IKSLED Microwave radar sensor

Contents

Microwave Radar Human Body Sensor Switch Instruction Manual

Brand: IKSLED | Model: Microwave radar sensor

1. Introduction

This manual provides detailed instructions for the installation, operation, and troubleshooting of your IKSLED Microwave Radar Human Body Sensor Switch. This 5.8G radar detection module is designed for automatic on/off control of LED lights, operating within a DC3.7-24V range with a 3A current capacity. Please read this manual carefully before use to ensure proper function and safety.

2. Safety Information

WARNING: Please strictly follow the instructions, safety tips, and use the product with caution.

  • Ensure the power supply matches the specified voltage (DC 3.7-24V) and current (3A) requirements of the sensor switch and connected LED lights.
  • Do not use this sensor for controlling motors, solenoid valves, solar lights, constant current lamps, or other incompatible equipment.
  • Incorrect wiring, such as reversed input/output or positive/negative poles, can lead to malfunction or damage. Always refer to the wiring diagram.
  • Avoid installing the sensor in locations where it might be exposed to extreme temperatures, moisture, or direct sunlight, which could affect performance.

3. Specifications

Attribute Value
Brand Name IKSLED
Model Number Microwave radar sensor
Product Name Radar human body induction sensor
Switch Type Sensor Switch
Voltage DC 3.7-24V
Max Current 3A
Material Plastic
Induction Method 360° induction
Max Induction Distance 6-8m
Induction Delay 30s (infinitely added with continued activity)
EU LVD Voltage Low voltage: Below 50Vac or 75Vdc
Certification RoHS, LVD, EMC, CE
Is Smart Device No
Origin Mainland China

4. Setup Instructions

4.1. Identifying the Sensing Surface

The sensor module has a designated sensing surface. Ensure this side faces the area where motion detection is desired for optimal performance.

Diagram showing the sensing surface of the radar module
Figure 1: The surface marked 'Sensing surface' is the active detection area.

4.2. Wiring

Proper wiring is crucial for the sensor's functionality. Refer to the specific wiring diagram for your sensor type (Silicone wire, 55-21 DC Wire, or USB Wire).

General Wiring Steps:

  1. Connect the LED light to the sensor switch first.
  2. Then, connect the power supply to the sensor switch.

Max Load Capacity:

  • 3V: >5W
  • 3.7V: >7W
  • 5V: >12W
  • 12V: >36W
  • 24V: >48W
Wiring diagram for Silicone wire sensor, showing V-, V+, L-, L+ connections
Figure 2: Example wiring for a Silicone wire sensor. V+ and V- are power input, L+ and L- are light output.
USB wire variant of the sensor, showing input and output ports
Figure 3: USB wire variant with input and output ports. Unilateral line length is 25 cm.

4.3. Mode Selection (Sensing Distance)

The sensor is available in different modes, offering varying sensing distances:

  • Mode A: Sensing distance of 1-1.5 meters.
  • Mode B: Sensing distance of 3-4 meters.

Choose the appropriate mode based on your application requirements.

Diagram comparing sensing distances for Mode A (1-1.5M) and Mode B (3-4M)
Figure 4: Visual representation of Mode A and Mode B sensing ranges.

5. Operating Instructions

5.1. Light Sensing Working Procedure

The sensor operates with a light-sensing feature to conserve energy:

  1. Upon initial power-on, the light will automatically turn off after 1 second, and the sensing switch will turn off after 30 seconds.
  2. After the switch has been off for 10 seconds (equivalent to not sensing a person for 40 seconds), it enters the light sensing mode.
  3. In light sensing mode, the sensor remains on. During daylight hours, even if a person is sensed, the light will not turn on.
  4. When it gets dark, and a person is sensed, the light will turn on.

5.2. Induction Delay

After sensing a person or moving object, the light will turn off after 30 seconds. If a person remains active within the induction area, the delay will be continuously extended, keeping the light on.

5.3. Penetration Capabilities

The microwave radar sensor offers 360° induction and can penetrate certain materials, allowing for concealed installation:

  • Penetrable materials: Plank, plastic, acrylic, wood, gypsum board.
  • Forbidden materials (cannot penetrate): Glass, metal, concrete wall.
Diagram illustrating materials the sensor can and cannot penetrate
Figure 5: The sensor can detect motion through materials like wood and plastic, but not glass, metal, or concrete.

6. Troubleshooting

If the LED light remains on or off after connection, and the switch cannot be controlled, consider the following common issues and their resolutions:

6.1. Common Problems & Resolutions

  1. Mismatch of working voltage:

    Resolution: First, confirm that your power adapter is a constant voltage DC3.7V, 5V, 12V, or 24V, and that your LED light also matches the same DC3V, 3.7V, 5V, 12V, or 24V voltage. Ensure both components operate at compatible voltages.

  2. Input/output and Positive/negative poles are reversed:

    Resolution: Check your wiring carefully. If the input/output and positive/negative poles are connected in reverse, correct the connections according to the wiring diagram (Figure 2).

  3. Interference from movement within the sensing area:

    Resolution: If people, cats, dogs, mice, or even fan rotation are continuously sensed within the sensing area, the sensor may not turn off. Ensure all movable people, animals, and objects leave the sensing area for more than 8 meters and wait for 30 seconds for the sensor to reset and turn off.

7. Maintenance

  • Keep the sensor module clean and free from dust or debris that might obstruct its sensing capabilities.
  • Avoid exposing the sensor to water or excessive humidity.
  • Do not attempt to open or modify the sensor module, as this may void the warranty and cause damage.

8. User Tips

  • For best performance, install the sensor where the sensing surface has a clear line of sight to the intended detection area.
  • Consider the Mode A (1-1.5M) for smaller, confined spaces like closets or under cabinets, and Mode B (3-4M) for larger areas like hallways or rooms.
  • When testing, ensure there are no other moving objects or strong electromagnetic interference nearby that could trigger false detections.

9. Warranty and Support

This product comes with a 1-year warranty. For detailed warranty terms and conditions, please refer to the official product documentation.

For further assistance or to view the complete user manual in PDF format, please refer to the official document: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.