GGBEE HFY616

Contents

RF 433MHz Wireless Remote Control Light Switch User Manual

Model: HFY616 | Brand: GGBEE

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your GGBEE RF 433MHz Wireless Remote Control Light Switch. This system allows you to wirelessly control your lighting fixtures using a compact remote button, offering convenience and flexibility in your home lighting setup.

2. Safety Information

  • Ensure the power supply is disconnected before any installation or wiring to prevent electric shock.
  • All wiring should be performed by a qualified electrician or in accordance with local electrical codes.
  • Do not exceed the maximum load capacity of the receiver (10A, 2200W).
  • Keep the device away from water and high humidity environments.
  • Do not attempt to disassemble or repair the device yourself.

3. Package Contents

Please check the package for the following items:

  • 1 x RF 433MHz Smart Switch Receiver
  • 1 x Wireless Remote Control Button (or more, depending on the purchased variant)
  • 1 x User Manual (this document)
  • Double-sided adhesive tape for remote mounting
  • Screws and wall plugs for receiver installation
  • CR2016 batteries (pre-installed in remote or included separately)
Product overview showing the smart switch receiver and two round remote control buttons.
Figure 1: Product components including the receiver and remote buttons.

4. Setup and Installation

4.1 Wiring the Receiver

The relay controller (receiver) is designed to be installed in a standard switch bottom box. Follow the wiring diagram carefully:

  1. Connect the Live line to the 'Lin' terminal on the receiver.
  2. Connect the Neutral line to the 'Nin' terminal on the receiver.
  3. Connect the Light Live line (to the lamp) to the 'Lout' terminal on the receiver.
  4. Connect the Light Neutral line (to the lamp) to the 'Nout' terminal on the receiver.
Wiring diagram for the smart switch receiver, showing connections for live, neutral, and light lines.
Figure 2: Wiring Diagram for the Smart Switch Receiver.

Important Note: The wall switch (remote button) itself cannot directly control lights. It requires the RF receiver to function.

4.2 Pairing the Remote Control (Learning Signals)

To link your remote control button(s) with the receiver:

  1. Press the learning button on the receiver twice. Wait for 3 seconds.
  2. Press one button on the remote control. Wait for 3 seconds. The pairing is successful.
Diagram illustrating the steps to pair the remote control with the receiver.
Figure 3: Steps for Pairing the Remote Control.

4.3 Clearing Paired Signals

To clear all previously paired remote control codes from the receiver:

  • Press the learning button on the receiver 8 times.
  • Alternatively, press and hold the learning button for more than 5 seconds. The light will flash twice, indicating all remote control codes are canceled.

4.4 Remote Control Placement

The wireless remote control button can be placed anywhere using the provided double-sided tape, or simply held in hand. No wiring is required for the remote itself.

Images showing various placement options for the wireless remote control button: on glass, on a wall, or held in hand.
Figure 4: Flexible Placement Options for the Remote Control.

5. Operating Instructions

Once the receiver is wired and the remote control is paired, you can operate your lights:

  • Press the paired button on the remote control once to turn the connected light ON.
  • Press the same button again to turn the connected light OFF.
  • If power is lost and then restored, the device will default to the OFF state.
Video 1: Product demonstration showing wiring and remote control operation.

6. Maintenance

6.1 Battery Replacement

The remote control button is powered by two CR2016 3V batteries. When the remote's performance degrades or it stops responding, replace the batteries. To replace, carefully open the remote casing to access the battery compartment.

Image showing the back of the remote control button with the battery compartment visible, indicating CR2016 batteries.
Figure 5: Remote Control Battery Compartment (uses CR2016 batteries).

6.2 Cleaning

Wipe the devices with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.

7. Troubleshooting

  • Remote not responding: Check if the batteries in the remote are depleted and replace them if necessary. Re-pair the remote with the receiver following the pairing instructions.
  • Light not turning on/off: Verify that the receiver is correctly wired and receiving power. Ensure the remote is paired. Check the light bulb for functionality.
  • Poor remote range: The effective range can be reduced by obstacles. Try to minimize physical obstructions between the remote and the receiver.
  • Wall switch not working: Remember that the wall switch (remote button) is an RF transmitter only and does not directly control the lights. It must be paired with the receiver.

8. Specifications

Feature Specification
Brand Name GGBEE
Model Number HFY616
Item Type SWITCHES
Switch Type Remote Control
Material Plastic
Certification CE
Is Smart Device No
Origin Mainland China
Current 10A
EU LVD Voltage High voltage: Above 50Vac or 75Vdc
High-concerned chemical None
Transmitter (Remote) Specifications
Operating Frequency 433MHz
Power Supply 2 x 3V CR2016 Battery (Included)
Button Type 2 buttons
Size 60mm x 30mm
Operating Voltage 3V
Operating Current 12mA
Transmitting Power 10mw
Modulation Mode ASK (AM)
Encoding Type Learning Code
Transmission Distance 20~50m (open space)
Controller (Receiver) Specifications
Input Power AC85-240V 50/60HZ
Max Current 10 A
RF Frequency 433Mhz
Working Temperature -30~+80°C
RF Working Mode Superheterodyne
Receive Sensitivity >97dbm
Remote Storage 10pcs
Support Remote Type Learning code 1527code
Size 47.4 x 42 x 22.8 mm

9. Warranty and Support

This product comes with a 1-year warranty from the date of purchase. For technical support or warranty claims, please contact your retailer.

A detailed user manual in PDF format is available for download: User Manual (PDF)

10. User Tips

  • The setup process is generally straightforward and easy to follow.
  • Ensure you have CR2016 batteries on hand for the remote control, although they are typically included.
  • Consider the placement of the receiver to minimize signal interference for optimal remote range.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.