Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your new Tuya Bluetooth Fingerprint Electronic Lock. Please read this manual carefully before installation and use, and keep it in a safe place for future reference. This smart knob lock offers multiple unlocking methods including fingerprint, mechanical key, and mobile app control, integrating seamlessly into your smart home system for enhanced security and convenience.
Safety Information
- Before installing the door lock, ensure that the batteries are fully charged.
- The lock's rotating components must operate smoothly and flexibly.
- This lock requires a mechanical key for manual unlocking. Remove the mechanical key from the packaging and store it in a secure place for immediate use when needed.
- When you hear the low battery alert, charge it immediately. Avoid leaving the device in a low-power state for extended periods.
- Keep your fingers clean and dry when using the fingerprint sensor.
Packing List
Please unpack the product package and check whether the following accessories are included:
- Front Lock Handle (x1)
- Rear Lock Handle (x1)
- Lock Body (x1)
- Strike Plate (x1)
- Gusset Box (x1)
- Keys (x2)
- Installation Key (x1)
- 45mm M4 Screw (x3)
- M4x21 Screw (x4)
Installation Guide
Door Lock Installation Diagram
Before installation, please measure your door thickness. The lock is compatible with door thicknesses between 35mm and 55mm. Ensure the center-to-center distance conforms to the 60/70mm standard. The hole diameter should be 55mm.
For a visual guide, please refer to the '03.Door Lock Installation Diagram' section in the full PDF manual available at Item guides & documents (PDF).
Attachment Steps
Follow these steps for attaching the lock components. For detailed diagrams, please consult the full PDF manual.
- Install the lock body properly into the door.
- Firmly tighten the lock body screws.
- Align the lock body with the holes for proper installation.
- Use the provided key to depress the spring and detach the rear lock handle.
- Mount the rear lock handle by utilizing the lever hole.
- Install and tighten the remaining screws.
- Align the gap and install the front handle.
Operation
Mechanical Knob Operation
- To Open: Rotate the knob in the door vertically. If the lock is in the normally open state, continuously verify the fingerprint twice within 3 seconds. If the lock is closed, verify the fingerprint once.
- To Lock: Rotate the knob in the door to the horizontal position to reverse and lock it.
- Anti-Lock Mode: When the lock is in anti-lock mode, only the administrator's fingerprint can be matched. The lock will automatically anti-lock 5 seconds after unlocking.
App Connection (Tuya App Unlocked)
To connect your smart lock to the Tuya app:
- Download the Tuya Smart App from your mobile application market. You can search for "TuyaSmart" or scan the QR code provided in the full PDF manual.
- Open your phone's Bluetooth and Location services.
- Open the Tuya Smart App.
- In the app, click "Add Device" and begin the connection process.
- Select your device (e.g., "New smart knob lock") manually to start connecting.
- Once the connection is successful, you can enter the homepage to add users, manage members, or change names.
- To remove the device, navigate to its settings in the app and select "Remove Device". Confirm unbinding and clearing data when prompted.
Fingerprint Enrollment
To enroll fingerprints for your smart lock:
- In the Tuya app, navigate to the lock's settings and click the "Add" button next to "Fingerprint".
- Confirm the addition process in the app.
- Repeatedly place and remove your finger on the fingerprint sensor five distinct times as instructed by the app. Ensure your finger and the sensor are clean and dry for accurate enrollment.
Restore Factory Settings
You can restore the lock to factory settings using two methods:
- Via Tuya App: Data can be emptied through the Tuya app by removing the device and confirming to wipe data.
- Local Operation: After repeatedly rotating the knob 5 times within 5 seconds, the lock will enter the factory reset state. The blue light of the fingerprint head will stay on. Touch any fingerprint within 10 seconds to clear all data. The buzzer will beep for a long time, and will sound when the button is pressed and raised during this process.
Lights and Buzzers
- Successful Identification: Green light turns on, one buzzer sound.
- Failed Identification: Red light flashes three times, two buzzer sounds.
- Charging: Red light is on.
- Fully Charged: Green light is on.
- Low Power Alarm: Red light flashes five times after opening the door.
Low Power Consumption State
- Not Bound to Bluetooth: If the system is not bound to a Bluetooth device, it enters a sleep state after 15 seconds of no fingerprint touch or knob twist. To wake it up and search for a connected Bluetooth device, touch the fingerprint sensor or press a button.
- Bound to Bluetooth: If bound to a Bluetooth device, the lock enters a sleep state after 4 seconds of no fingerprint touch or knob twist. It does not need to be woken up, and the mobile phone can directly initiate a Bluetooth connection through the Tuya Smart APP.
Troubleshooting
Trial and Error Locking
If there are 5 consecutive recognition errors, the device will enter a 120-second lock state. During this time, the fingerprint sensor will not respond, and an alarm sound will be emitted for 10 seconds. The lock can only be unlocked by Bluetooth or by waiting for the 120-second lockout period to expire.
Low Battery
If you hear a low battery alert (red light flashes five times after opening the door), charge the lock immediately using a Type-C cable. Avoid prolonged use in a low-power state.
Connection Issues
If the app cannot find the device, ensure your phone's Bluetooth and Location services are enabled. If the device is not bound to Bluetooth, touch the fingerprint sensor or press a button to wake it up from sleep mode.
Specifications
| Feature | Specification |
|---|---|
| Admin ID Range | 3 |
| User ID Range | 17 |
| Fingerprint Capacity | Up to 20 sets |
| Power Supply | Built-in Rechargeable Battery (Type-C, 5V 1A) |
| Standby Power Consumption | ≤ 20 µA |
| Operating Power Consumption | < 200 µA |
| Low Voltage Alert | 4.5V ± 0.2V (indicator flashes three times below 4.3V) |
| Operating Temperature | -20°C to 70°C |
| Operating Humidity | 20% to 90% RH |
| Compatible Door Thickness | 35-55mm |
| Ways To Unlock | App, Mechanical Keys, Fingerprint |
| Smart Home Platform | Tuya |
| Certification | CE |
User Tips
- Fingerprint Management: The lock supports up to 20 unique fingerprints. Ensure you enroll all necessary users for convenient access.
- Battery Life: The built-in rechargeable battery provides approximately 12 months of working time. Always charge promptly when the low battery alert is triggered to avoid being locked out.
- Mechanical Key Backup: Keep the mechanical keys in a safe, accessible location outside the locked area as a backup in case of battery depletion or electronic malfunction.
- App Control: Utilize the Tuya Smart App for remote management, adding/removing users, and monitoring lock status. Ensure Bluetooth and location services are active on your phone for seamless app connectivity.
Warranty and Support
For warranty information, technical support, or further assistance, please refer to the official product documentation or contact the seller directly. Always keep your purchase receipt for warranty claims.
A complete version of this user manual, including detailed diagrams and troubleshooting, is available in PDF format: Tuya Smart Knob Lock User Manual (PDF).