates the complete installation process from unboxing to final testing.

5. Operating Instructions

5.1 Initial Setup (Local Mode)

If you cannot use the mobile APP to set up the door lock, short press the "Settings" button under the battery cover of the door lock, and after verifying the administrator's fingerprint or password, you can perform the following operations:

  1. Add/Delete ordinary users.
  2. Set door lock volume.
  3. Set door lock voice language (supports Chinese/English).

Note: To enter local setup mode, first complete adding the door lock and user operations using the Mi Home APP.

5.2 Connecting to Mi Home APP

The product has been connected to Mi Home, and can be controlled via the Mi Home APP or Xiao Ai speaker, and interconnected with other products.

Scan the QR code to download and install the Mi Home APP. Users who have already installed the Mi Home APP can directly enter the device connection page. Alternatively, search for "Mi Home" in the app store, download and install the Mi Home APP. Open the Mi Home APP homepage, click "+" in the upper right corner of the page, and add the device according to the APP prompts.

Note: After the door lock is successfully added, it will automatically try to connect to the Bluetooth gateway device under the account, no configuration is required. The effective Bluetooth communication distance of the door lock is 10m, and walls and other obstacles may affect the Bluetooth communication distance.

Due to upgrades and updates of the Mi Home APP, the actual operation may differ from the description above. Please follow the instructions within the current Mi Home APP for operation.

5.3 Adding Users (via APP)

Enter the door lock device page and add the first user (default administrator) according to the APP prompts.

Note: If no user is added, the door lock cannot be locked normally. Please complete the door lock settings according to this manual as soon as possible.

5.4 HomeKit Connection (for iOS users)

Open the Apple "Home" app, click "+" in the upper right corner of the page, select "Add Accessory"; scan or manually enter the HomeKit setup code on the back cover of the door lock or below (please keep it properly), and complete the addition operation according to the prompts.

5.5 Unlocking Methods

Fingerprint Unlock:

  1. Gently press the added fingerprint on the fingerprint recognition area.
  2. After successful verification, press down the handle to unlock.

Password Unlock:

  1. Enter the added password and press the confirm key.
  2. After successful verification, press down the handle to unlock.

Emergency Key Unlock:

  1. Press the emergency keyhole cover.
  2. The cover springs up and rotates.
  3. Insert the key and rotate the key to unlock.

Note: Do not leave the emergency key locked inside the room. Choose a safe and accessible place to store it for extreme situations.

NFC Unlock:

  1. Place the added NFC device near the recognition area.
  2. After successful verification, press down the handle to unlock.
NFC Unlock with Wristband

Image: Unlocking the Aqara Smart Door Lock N200 using an NFC-enabled wristband.

7 Unlock Methods Diagram

Image: Diagram illustrating the 7 available unlock methods: Fingerprint, Password, Temporary Password, NFC, Key, Xiaomi APP, and HomeKit.

5.6 Locking Methods

Indoor Locking:

  1. Press the anti-peephole button.
  2. Press down the handle to lock.

Outdoor Locking:

Close the door and lift the handle upwards to lock.

Indoor Reverse Locking:

  1. Rotate the knob clockwise or counter-clockwise 90 degrees to reverse lock.
  2. Rotate 90 degrees in the opposite direction to unlock.

6. Maintenance

  • Regularly check the battery level and replace all 8 AA batteries when prompted by a low battery alert. Use original batteries for optimal performance and to prevent leakage.
  • Keep the fingerprint sensor and keypad clean and free from dust or debris. Use a soft, dry cloth for cleaning.
  • Avoid exposing the lock to extreme temperatures or humidity.
  • Do not use abrasive cleaners or solvents on the lock's surface.
  • Ensure the door and door frame are in good condition to prevent misalignment or excessive force on the lock.
  • If the lock is not in use for an extended period, remove the batteries to prevent leakage.

7. Troubleshooting

ProblemPossible CauseSolution
Lock keeps sounding an alarm (false alarm) Sensor malfunction, environmental interference, or software glitch. First, try a soft reset by removing and reinserting the batteries. If the issue persists, a factory reset may be necessary. Ensure the door is properly closed and aligned.
Door does not lock/unlock properly Low battery, misalignment of lock body/strike, obstruction, or mechanical failure. Check battery level and replace if low. Inspect door alignment and ensure no obstructions. Verify the lock body and strike plate are correctly installed.
Fingerprint/Password not recognized Incorrect input, dirty sensor/keypad, or unregistered data. Ensure correct fingerprint placement or password entry. Clean the sensor/keypad. Re-register fingerprint/password if necessary.
Bluetooth connection issues Out of range, interference, or APP/firmware issues. Ensure you are within 10m of the lock. Check for physical obstructions. Restart the APP and/or the lock. Update APP/firmware if available.
Low battery warning Batteries are running low. Replace all 8 AA batteries immediately. Use original batteries.

Product Performance Fault Table

The following are common performance faults:

  • Surface cracks due to structural or material factors.
  • Mechanical structure failure.
  • Control function failure.
  • Bluetooth connection failure.
  • Keypad failure.

8. User Tips

  • Factory Reset as Last Resort: If you experience persistent issues like continuous alarms, a factory reset can often resolve software glitches. However, be aware that this will erase all user data and settings, requiring you to reconfigure the lock from scratch.
  • Emergency Key Storage: Always keep your emergency keys in a safe, accessible location outside your home, but not easily discoverable by others. This is crucial in case of battery failure or electronic malfunction.
  • Regular Battery Checks: Even without a low battery alert, it's good practice to check battery levels periodically, especially if you use the lock frequently or during colder months when battery performance can decrease.
  • Professional Installation: For optimal performance and security, consider professional installation. Incorrect installation can lead to malfunctions and compromise the lock's security features.

9. Warranty and Support

This product's after-sales service strictly adheres to the "Consumer Rights and Interests Protection Law of the People's Republic of China" and the "Product Quality Law of the People's Republic of China".

Warranty Policy

During the warranty period, you can enjoy free return, exchange, or repair services according to these regulations. Returns, exchanges, and repairs must be processed with a valid invoice.

Service TypeService Policy
ReturnWithin 7 days from the date of receipt for quality-related reasons.
ExchangeWithin 15 days from the date of receipt for quality-related reasons.
RepairWithin 3 years from the date of receipt for quality-related reasons.

Friendly Reminder: Due to the need for packaging to ensure product safety during transportation, it is recommended to keep the packaging box for at least 30 days from the date of receipt.

Non-Warranty Clauses

  • Unauthorized repair, misuse, collision, negligence, abuse, liquid ingress, accident, alteration, incorrect use of non-product accessories, or tearing/altering labels, anti-counterfeit marks.
  • Exceeded the three-guarantee period.
  • Damage caused by force majeure.
  • Does not meet the conditions of the "Product Performance Fault Table".
  • Product and its accessories generate performance faults due to human factors.

Support Contact Information

  • Service Hotline: 400-990-7930 (Working days 10:00-18:00)
  • Service Website: www.aqara.com/support
  • Service Email: support@aqara.com
  • Official WeChat Account: Search for "绿米智慧生活"
  • Manufacturer: Shenzhen Lumi United Technology Co., Ltd.
  • Address: 8th Floor, Jinqi Zhigu Building, Tangling Road No.1, Taoyuan Street, Nanshan District, Shenzhen City
  • Product Information Website: www.aqara.com

10. Important Notes

  • This product communicates with iPhone, iPad, or iPod via HomeKit technology.
  • The "Works with Apple HomeKit" badge means that this electronic accessory is designed to connect specifically to iPod touch, iPhone, or iPad, and has been certified to meet Apple's performance standards. Apple is not responsible for the operation of this product or its compliance with safety and regulatory standards.

© 2024 Aqara. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.