Diymore AC 220V 500W PWM Motor Speed Controller Module

Contents

Diymore AC 220V 500W PWM Motor Speed Controller Module User Manual

Adjustable Speed Regulator Control Governor Switch with Switch Terminal

1. Introduction

The Diymore AC 220V 500W PWM Motor Speed Controller Module is a versatile electronic component designed for precise control of various electrical appliances. It supports a high-power design, allowing for stepless adjustment of motor speed, lighting intensity, voltage output, and temperature. Its compact design and integrated heat dissipation make it suitable for a wide range of industrial and household applications.

Diymore AC 220V 500W PWM Motor Speed Controller Module

Figure 1: Diymore AC 220V 500W PWM Motor Speed Controller Module

Video 1: Product overview and demonstration of the speed controller module.

2. Safety Information

  • High Voltage Warning: This module operates with AC 220V. Always exercise extreme caution when working with high voltage. Ensure power is disconnected before installation, wiring, or maintenance.
  • Professional Installation Recommended: If you are not familiar with electrical wiring, seek assistance from a qualified electrician.
  • Proper Insulation: Ensure all connections are properly insulated to prevent short circuits and electric shock.
  • Environmental Conditions: Do not expose the module to moisture, water, or extreme temperatures. Operate within specified environmental conditions.
  • California Proposition 65 Warning: ⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

3. Package Contents

  • 1 x AC 220V 500W PWM Motor Speed Controller Module

4. Setup

The module features a terminal block wiring design for straightforward installation. It uses a single-wire input and single-wire output configuration.

4.1 Wiring Instructions

  1. Ensure Power is OFF: Before making any connections, ensure that the main power supply to the electrical appliance is completely disconnected.
  2. Identify Terminals: The module has a green terminal block. One side is for input, and the other is for output.
  3. Series Connection: Connect the module in series within the electrical appliance circuit. This means the power supply line to your appliance will be interrupted, and the module will be inserted into that break.
  4. Input Connection: Connect one of the live (hot) wires from your AC 220V power source to one terminal of the module's input.
  5. Output Connection: Connect the other terminal of the module's output to the live (hot) input of your electrical appliance.
  6. Secure Connections: Ensure all wires are securely fastened within the terminal blocks to prevent loose connections, which can cause arcing or overheating.
  7. Insulate: Double-check that all exposed wires are properly insulated.
Terminal block with switch for wiring

Figure 2: Terminal block wiring design for single input/single output.

Method of Use showing front and back of PCB

Figure 3: Module front and back view, illustrating connection points for series wiring.

5. Operating Instructions

Once the module is correctly wired and power is restored, you can operate it using the integrated potentiometer knob.

  1. Power On: Turn on the main power supply to the electrical appliance.
  2. Adjusting Output: Rotate the potentiometer knob clockwise to increase the output (e.g., increase motor speed, brighten lights, raise voltage/temperature). Rotate it counter-clockwise to decrease the output.
  3. Stepless Adjustment: The module provides stepless adjustment, allowing for precise control over the connected device's operation.
Pressure and Speed Regulator knob

Figure 4: Potentiometer knob for stepless adjustment of pressure and speed.

6. Maintenance

The module is designed for long-term stable operation with minimal maintenance.

  • Heat Dissipation: The module features built-in heat dissipation aluminum fins to prevent overheating. Ensure these fins are not obstructed to allow for proper airflow.
  • Cleaning: Periodically, with power disconnected, gently clean any dust or debris from the module, especially around the heat sink, using a soft brush or compressed air.
  • Inspection: Occasionally inspect wiring connections for any signs of loosening or damage.
Built-in heat dissipation aluminium fins

Figure 5: Built-in heat dissipation aluminum fins for stable operation and extended lifespan.

7. Troubleshooting

If the module is not functioning as expected, consider the following:

  • No Output/No Control:
    • Check all wiring connections to ensure they are secure and correct (series connection).
    • Verify that the power supply to the appliance is active.
    • Ensure the connected appliance is within the module's power specifications (max 500W).
  • Intermittent Operation:
    • Inspect for any loose wires or damaged insulation.
    • Ensure the module is not overheating due to obstructed airflow to the heat sink.
  • Overheating:
    • Confirm the load does not exceed 500W.
    • Ensure adequate ventilation around the module.

8. Specifications

ParameterValue
Input VoltageAC 220V
Maximum Current4A
Maximum Power500W
Control TypePWM (Pulse Width Modulation)
Adjustment MethodStepless (Potentiometer Knob)
Wiring MethodTerminal (Single In / Single Out)
Dimensions (L x W x H)32mm x 26mm x 21.5mm (excluding potentiometer knob)
Heat DissipationBuilt-in Aluminum Fins
Product Specifications Diagram

Figure 6: Visual representation of product specifications.

Product Dimensions Diagram

Figure 7: Detailed dimensions of the speed controller module.

9. User Tips

No specific user tips were available from provided reviews or Q&A content for this product.

10. Compliance Information

California Proposition 65 Warning:

⚠ WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.