1. Product Overview
The IKSLED 25mm Wood Panel Touch Switch is a smart touch sensor designed to control DC LED lights, offering both on/off functionality and dimming capabilities. It can be discreetly installed behind non-metallic panels up to 25mm thick, making it ideal for cabinet lighting and other hidden applications.
Image: The touch sensor module allows for discreet installation behind panels, enabling touch control from the outside.
This device supports various non-metallic materials for sensing, including wood, rock, stone, paper, acrylic, plastic, and glass.
Image: The sensor is compatible with various non-metallic materials up to 25mm thick, such as glass, rock, wood, and acrylic.
2. Safety Information
WARNING: Please strictly follow the instructions and safety tips, and use the product with caution.
- Ensure the power supply voltage matches the device specifications.
- Do not connect the device to metal materials to avoid interference.
- Verify correct polarity when connecting input and output wires.
3. Specifications
| Feature | Specification |
|---|---|
| Voltage | Constant voltage DC3.7V ~ 24V |
| Current | Max 4A (suggest 12V < 4A, 24V < 2A) |
| Sensing Distance | Suggested F47 3CM (30mm). The sensitivity varies with material thickness; thinner materials offer better sensitivity. |
| Penetrable Materials | Wood plate, rock plate, stone, paper, acrylic, plastic, glass, and other non-metallic conductor materials. |
| Material | Plastic |
| Switch Type | Touch On/Off Switch |
| Features | Touch to open, touch again to close (Mode B), dimmable (Mode B) |
4. Setup and Installation
The touch sensor is designed for easy installation behind non-metallic surfaces. Ensure the chosen installation location is free from metal materials to prevent interference.
Wiring Instructions:
The sensor module typically comes with input and output wires. Connect the input wires to your DC LED driver and the output wires to your LED lights. Pay close attention to polarity (positive and negative connections).
Image: General wiring illustration. Input connects to the LED driver, and output connects to the LED lights. Ensure correct polarity.
Image: The touch sensor module with its connection wires.
For a detailed wiring diagram and installation steps, please refer to the complete user manual available in PDF format: User manual (PDF).
5. Operating Instructions
The touch switch offers different operating modes depending on the model variant (Mode A or Mode B).
Mode A: Touch On, No Touch Off
In Mode A, a short touch will turn the LED lights on. The lights will remain on until power is removed or the circuit is otherwise interrupted. This mode does not support dimming.
Image: Mode A allows for simple touch-on functionality.
Mode B: Touch On, Touch Off, Long Touch Dimmable
In Mode B, a short touch will turn the LED lights on. Another short touch will turn the lights off. To dim the lights, perform a long touch (hold for approximately 3 seconds). The brightness will adjust gradually. Release your finger when the desired brightness is reached.
Image: Mode B provides full control with touch on/off and dimming capabilities.
6. Maintenance
The IKSLED Touch Sensor Dimmer requires minimal maintenance. Keep the installation area clean and free from excessive moisture or extreme temperatures. Avoid placing metallic objects directly on the sensing area, as this can interfere with its operation.
Regularly check wiring connections to ensure they remain secure. If the sensor is installed in a high-traffic area, periodically inspect the panel for any damage that might affect sensor performance.
7. Troubleshooting
If the LED light remains on or off, and the switch cannot be controlled, consider the following:
Common Reasons:
- Mismatch of Working Voltage: The voltage of the LED driver or LED lights does not match the sensor's specified voltage range (DC3.7V-24V).
- Input/Output and Positive/Negative Poles Reversed: The wiring connections for input/output or positive/negative poles are incorrect.
- Incorrect Usage Steps or Unfixed Switch: The induction switch was not properly fixed after power-on, or it moves during use, causing it to constantly check the environment and malfunction.
Resolutions:
- Verify Voltage Compatibility: First, confirm that your adapter provides a constant voltage (DC3.7V, 5V, 12V, or 24V) and that your LED lights are compatible with the same DC voltage.
- Check Wiring Polarity: Inspect the input/output and positive/negative pole connections. If they are reversed, please connect them correctly.
- Secure Installation: Turn off the power, securely fix the induction switch in its intended position, and then reapply power. Ensure the switch remains stable during operation.
8. User Tips
- For optimal performance, ensure the panel material is consistently within the recommended thickness (less than 25mm).
- Test the sensor's sensitivity with your chosen panel material before final installation to find the best placement.
- If experiencing intermittent issues, check for any nearby metallic objects that might be causing interference.
9. Warranty and Support
This product comes with a 1-year warranty from the date of purchase. For warranty claims or technical support, please contact your retailer or the manufacturer directly.
For additional information and detailed diagrams, please refer to the full user manual available in PDF format: User manual (PDF).