Tuya Smart Soil Tester

Contents

Tuya ZigBee Smart Soil Tester Instruction Manual

Monitor soil temperature and humidity with smart home integration.

1. Product Overview

The Tuya ZigBee Smart Soil Tester is designed to monitor soil temperature and humidity, providing essential data for plant care. It integrates with smart home platforms like Alexa and Google Assistant, and can be controlled via the Tuya Smart or Smart Life app. The device features an IP66 waterproof rating, making it suitable for outdoor use.

Tuya ZigBee Smart Soil Tester with app interface showing moisture and temperature

Figure 1: Smart Soil Tester and its mobile application interface.

Video 1: Overview of the Zigbee Smart Soil Sensor, including setup and app integration.

2. Specifications

FeatureSpecification
BatteryAA 1.2V 3 Ni-MH battery (Rechargeable)
Solar Charging Current35mA
Communication ProtocolZigbee 3.0
Wireless ProtocolZigbee IEEE 802.15.4
Wireless Distance50M
Waterproof LevelIP66
Temperature Detection Range-10~60°C (14°F~140°F)
Moisture Detection Range0-100%RH (Non-Condensing)
Electrical Conductivity Detection RangeMaximum 20ms/cm
Temperature Detection Accuracy0.5°C (Adjustable)
Moisture Detection Accuracy5%RH (Adjustable)
Electrical Conductivity Detection Accuracy3%FS, 0.01ms/cm
Time Span of Detection10min (Adjustable)
Working Temperature-10~60°C (14-140°F)
Working Humidity0-100%RH (Non-Condensing)
Size78mm X 78mm X 146mm

3. Installation and Setup

3.1. Battery Installation

  1. Remove the waterproof rubber plug from the battery compartment.
  2. Use a screwdriver to unscrew the screws on the battery compartment cover.
  3. Remove the cover and battery compartment.
  4. Insert the 3 AA 1.2V Ni-MH rechargeable batteries, paying attention to the positive and negative poles as marked.
  5. Replace the battery compartment cover and tighten the screws.
  6. When installing waterproof plugs, ensure the sloping side faces upwards to prevent leakage.

3.2. Device Insertion into Soil

Before inserting the device, remove the probe protective sleeve.

  • Correct Demonstration: Insert the probes fully into the soil.
  • Error Demonstration: Avoid inserting probes partially or at an angle.
  • Error Demonstration: Ensure probes do not touch stones, the bottom, or the rim of a container. The probes should be fully submerged in the soil.
Installation and Use diagram showing battery installation steps and correct/error probe insertion

Figure 2: Battery installation and proper probe insertion techniques.

3.3. App Download and Registration

  1. Download App: Scan the QR codes below or search for "Tuya Smart" or "Smart Life" in your device's application market (Google Play for Android, Apple Store for iOS).
    QR codes for Tuya Smart and Smart Life apps

    Figure 3: QR codes for downloading the Tuya Smart or Smart Life app.

  2. Register and Login:
    • Launch the "Smart Life" app.
    • To register, enter your mobile phone number or email address, create a password, then log in.
    • If you already have an account, simply log in.

4. App Integration (Add Device Steps)

The soil tester requires a ZigBee gateway for smart home integration. Ensure your gateway is set up first.

  1. Add ZigBee Gateway: Add your Tuya ZigBee gateway to the app by following its specific instructions (distinguish between wired and wireless gateways).
  2. Add Soil Tester (Sub-device):
    • Ensure the soil tester is in pairing mode (flashing indicator). If not, press and hold the reset button for about 5 seconds until the LED flashes.
    • In the app, navigate to your ZigBee gateway and select "Add Device" or search for nearby devices.
    • The app should discover the soil tester. Follow the on-screen prompts to add it.

5. Operation

5.1. Monitoring Soil Conditions

Once connected, the app will display real-time soil moisture and temperature readings. You can view current data and historical records.

App interface showing remote control and current soil conditions

Figure 4: Remote monitoring of soil conditions via the app.

5.2. Voice Control

Integrate with Amazon Alexa or Google Home for voice commands. For example:

  • "Alexa, what's the soil temperature now?"
  • "Google, what's the moisture level of the soil now?"
Voice control demonstration with Alexa and Google Home

Figure 5: Voice control functionality with smart assistants.

5.3. History Records

The app provides historical data for electrical conductivity, moisture, and temperature, allowing you to track changes daily, monthly, and yearly.

App interface showing history records for soil data

Figure 6: Viewing historical data in the app.

6. Functions and Settings

6.1. Parameter Settings

  • Temperature Unit: Switch between Celsius and Fahrenheit.
  • Temperature Sensitivity: Set the temperature change value that triggers a report (range: 0.5°C to 3°C / 32.9°F to 37.4°F).
  • Moisture Sensitivity: Set the moisture change value that triggers a report (range: 1% to 5%).
  • High Temperature Alarm: Set the upper limit for temperature alerts (range: -10°C to 60°C / 14°F to 140°F).
  • Low Temperature Alarm: Set the lower limit for temperature alerts (range: -10°C to 60°C / 14°F to 140°F).
  • High Moisture Alarm: Set the upper limit for moisture alerts (range: 0% to 100%).
  • Low Moisture Alarm: Set the lower limit for moisture alerts (range: 0% to 100%).
  • Detection Interval Time: Adjust how often the device detects and reports data (range: 5 minutes to 60 minutes).

6.2. Scene Linkage

Create automated scenes within the app. For example, you can set a rule: "If soil moisture is detected to be below 30%, then turn on the watering switch for 5 minutes." The device supports scene linkage even if the gateway is disconnected, provided multiple devices under the same gateway have been set up for scene linkage.

6.3. Device Sharing

The Zigbee device can be shared with other family members through the app, allowing multiple users to monitor and control the soil tester.

App interface showing device sharing with family

Figure 7: Sharing the device with family members.

7. Maintenance

  • Probe Cleaning: Regularly clean any soil or debris from the metal probes to ensure accurate and stable readings.
  • Solar Panel Charging: The device automatically charges its Ni-MH batteries via the solar panel when battery levels are low and sunlight is available.
  • Solar Panel Care: Ensure the solar panel is free from obstructions and regularly clean dust and dirt to maintain charging efficiency.

8. Troubleshooting (FAQ)

8.1. How to manually trigger a detection and report to the app?

Press the reset button on the device. It will immediately detect and report values to the app. The detection time is approximately 3 seconds.

8.2. What does a high moisture reading indicate?

When the device shows approximately 80% moisture, it indicates that the soil is very wet. Note that the device cannot reach 100% moisture in soil, as 0% moisture is defined as dry soil and 100% as being in water.

8.3. The device does not update new values to the app for a long time. Is this normal?

Yes, this is normal. If the device doesn't update for an extended period, it's likely because the data change is small and hasn't met the reporting sensitivity threshold set in the app. You can press the reset button to force an immediate update of temperature and moisture values.

8.4. Humidity values seem to be stuck to a fixed value.

If humidity values appear stuck, first ensure the probes are clean and properly inserted into the soil, not touching any hard objects or container edges. If the issue persists, try manually triggering a report by pressing the reset button. If the problem continues, check the battery level and ensure the device is within range of the ZigBee gateway.

9. User Tips

  • For garden lawn plants, it is generally suitable to start watering when soil moisture reaches 30%-40%. It is recommended to turn off watering when moisture reaches 60%-70%.
  • Always ensure the metal probes are clean and free of soil buildup to maintain accurate readings.
  • When installing the sensor in a flower bed, ensure a distance of at least 10cm between the sensor probes and any flower bed barriers to avoid affecting readings.
  • If using the sensor on a dense lawn, remove the grass layer where the sensor will be placed to ensure full contact between the probes and the soil.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.