YSRSAI WT5

Contents

RGBCCT COB LED Strip Kit User Manual

Model: WT5 Controller, TL5 Remote

1. Introduction

Thank you for purchasing the RGBCCT COB LED Strip Kit. This kit provides versatile lighting solutions with RGB, Warm White, and Cold White color options, offering seamless control through Tuya Smart App, voice commands via smart speakers, and an RF remote control. This manual will guide you through the installation, operation, and maintenance of your LED strip lighting system.

2. Safety Information

  • Read all instructions carefully before beginning installation.
  • When installing the battery in the remote, pay attention to the positive and negative polarity.
  • If the remote control will not be used for a long time, remove the battery.
  • If the remote distance becomes shorter or the remote becomes insensitive, replace the battery.
  • If there is no response from the receiver, re-match the remote.
  • Gently handle the remote; beware of falling.
  • For indoor and dry location use only.
  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. DO NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.
  • Compatible battery type is CR2032 and the nominal battery voltage is 3V.
  • Non-rechargeable batteries are not to be recharged.
  • Do not force discharge, recharge, disassemble, heat above 55°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
  • Ensure the batteries are installed correctly according to polarity (+ and -).
  • Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always securely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

3. Package Contents

Your kit may vary based on the length purchased (5M, 10M, or 20M), but typically includes:

  • RGBCCT COB LED Strip (5M, 10M, or 20M roll)
  • WT5 5-in-1 LED Controller (Tuya WiFi + RF)
  • LED Power Supply (e.g., 60W, 100W, 200W depending on strip length)
  • TL5 Touch Panel RF Remote Control (Optional, may be included in some kits)
20M Full Kit components including LED strip, controller, power supply, and remote.
Figure 3.1: Example of a 20M Full Kit with LED strip, controller, power supply, and remote.
5M Strip Set components including LED strip, controller, power supply, and remote.
Figure 3.2: Example of a 5M Strip Set with LED strip, controller, power supply, and remote.

4. Specifications

FeatureSpecification
Brand NameYSRSAI
Model Number (LED Chip)SMD3014
Item TypeStrip
Strip TypeCOB
LEDs Number/M840led/m
Power Consumption (W/m)11.52W/m (or 14W/m)
VoltageDC 24V
Power SourceDC
Color Temp(K)RGB+W+WW (RGBCCT+CRI 90)
Luminous Flux2000-82000
Average Life (hrs)50000h
WaterproofNo
Is Smart DeviceYes (Tuya WiFi, RF 2.4GHz)
CertificationCCC, CE, GS
LED Width12mm
Controller SizeL120 x W43 x H27mm
Controller Input Voltage12-24VDC
Controller Input Current15.5A
Controller Output Current5CH, 3A/CH
Controller Dimming Range0-100%
Controller Dimming Gray Scale4096 (2^12) levels
Controller PWM Frequency1000Hz (default)
RF Control Distance30m (barrier-free space)
Power Supply Sizes60W: 140*50*23mm, 100W: 140*50*23mm, 200W: 180*50*23mm

5. Installation

5.1 LED Strip Installation

  • The COB LED strip features double-sided adhesive tape for easy installation.
  • The strip is 12mm wide and bendable, allowing it to be shaped as desired.
  • It is cuttable at designated marks; the rest of the LED strip will continue to function normally.
COB LED strip features: double-sided tape, bendable, and cuttable.
Figure 5.1: COB LED Strip features: Double-sided Tape, Bendable, Cuttable.

5.2 WT5 5-in-1 LED Controller Wiring

The WT5 controller supports RGB, RGBW, RGB+CCT, CCT, or single color LED strips. Ensure correct wiring according to your LED strip type.

WT5 5-in-1 LED Controller diagram showing input and output terminals for various LED strip types.
Figure 5.2: WT5 5-in-1 LED Controller Diagram.

System Wiring Diagram

System wiring diagram for WT5 controller showing connections for mobile phone, WiFi router, Amazon Echo, RF remote, and various LED controllers.
Figure 5.3: System Wiring Diagram.

Notes for System Wiring:

  • The above distances (e.g., 30m for RF, 15m for WiFi) are measured in a spacious (no obstacle) environment. Refer to actual test distances before installation.
  • Ensure your WiFi router operates on the 2.4GHz band; the 5GHz band is not supported. Do not hide your router network.
  • Keep the distance between WT5 devices and the router close, and check WiFi signals for optimal performance.

5.3 Power Supply Wiring

The LED power supply features instant, tool-free wiring for effortless connection.

LED Power Supply with input and output connector labeling.
Figure 5.4: LED Power Supply with Input and Output Connector Labeling.

5.4 TL5 Touch Panel RF Remote Control Installation

The TL5 remote control can be installed in three ways:

  1. Fix it on the wall with two screws.
  2. Adhere it to the wall with paste.
  3. The panel can be adsorbed directly onto metal surfaces.
TL5 Touch Panel RF Remote Control mechanical structures and installation diagram.
Figure 5.5: TL5 Touch Panel RF Remote Control Mechanical Structures and Installation.

Note for TL5 Installation:

  • Before first use, remove the protective film from the battery.
  • Open the battery cover with a screwdriver.
  • If the LED indicator is not on when pressing a key, it may be due to a dead battery or bad contact caused by multiple plugging. Replace the battery or raise the battery shrapnel with a screwdriver.

6. Operation

6.1 Control Methods Overview

Your LED lighting system can be controlled in three primary ways:

  • App Control: Using the Tuya Smart or Smart Life app on your mobile device.
  • Third-Party Voice Control: Compatible with Amazon Alexa, Google Assistant, Tmall Genie, and Xiaodu smart speakers.
  • 2.4GHz Remote Control: Using the included TL5 Touch Panel RF Remote Control.
Diagram showing three ways to control the LED light: App Control, Third Party Voice Control, and 2.4GHz Remote Control.
Figure 6.1: Three Ways to Control Your LED Light.

6.2 Tuya Smart App Network Connection

To enable smart control features, you need to connect your WT5 controller to the Tuya Smart or Smart Life app.

Download and Open App

  1. Search for "Tuya Smart" or "Smart Life" in your app store (Google Play Store or Apple App Store) or scan the QR code provided in the product packaging.
  2. Download and install the app.
  3. Register and log in after installation.

App Pairing Network (WiFi Configuration)

There are two methods to enter WiFi config mode:

  1. Method 1 (Fast Pairing): Press the Match/Set key on the WT5 controller twice quickly. The RUN LED indicator will flash rapidly, and the output LED will flash 10 times, indicating it's in WiFi config mode.
  2. Method 2 (Long Press): Press and hold the Match/Set key for 5 seconds. The RUN LED indicator will flash rapidly, and the output LED will flash 10 times, indicating it's in WiFi config mode.

Once in WiFi config mode, open the Tuya Smart app, and it should automatically detect the WT5 device. Follow the in-app instructions to add the device. Ensure your phone is connected to the same 2.4GHz WiFi network as the controller.

Video 6.1: WT5 Network Operation Demonstration. This video shows how to connect the WT5 controller to the Tuya app and control the LED strip.

If the Tuya Smart App network connection succeeds, the RUN LED indicator will stop flashing, and turn to the corresponding light type color (White: DIM, Yellow: CCT, Red: RGB, Green: RGBW, Blue: RGB+CCT). You can then find the device in the Tuya Smart App.

Bluetooth Control (New Versions)

New versions of WT5, WT1, and V5-L(WT) controllers include Bluetooth control. This allows you to control the lights via Bluetooth even if the network connection is poor or disconnected. However, note that before WiFi configuration, you cannot directly control the lamp with Bluetooth.

6.3 Tuya Smart App Interface

The Tuya Smart App provides various interfaces for controlling your LED strip:

  • White Interface (for DIM type): Touch the brightness slider to adjust brightness.
  • Color Temperature Interface (for CCT type): Touch the color wheel to adjust color temperature, and the brightness slider to adjust brightness.
  • Color Interface (for RGB or RGBW type): Touch the color wheel to adjust static RGB color, brightness slider for color brightness, and saturation slider for color saturation (gradient from current color to white).
  • Scene Interface: Pre-set scenes (1-4 are static colors, 5-8 are dynamic modes like green fade, RGB jump, etc.).
  • Music, Timer, Schedule: Music play can use your phone's music player or microphone. The Timer key can turn on/off the light within 24 hours. The Schedule key allows adding multiple timers for on/off at different periods.
Tuya App control interface examples showing color wheel, brightness, and timer settings.
Figure 6.2: Tuya App Control Interface.

6.4 WT5 Match Remote Control (Optional)

If you have an RF 2.4G remote control (like the TL5 touch panel), you can pair it with the WT5 controller.

Matching the WT5 with a Remote

There are two methods for matching:

  1. Using the WT5's Match Key: Short press the Match/Set key on the WT5. Immediately press the on/off key (for single zone remote) or a zone key (for multiple zone remote) on the remote. The LED indicator will flash a few times, indicating successful matching.
  2. Using Power Restart: Switch off the power to the WT5, then switch it on again. Immediately short press the on/off key (for single zone remote) or a zone key (for multiple zone remote) 3 times on the remote. The light will blink 3 times, indicating successful matching.

Deleting Matched Remotes from WT5

There are two methods for deleting matched remotes:

  1. Using the WT5's Match Key: Press and hold the Match/Set key on the WT5 for 20 seconds. The LED indicator will flash a few times, indicating all matched remotes were deleted.
  2. Using Power Restart: Switch off the power to the WT5, then switch it on again. Immediately short press the on/off key (for single zone remote) or a zone key (for multiple zone remote) 5 times on the remote. The light will blink 5 times, indicating all matched remotes were deleted.

6.5 WT5 Work as WiFi-RF Converter

The WT5 controller can also function as a WiFi-RF converter, allowing the Tuya Smart App to control one or more RF LED controllers or RF LED dimming drivers synchronously.

Matching the Controller with Tuya App

  1. Using the Controller's Match Key: Short press the Match/Set key of the RF controller. Immediately press the on/off key on the Tuya Smart App. The LED indicator will flash a few times, indicating successful matching.
  2. Using Power Restart: Switch off the power to the RF controller, then switch it on again. Immediately short press the on/off key 3 times on the Tuya Smart App. The light will blink 3 times, indicating successful matching.

Deleting Matched Controllers from Tuya App

  1. Using the Controller's Match Key: Press and hold the Match/Set key of the RF controller for 5 seconds. The LED indicator will flash a few times, indicating the match was deleted.
  2. Using Power Restart: Switch off the power to the RF controller, then switch it on again. Immediately short press the on/off key 5 times on the Tuya Smart App. The light will blink 5 times, indicating the match was deleted.

6.6 TL5 Touch Panel RF Remote Control Functions

TL5 Touch Panel RF Remote Control with LED indicator light.
Figure 6.3: TL5 Touch Panel RF Remote Control with LED Indicator Light.
TL5 Remote Control interface showing RGB color slider, color temperature slider, brightness slider, and 4 scene/zone keys.
Figure 6.4: TL5 Remote Control Key Functions.
  • Short press dynamic mode key: Switches dynamic mode.
  • Long press dynamic mode key (2s): Adjusts speed (10 levels).
  • On/Off button: Powers the lights on or off.
  • RGB Color Slider: Adjusts RGB colors.
  • Color Temperature Slider: Adjusts warm white to cold white.
  • Brightness Slider: Adjusts light brightness.
  • 4 Scene or 4 Zone Keys: Allows setting up to 4 scenes or controlling 4 separate zones.

4 Scene or 4 Zone Setup (TL1/TL2/TL4/TL5)

The remote can be set as a single zone 4-scene remote control (factory default) or a 4-zone remote control.

  • To set as single-zone 4-scene remote control: Long press the power button and the 'Zone 1' key at the same time for 5 seconds. The red indicator blinks 3 times.
  • To set as 4-zone remote control: Long press the power button and the 'Zone 4' key at the same time for 5 seconds. The red indicator blinks 3 times.

Scene and Zone Key Functions

  • Scene Function:
    • Short press a scene key to call up the scene.
    • Long press a scene key for 5 seconds to save the current state to the scene. The red LED indicator flashes once when saved successfully.
  • Zone Function:
    • Short press a zone key to turn on the zone light and select this zone.
    • Quickly short press the zone key to select multiple zones at the same time.
    • Long press a zone key for 2 seconds to turn off the zone lights.

Scene Lock

The scene keys can be set to a locked status, cancelling the long press for 5s to save the scene function (default is not locked).

  • To lock: Short press the panel on/off key, turn on the light first, then turn off the light. Immediately long press the panel on/off key for 5s, and then immediately long press any one scene key for 5s to set all scene keys to lock status.
  • To unlock: Short press the panel on/off key, turn on the light first, then turn off the light. Immediately long press the panel on/off key for 5s, then immediately long press any one scene key for 10s to set all scene keys to unlocked state.

6.7 Dynamic Mode List

The controller offers various dynamic modes for RGB/RGBW and RGB+CCT light types:

For RGB/RGBW:

No.NameNo.Name
1RGB jump6RGB fade in and out
2RGB smooth7Red fade in and out
36 color jump8Green fade in and out
46 color smooth9Blue fade in and out
5Yellow cyan purple smooth10White fade in and out

For RGB+CCT:

No.NameNo.Name
1RGB jump6RGB fade in and out
2RGB smooth7Red fade in and out
36 color jump8Green fade in and out
46 color smooth9Blue fade in and out
5Color temperature smooth10White fade in and out

7. Maintenance

  • Keep the LED strip and controller clean and dry.
  • Avoid exposing the components to extreme temperatures or humidity.
  • Do not use harsh chemicals or abrasive cleaners on the LED strip or controller.
  • Regularly check all connections to ensure they are secure.

8. Troubleshooting

  • Lights not turning on:
    • Check all power connections to ensure they are secure.
    • Verify the power supply is receiving power and functioning correctly.
    • Ensure the LED strip is correctly wired to the controller (polarity and channel).
    • If using the remote, check its battery and re-match if necessary.
  • Incorrect colors or flickering:
    • Check the wiring between the LED strip and the controller for any loose connections or incorrect channel assignments.
    • Ensure the correct light type is set in the Tuya App and on the controller (if applicable).
  • App control issues:
    • Ensure your WiFi router is on the 2.4GHz band and the signal is strong near the controller.
    • Re-attempt the Tuya Smart App network connection process.
    • If WiFi is poor, try controlling via Bluetooth (for new versions of WT5).
    • Restart your router, controller, and mobile device.
  • Remote control not responding:
    • Check the battery in the remote (CR2032, 3V).
    • Re-match the remote with the WT5 controller as described in Section 6.4.
    • Ensure there are no metal objects or obstacles within 20cm of the remote or controller that could interfere with the RF signal.

9. User Tips

  • For optimal heat dissipation and product lifespan, ensure the LED strip and controller are not stacked and maintain a distance of at least 20cm from other objects.
  • Avoid installing the product close to a switching power supply (within 20cm) to prevent radiation interference.
  • For best remote control reception, install the controller at least 1 meter from the floor.
  • When using RGB+CCT or CCT light types, quickly power cycling the light (on/off) will cycle through 3 levels of color temperature (Warm White, Neutral White, Cold White).
  • To quickly change the light on/off fade time between 3 seconds and 0.5 seconds, switch off the power, then switch on, and immediately short press the match key 3 times.

10. Warranty & Support

This product comes with a 5-year warranty. For any issues or support, please contact the seller or refer to the official product page for further assistance.

You can also find additional item guides and documents, including a user manual in PDF format, by visiting the product page or contacting customer support.

© 2024 YSRSAI. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.