1. Introduction
The SONGGER TA521A and TA522A Paint Coating Thickness Gauges are portable instruments designed for measuring the thickness of non-metallic coatings on metal substrates. The device automatically identifies ferrous and non-ferrous substrates and applies the appropriate measurement principle. It is suitable for automotive paint inspection, industrial coating measurement, and quality control of metal surface treatments. The compact design and rotatable display allow convenient operation in various inspection environments.
2. Safety Information
WARNING:
- Improper use of the instrument may result in inaccurate measurements or equipment damage.
- Do not attempt to disassemble or modify the device.
- Avoid impact or dropping of the instrument as it may damage the internal sensor.
- Keep out of reach of children.
- Proper disposal: Follow WEEE directives for electronic waste.
Note: This warning information is for reference only. Final warning language must comply with the official language requirements of the destination country.
3. Product Overview
The TA52 series coating thickness gauge is a robust and precise tool for various measurement tasks. It features automatic substrate recognition and a 180° rotatable display for convenience.
The device is designed for both professional and home use, providing accurate readings on various metal surfaces.
4. Specifications
| Feature | Specification |
|---|---|
| Model | TA521A/TA522A |
| Power Supply | 2 x 1.5V AAA batteries |
| Rated Voltage | 3V DC |
| Dimensions | 104 x 57 x 26 mm |
| Weight | Approximately 70 g (without batteries) |
| Measurement Principle | Magnetic induction (ferrous) and eddy current (non-ferrous) |
| Compatible Substrates | Iron, aluminum, zinc, and other metal substrates with non-metallic coatings |
| Measuring Range | 0 to 2000 µm, 0 to 2 mm, 0 to 78 mil |
| Accuracy | ±(3% + 1 µm), ±(3% + 0.001 mm), ±(0.117% + 0.039 mil) |
| Resolution | 0.1 µm (below 100 µm), 1 µm (100 µm or above) |
| Display | Four digit LCD with max value 8888, 180° screen rotation |
| Measurement Speed | Up to two measurements per second |
| Calibration Method | Zero point calibration |
| Unit Selection | µm, mm, mil |
| Over-range Indication | "OL" displayed on screen |
| Iron Powder Putty Range | 0 to 1000 µm |
| Galvanized Iron Measurement Range | 3 to 500 µm |
| Minimum Curvature Radius (Convex) | 5 mm |
| Minimum Curvature Radius (Concave) | 25 mm |
| Minimum Measuring Area | Diameter 15 mm |
| Minimum Substrate Thickness (Ferrous) | 0.30 mm |
| Minimum Substrate Thickness (Non-ferrous) | 0.05 mm |
| Operating Environment Temperature | -10°C to 50°C |
| Operating Environment Humidity | Not exceeding 90% relative humidity |
| Operating Environment Altitude | Below 2000 m (indoor use only) |
5. Setup
5.1 Battery Installation
- Open the battery compartment.
- Install two 1.5V AAA batteries according to the polarity markings inside the compartment.
- Close the battery compartment securely.
5.2 Initial Preparation
- Ensure the probe surface is clean and free from dust or oil before measurement.
- Turn on the device using the power button.
6. Operation
6.1 Measurement Procedure
- Place the probe vertically on the coated metal surface.
- The instrument will automatically detect whether the substrate is ferrous or non-ferrous and perform the measurement.
- Ensure stable contact between the probe and the surface during measurement for accurate readings.
6.2 Data Reading
- The measured coating thickness will appear on the display screen.
- To change the measurement unit (µm, mm, or mil), use the unit selection function on the device.
- If the measurement exceeds the specified range, the display will show "OL".
6.3 Calibration
For improved accuracy, perform zero calibration before measurement. To do this, place the probe on an uncoated metal substrate of the same material type as the one you intend to measure.
7. Precautions
- Use only the specified battery type and ensure correct polarity during installation.
- Do not use the instrument in environments with strong electromagnetic interference.
- Avoid contact between the probe and rough or contaminated surfaces that may affect measurement accuracy.
- Do not expose the instrument to extreme temperatures, high humidity, or corrosive environments.
8. Storage and Maintenance
8.1 Cleaning
- Keep the probe clean and free of debris after each use.
- Wipe the exterior with a soft, dry cloth. Do not use solvents or abrasive cleaners.
8.2 Storage
- Store the device in a dry environment within the specified storage temperature range (-20°C to 60°C).
- Remove batteries if the instrument will not be used for an extended period to prevent leakage and internal damage.
9. Troubleshooting
- No Power: Check battery installation and ensure batteries are not depleted. Replace if necessary.
- Inaccurate Readings: Ensure the probe surface is clean. Perform a zero calibration on an uncoated substrate of the same material. Avoid strong electromagnetic interference.
- "OL" Displayed: The measurement is outside the device's specified range (0-2000 µm).
- Unstable Readings: Ensure stable and vertical contact between the probe and the surface during measurement.
10. User Tips
Users have found this gauge to be effective for home projects, providing quick and accurate readings. For best results, always ensure the surface and probe are clean before use.
11. Compliance Disclaimer
This document is provided for product instruction purposes only. It does not constitute legal advice. The seller is responsible for ensuring compliance with destination market regulations.
12. Warranty and Support
For warranty information, technical support, or any inquiries regarding your SONGGER TA52 Digital Paint Thickness Gauge, please contact your seller or refer to the official product documentation. A detailed user manual in PDF format is available for download: User Manual (PDF).