5-inch AHD CVBS IPS Car Monitor and Reverse Camera User Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your BYNCG 5-inch AHD CVBS IPS Car Monitor and optional High-mount Reverse Camera. Please read this manual thoroughly before use to ensure proper functionality and safety.

2. Safety & Warnings

Read all instructions before use to ensure safety and prevent damage.

Personal Protection:

• Always wear appropriate safety protective equipment such as goggles and gloves during operation.

Vehicle Stability:

• Ensure that the vehicle is parked on a flat, sturdy, and well-ventilated surface.
• Use a jack and safety stand for reliable support. Do not rely solely on the jack.

General Warnings:

• Keep the device and its cord out of reach of children under 3 years old.
• To avoid danger of suffocation, keep plastic bags away from babies and children. Do not use this bag in cribs, beds, carriages, or playpens. This bag is not a toy.

Professional Advice:

• This manual provides general guidance. Car maintenance requires professional knowledge, specialized tools, and experience.
• It is strongly recommended that you entrust the installation work to a qualified car maintenance technician.
• Incorrect installation may cause vehicle malfunctions, performance degradation, or serious safety accidents.

3. Package Contents

Please check the package contents against the list below. If any items are missing or damaged, contact customer support.

4. Specifications

5. Setup & Installation

This section outlines the general steps for installing the car monitor and optional reverse camera. For specific vehicle details, always refer to your vehicle's maintenance manual.

5.1. Preparation Before Installation

Tools and Materials:

• Ensure you have the vehicle's "User Manual", "Service Manual", necessary specialized tools (e.g., torque wrenches), and general-purpose tools.

Accessory Check:

• After unpacking, immediately check against the accessory list (Section 3) to ensure all parts are present and undamaged.

Old Parts Comparison (if replacing existing equipment):

• Carefully compare new parts with removed old parts to confirm consistency in size, shape, interface, and bolt hole positions.

5.2. Safety Preparation

1. Park the vehicle, apply the handbrake, and secure non-operating wheels with chocks.
2. Disconnect the negative cable of the battery first, then the positive cable, and properly isolate it to prevent electrical hazards.

5.3. Disassembly (if replacing existing equipment)

• Orderly Disassembly: Disassemble from the outside to the inside, from accessories to the main body. Properly store and label all bolts, nuts, clips, and small parts.
• Avoid Force: Use appropriate tools. If jamming occurs, check for hidden fixing points or buckles. Do not pry or pull forcibly.
• Handling Connections: For electrical connectors, press down the latch then pull out. For oil pipelines, clean the area around the connection and use a special tool to disassemble, preparing a container to catch the flowing oil.
• Clean Contact Surface: After removing old parts, clean the installation contact surface to ensure it is free of rust, oil stains, and residues of old sealing materials.

5.4. Installation of New Accessories

1. Replacement of Consumables: Damaged gaskets, sealing rings, O-rings, clamps, locknuts, etc., should be replaced with new ones during reassembly.
2. Standardized Tightening: Use a torque wrench to tighten bolts according to the sequence and torque values specified in the vehicle's maintenance manual. Typically, tighten bolts in a "crosswise, fractional, and progressive" manner.
3. Reliable Connection: Ensure all electrical plugs are fully inserted and locked. All oil and air pipes must be securely connected with clamps in the correct position.
4. Add Lubricant/Sealant: Apply the specified type of lubricating grease or sealant to designated locations (e.g., bearings, threads, sealing surfaces) as required by the manual.

5.5. Wiring Diagram

Refer to the following diagram for proper wiring connections for the monitor and optional high-mount reverse camera.

Monitor Connections:

• Power Cable: Connect to vehicle's power supply.
• CH1 / CH2: Video input channels. Connect video cables from cameras here.
• Trigger Wire: Connect to the reverse light signal for automatic display switching when reversing.

Camera Connections (Optional):

• Power Cable: Connect to the vehicle's reverse light (GND and Reverse light +).
• Out: Video output, connects to CH1 or CH2 on the monitor via the 10M Video Cable.
• Trigger Wire: Connect to the same reverse light signal as the monitor's trigger wire.

5.6. Installation Location & Brackets

The high-mount reverse camera is designed for vehicles like Mercedes Benz Viano, Sprinter, Vito, VW, and RVs, typically installed at the rear high-mount position to provide a wide 170° view.

The monitor offers two installation methods using distinct brackets:

6. Operation

6.1. Monitor Controls

The monitor features three buttons on the back for chroma adjustment and menu navigation.

• Increase key (+): Used to increase values or navigate up in menus.
• Hue/Brightness/Contrast: This button cycles through adjustment modes for hue, brightness, and contrast. Press to select a mode, then use the +/- keys to adjust.
• Reduction key (-): Used to decrease values or navigate down in menus.

6.2. Display Features

AHD vs CVBS Quality:

The monitor supports both AHD (Analog High Definition) and CVBS (Composite Video Broadcast Signal) inputs. AHD offers significantly clearer and higher resolution video compared to traditional CVBS.

IPS Full Viewing Angle:

The IPS screen provides a full viewing angle with realistic color reduction and 500cd brightness, ensuring clear visibility from various positions.

Live Effect Display (Day & Night Vision):

The system provides clear images in various lighting conditions, including day, night (dark environment), night (light environment), and underground garages.

6.3. Parking Line Adjustment

The parking lines displayed on the monitor are adjustable via the monitor's menu settings.

7. Maintenance & Storage

7.1. Post-Installation Inspection and Testing

After installation, perform the following checks:

Visual and Manual Inspection:

• Confirm all components are installed correctly.
• Ensure no tools or parts are left in the engine compartment or work area.

Phased Testing (Crucial):

• Static Test (Vehicle Off): Restore battery connection. Turn on power, check dashboard for fault lights, and test relevant electrical functions (e.g., lights, switches).
• Idle Test (Engine On): Start the engine. Observe for abnormal noise, vibration, oil leakage, water leakage, or air leakage. Check instrument panel data for normal operation.
• Dynamic Road Test (Cautiously): Conduct low-speed tests on a closed, safe, and legal road section. First, test basic functions like braking and steering. Gradually test functions related to newly replaced parts.

7.2. Break-in Period

Some components may require a break-in period for optimal performance. Avoid aggressive driving during this initial stage.

7.3. Regular Inspection

It is recommended that a qualified technician review your installation work during the first maintenance after installation.

8. Troubleshooting

Fault Symptoms:

If any of the following symptoms occur after installation, immediately stop using the vehicle and contact a professional technician for troubleshooting:

• Abnormal noise
• Warning lights illuminate
• Fluid leaks
• Unusual odors
• Performance decreases

9. User Tips

Based on common user experiences, here are some tips for optimal use:

• Ensure all cable connections are secure and properly insulated to prevent interference or short circuits.
• Regularly clean the camera lens to maintain clear visibility, especially in adverse weather conditions.
• Familiarize yourself with the monitor's adjustable menu to customize brightness, contrast, and parking line settings to your preference.
• When installing the camera, consider its IP68 waterproof rating, but avoid direct high-pressure water jets during cleaning to prolong its lifespan.

10. Warranty & Support

For detailed warranty information and further support, please refer to the complete user manual PDF available at the seller's page or contact the manufacturer directly. The PDF can be found at User manual (PDF).

Manufacturer Information:

• Company Name: Yiwu Yuet top e-commercelimite
• Address: Room 401, No. 1, Building 7, Zongtang Second District, Jiangdong Street, Yiwu City, Zhejiang Province
• Email: 517636919@qq.com
• Responsible Person: MoRuChao
• Phone: +86-13631860484

EU Representative Information:

• Company Name: MJCM SARL
• Address: 78 avenue des Champ-Elysees Bureau 326 Paris Ile-de-France
• Email: mjcm190928@gmail.com
• Phone: 0033767213611

This product is CE certified.