CENJITION CNC Billet Handlebar Clamp & Riser Mount Adaptor

Contents

CENJITION CNC Billet Handlebar Clamp & Riser Mount Adaptor User Manual

For 22mm/28mm Fat Bars

1. Introduction

Thank you for choosing the CENJITION CNC Billet Handlebar Clamp & Riser Mount Adaptor. This product is designed to upgrade your motorcycle's handlebar setup, allowing for adaptation to fat bars (22mm/28mm) or increasing riser height for improved riding posture. This manual provides essential information for proper installation, safe use, and maintenance.

2. Package Contents

Please check the package for the following items:

  • 1 Pair of CNC Billet Handlebar Clamps (Left and Right)
  • Mounting Screws and Hardware

Note: Instruction of Installation is NOT Included in the physical package, please refer to this manual.

Blue handlebar clamps with packaging and mounting hardware
Image: Blue handlebar clamps with packaging and mounting hardware.

3. Specifications

FeatureDescription
Condition100% Brand New
Material6061-T6 Aluminum (CNC-machined)
Surface FinishAnodized
CompatibilitySuitable for all 22mm / 28mm handlebars
Quantity1 Pair
Available ColorsBlue, Orange, Black, Red, Green, Yellow
Application ScenariosPit Dirt Bikes, Racing Motorcycles, Enduro, Supermoto, MX, ATVs, off-road/competition bikes
Black CNC Billet Handlebar Clamps
Image: Black CNC Billet Handlebar Clamps.
Red CNC Billet Handlebar Clamps
Image: Red CNC Billet Handlebar Clamps.

4. Setup and Installation

Product Name: CNC Billet Handlebar Clamp / Fat Bar Risers Mount Clamp Adaptor (for 22mm/28mm bars)

Application Instructions:

  1. Preparation: Remove the original handlebar clamps and thoroughly clean the top triple clamp surface.
  2. Placement: Place the product onto the original mounting studs or bolt holes, ensuring correct orientation.
  3. Handlebar Positioning: Position the 22mm or 28mm handlebar (refer to actual product for diameter compatibility) into the lower clamp groove. Then, place the upper clamp cover over the bar.
  4. Initial Tightening: Tighten bolts evenly in a diagonal pattern. A torque wrench is recommended (refer to actual product and original vehicle manual for torque values). Do not fully tighten one side before the other.
  5. Adjustment: Adjust the handlebar angle forward/backward to your preferred riding position.
  6. Final Tightening: Fully tighten all bolts after adjustment.
Red handlebar clamps installed on a motorcycle
Image: Red handlebar clamps installed on a motorcycle.
Original instruction sheet for CNC Billet Handlebar Clamp
Image: Original instruction sheet for CNC Billet Handlebar Clamp (text content transcribed in this manual).

5. Operating Instructions

Once installed, the handlebar clamps allow for a secure mounting of your 22mm or 28mm handlebars. The primary operation involves setting the handlebar angle to your preferred riding position during installation. No further operational steps are required beyond ensuring the clamps are securely fastened.

6. Maintenance

  • Bolt Tightness Check: Re-check bolt tightness after the first ride and after each off-road use to ensure continued security.
  • Cleaning: Clean the clamps with a soft cloth and mild cleaner as needed. Avoid abrasive materials that could damage the anodized finish.

7. Precautions and Warnings

General Precautions:

  • Keep out of reach of children.
  • Choking Hazard: Contains small parts (bolts, washers, etc.). Risk of choking. Keep away from infants and toddlers.
  • Sharp Edges: Sharp edges may exist. Wear gloves during installation to avoid cuts.
  • Torque Limits: Do not exceed the manufacturer's recommended maximum tightening torque or handlebar load limit. Over-tightening may deform or break the clamp.

Product-Specific Warnings:

  • Handlebar Diameter: Verify that your handlebar diameter (22mm or 28mm) matches this product before installation. Mismatched sizes will not clamp securely.
  • Tools: Do not use impact tools for installation. This may damage threads or the billet material.
  • Vibration Dampers: If original rubber vibration dampers are removed during installation, vibration will increase significantly, which may cause bolt loosening or metal fatigue.
  • Stacking Risers: Do not stack this product with additional risers exceeding 50mm in total height.
  • Torque Specifications: Please refer to actual product for torque specifications, thread size, and included accessories.

8. Troubleshooting

  • Clamps Not Securing Handlebar: Ensure the handlebar diameter (22mm or 28mm) precisely matches the clamp's specification. Mismatched sizes will prevent secure clamping.
  • Loose Handlebar After Installation: Re-check all bolt tightness. Ensure bolts were tightened evenly in a diagonal pattern and to the recommended torque. If rubber vibration dampers were removed, increased vibration might contribute to loosening; consider re-installing dampers if possible or using thread-locking compound (with caution).
  • Damage During Installation: Avoid using impact tools, which can strip threads or damage the aluminum. If damage occurs, do not use the product and seek replacement.

9. User Tips

  • Inspect Finish: Upon arrival, inspect the finish of the clamps. While generally good value, some users note a potentially rougher finish.
  • Easy Installation: Many users find these clamps very quick and easy to install, aligning with the provided instructions.
  • Value for Money: This product is often praised for its good value relative to its price.

10. Frequently Asked Questions (FAQ)

Q: Is this compatible with my specific motorcycle model (e.g., Honda Cargo 150)?
A: Compatibility depends on your motorcycle's handlebar diameter. This product is suitable for all motorcycles that use 22mm or 28mm handlebars. Please measure your current handlebar diameter to confirm compatibility.
Q: Are installation instructions included in the box?
A: No, detailed installation instructions are not typically included in the physical package. Please refer to Section 4 of this user manual for complete installation steps.

11. Warranty and Support

For any questions, concerns, or support regarding your CENJITION CNC Billet Handlebar Clamp & Riser Mount Adaptor, please contact your retailer or the point of purchase. Please retain your proof of purchase for any warranty claims.

© 2024 CENJITION. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.