ANDELI OPTIM-600LB-TGP

Contents

ANDELI Auto Darkening Welding Helmet User Manual

Model: OPTIM-600LB-TGP (also referred to as RL-600LB)

Introduction

Thank you for choosing the ANDELI Auto Darkening Welding Helmet. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your welding helmet. Please read this manual thoroughly before using the product and keep it for future reference.

This helmet features advanced auto-darkening technology, integrated LED lighting, gesture control, and a comfortable design for various welding applications.

1. Safety Information

WARNING: Welding can be hazardous. Protect yourself and others from possible serious injury or death. Keep children away. Pacemaker wearers should consult with their doctor before operating.

1.1 General Safety Precautions

  • Always examine the carton and equipment for damage immediately upon receipt. Claims for damaged shipments must be made to the transportation company.
  • Do not install, operate, or repair this equipment without reading the entire manual and understanding all safety precautions.
  • Always wear safety glasses or goggles under the welding helmet.
  • Ensure the clear lens is clean and securely attached.
  • Protect your body from welding spatter and arc flash with appropriate protective clothing (woolen clothing, flame-proof apron, gloves, leather leggings, high boots).
  • Protect others from splatter, flash, and glare with protective screens or barriers.
  • Ensure all protective equipment is in good condition.

1.2 Arc Rays Can Burn

  • The electrode and work circuits are electrically "hot" when the welder is on. Do not touch these parts with bare skin or wet clothing. Wear dry, hole-free gloves.
  • Insulate yourself from work and ground using dry insulation.
  • Always ensure the work cable makes a good electrical connection with the metal being welded, as close as possible to the welding area.
  • Maintain the electrode holder, work clamp, welding cable, and welding machine in good, safe operating condition. Replace damaged insulation.
  • Never simultaneously touch electrically "hot" parts of electrode holders connected to two welders.
  • When working above floor level, use a safety belt to protect from falls due to electric shock.

1.3 Fumes and Gases Can Be Dangerous

  • Welding produces fumes and gases hazardous to health. Avoid breathing these fumes.
  • Keep your head out of the fume plume.
  • Use sufficient ventilation or exhaust at the arc to keep fumes and gases away from your breathing zone and the general area.
  • Do not weld in locations near chlorinated hydrocarbon vapors (e.g., from degreasing or spraying operations), as heat and arc rays can react with solvent vapors to form highly toxic gases.
  • Shielding gases can displace air and cause injury or death. Ensure adequate ventilation, especially in confined areas.

1.4 Welding and Cutting Sparks Can Cause Fire or Explosion

  • Remove all fire hazards from the welding area. If not possible, cover them to prevent sparks from starting a fire.
  • Welding sparks and hot materials can easily pass through small cracks to adjacent areas.
  • Avoid welding near hydraulic lines. Have a fire extinguisher readily available.
  • Do not heat, cut, or weld tanks, drums, or containers that have held flammable or toxic substances unless properly cleaned and prepared. They can explode.
  • Vent hollow castings or containers before heating, cutting, or welding.
  • Wear oil-free protective garments (leather gloves, heavy shirt, cuffless trousers, high shoes, cap). Wear ear plugs when welding out of position or in confined places.

1.5 Electric and Magnetic Fields (EMF)

  • Electric current creates EMF fields around welding cables and machines.
  • EMF fields may interfere with some pacemakers. Welders with pacemakers should consult their physician.
  • To minimize EMF exposure: route electrode and work cables together (tape if possible), never coil electrode lead around your body, do not place your body between electrode and work cables, connect work cable to workpiece as close as possible to the welding area, and do not work next to the welding power source.

1.6 Special Situations

  • Do not weld or cut containers or materials that previously held hazardous substances unless properly cleaned.
  • Do not weld or cut painted or plated parts unless special ventilation precautions are taken, as they can release highly toxic fumes.
  • Protect compressed gas cylinders from excessive heat, mechanical shocks, and arcs; fasten them securely.
  • Ensure cylinders are never grounded or part of an electrical circuit.
  • Remove all potential fire hazards from the welding area.
  • Always have fire fighting equipment ready and know how to use it.

2. Specifications

The ANDELI Auto Darkening Welding Helmet (Model OPTIM-600LB-TGP / RL-600LB) offers the following technical specifications:

FeatureRL-600LBRL-600LA (for comparison)
Optical Class1/1/1/21/1/1/1
LCD Viewing Area115 x 82 mm (4.53" x 3.23")115 x 82 mm (4.53" x 3.23")
Cartridge Size131 x 135 mm (5.31" x 5.15" x 0.39")131 x 135 mm (5.31" x 5.15" x 0.39")
UV/IR ProtectionDIN 16DIN 16
Arc Sensors45
Variable Welding ShadesWELD: DIN 9-13, CUT: DIN 5-9, GRIND: DIN 3, LOCK: DIN 5-13WELD: DIN 9-13, CUT: DIN 5-9, GRIND: DIN 3, LOCK: DIN 5-13
Shade ControlDigital AdjustDigital Adjust
Sensitivity ControlDigital AdjustDigital Adjust
Power SupplySolar Cells + Polymer BatterySolar Cells + Polymer Battery
Battery Capacity500mAh500mAh
Charging TypeType-CType-C
Low Battery IndicatorYesYes
Light to Dark Switching Time0.08 ms (1/30000s)0.07 ms
Dark to Light Switching Time0.1 - 1.0 s0.1 - 2.0 s
TIG RatingDC 5A / AC 5ADC 5A / AC 5A
Operating Temperature-5°C to 55°C (23°F to 131°F)-5°C to 55°C (23°F to 131°F)
Storage Temperature-20°C to 70°C (-4°F to 158°F)-20°C to 70°C (-4°F to 158°F)
Total Weight560 g (1.2 LB)590 g
Helmet MaterialPPPP

Included Accessories: 2 External Protective Lenses, 1 Internal Protective Lens, 1 Type-C Charging Cable (50cm), 1 Convenient Bag.

ANDELI Welding Helmet with included accessories

Image: The ANDELI Auto Darkening Welding Helmet shown with its standard accessories: two external protective lenses, one internal protective lens, a Type-C charging cable, and a convenient carrying bag.

3. Setup and Initial Adjustments

3.1 Headgear Adjustment for Comfort

The helmet's headgear is designed for all-day comfort with 6 separate contact points to distribute weight and eliminate pressure. Proper adjustment is crucial for safety and comfort.

Diagram of ANDELI welding helmet headgear adjustments

Image: Detailed diagram of the welding helmet's headgear, highlighting seven adjustable components for comfort: 1. Cushioned Front, 2. Front/Back Adjustment, 3. Adjustable Top Strap, 4. Cushioned Side, 5. Cushioned Back, 6. Widen Rear Headbands, and 7. Tightness Adjustment Knob.

  1. Head Size Adjustment: Turn the Ratchet Knob (located at the back of the helmet) right or left to adjust the headgear tightness for your desired head size.
  2. Crown Adjustment: Adjust the comfort strap and snap the pins into the holes to lock securely in place.
  3. Tilt Adjustment: Located on the right side of the helmet. Loosen the right headgear tension knob, push the top end of the adjustment lever outward until it clears the notches. Rotate the lever forward or back to the desired tilt position. The stop will automatically engage when released.
  4. Fore/Aft Adjustment: Adjusts the distance between your face and the lens. Slide and hold the spring-loaded caps upward while moving the headgear into one of four slotted locations. Release the cap once the desired distance is achieved. Ensure both sides are equally positioned.

3.2 Initial Checks

  • Before welding, always inspect the helmet and filter lens to ensure they are properly fitted, in good condition, and not damaged.
  • Check that the clear lens is clean and securely attached to the helmet.
  • Ensure the battery is sufficiently charged (refer to Section 5 for charging instructions).
  • Perform a self-check of the auto-darkening function (refer to Section 4.2).

4. Operating Instructions

4.1 Helmet Controls (RL-600LB Model)

ANDELI welding helmet control panel and features

Image: A composite image showcasing various features of the ANDELI welding helmet: 180° Panoramic View, Type-C Charging, 6 Contact Points Headgear, 4 Arc Sensors, 1/30000s Higher Sensitivity, Lightweight (560g/1.2LB), and a Fully Digital True Color lens with 1/1/1/2 optical class. The main control panel is visible with "MODEL:RL-600LB", "GRIND", "CUT", "WELD", "SENS", "DELAY", "TEST", and adjustment buttons.

ANDELI welding helmet lens and remote control details

Image: Focus on the welding lens (4.53"x3.23" view area) and its digital controls. The main control panel shows "MODE" (grind, cut, weld), "TEST", "SENSI" (sensitivity adjustment), and "DELAY" (dark-to-light speed). It also illustrates how to decrease/increase shade levels (13-9 and 9-13 respectively). A separate remote control is shown with buttons for Quick Sensitivity & Delay Switch, Shade Control, and Quick Grind Mode Switch (Power on/off).

The helmet features a fully digital control panel and an external quick-access button for convenient adjustments.

Main Control Panel (Inside the Helmet)

  1. Mode Button: Press to select the appropriate mode for your work activity:
    • Weld Mode: For most welding applications. Lens darkens upon sensing an arc. Adjust shade, sensitivity, and delay.
    • Cut Mode: For cutting applications. Lens darkens upon sensing a cutting arc. Adjust shade, sensitivity, and delay.
    • Grind Mode: For metal grinding. Shade is fixed at No. 3. No lens adjustments possible.
    • Lock Mode: Temporarily locks current darkening settings during welding for repetitive tasks.
  2. Test Button: Press to test if the auto-darkening function is working correctly before welding.
  3. Sensitivity Button: Adjusts the detection threshold of the arc sensors. Controls how easily sensors trigger lens darkening. 5 levels of adjustment.
    • Recommended Settings: Low-Current TIG Welding (High Sensitivity), High-Current MIG/Stick Welding (Medium to Low Sensitivity), Outdoor Welding (Lower Sensitivity), Factory/Group Welding (Lower Sensitivity).
  4. Delay Button: Controls the time delay between the end of the welding arc and the lens returning to its light state. Protects eyes from afterglow and cooling slag.
  5. '+' and '-' Buttons: Adjust lens shade in darkened state. Weld: No.9-No.13, Cut: No.5-No.9, Grind: No.3.

External Button Control

  • Quick-Access Button: Instantly switches between Sensitivity and Delay adjustment modes.
  • Multi-Function Knob: Quickly adjusts Shade Number, Sensitivity, and Delay values.
  • Grind Mode Button: Long press for 1.5 seconds to activate grind mode immediately (Power on/off).

4.2 Integrated LED Lighting

ANDELI welding helmet with LED lights illuminating workspace

Image: A welder wearing the ANDELI helmet with its integrated LED sidelights illuminating the workspace. Text indicates "ILLUMINATE YOUR WHOLE WORKSPACE" with "2 Premium LED Sidelights", "Up to 350 Lumens", and "2 Levels Adjustable Brightness" (Low/Strong).

The helmet is equipped with 2 premium LED sidelights providing up to 350 lumens for illuminating your entire workspace.

  1. ON/OFF: Long press and hold the ON/OFF button for three seconds to turn on the light. Press again to switch between two adjustable brightness levels.
  2. Left LED Indicator: A green light indicates the spotlight is in operation.
  3. Infrared Sensor Switch: When the spotlight is on, press this switch to activate infrared sensing mode (indicated by a flashing left indicator light).
  4. Infrared Sensor Probe: Hand motion can control the light switch in infrared sensing mode.

4.3 Intelligent Brightness Gesture Control

ANDELI welding helmet with gesture control feature

Image: The ANDELI welding helmet demonstrating its "INTELLIGENT BRIGHTNESS GESTURE CONTROL" for hands-free operation. It shows "AUTO ON" (deactivates on proximity) and "AUTO OFF" (reactivates when reapproached) features.

The helmet features intelligent brightness gesture control for completely hands-free operation:

  • Auto ON: The light deactivates when you are in close proximity to the workpiece.
  • Auto OFF: The light reactivates when you move away from the workpiece.

5. Maintenance

5.1 Battery Charging and Life

The device is equipped with a 500mAh polymer battery and supports charging via the Type-C port (rated input: DC 5V/1A). A 50cm Type-C cable is included.

  • Standard Battery Life: Approximately 2 hours of continuous operation (single battery).
  • Long Battery Life: Approximately 4 hours of continuous operation (dual batteries).
  • Charging: Recharge promptly using the provided Type-C cable when the battery level is low. The battery level is displayed in the top-right corner of the screen.

5.2 Cartridge and Lens Replacement

WARNING: Never use the auto-darkening lens without the inside and outside lens covers properly installed. Welding spatter will damage the auto-darkening lens and void the warranty.

Replacing the Outer Cover Lens

  1. Removal: Press down on one side of the buckle with your hand to release and remove the shell.
  2. Installation: To install a new shell, first align and clip it into the middle groove. Then, press firmly on both sides until it locks into place.

Replacing the Inner Cover Lens

  1. Remove the lens cover holder and take out the lens assembly.
  2. To remove the inner lens cover, gently pry it upward using the thumbnail openings located on both sides.
  3. Slide the cover out from either side of the frame.
  4. Insert the new lens cover and reassemble the unit by reversing the above steps.

5.3 Cleaning

  • Clean the outer lens with a soft cloth. Replace if damaged or scratched.
  • Gently clean sensor surfaces with a soft, dry cloth.
  • Do not use abrasive cleaners or solvents on any part of the helmet.

6. Troubleshooting

WARNING: If these troubleshooting steps do not resolve the issue, discontinue use immediately and contact ANDELI support for assistance. Do not use a malfunctioning auto-darkening helmet.

Fault DescriptionPossible CauseSolution
Irregular darkening or uneven dimmingImproperly adjusted headband causing uneven distance between eyes and filter lens.Readjust the headband to ensure equal distance to the filter on both sides.
Filter does not darken or flickers during use
  • Dirty or damaged outer protective lens.
  • Blocked or dirty arc sensors.
  • Welding current below activation threshold.
  • Low battery or poor contact.
  • Device not switched to appropriate operating mode.
  • Clean outer lens with a soft cloth; replace if damaged.
  • Gently clean sensor surfaces.
  • Increase sensitivity setting or welding current.
  • Check battery level, condition, and contacts; recharge or clean as needed.
  • Ensure device is powered on and set to correct welding mode via control panel.
Slow response when darkeningOperation in low-temperature conditions.Do not use below -10°C; allow helmet to warm to operating temperature.
Poor visibility through lens
  • Dirty outer/inner cover lenses or filter.
  • Insufficient ambient light in work area.
  • Incorrect shade number setting.
  • Replace soiled or scratched lenses.
  • Ensure adequate workspace lighting.
  • Adjust shade number to suitable level for the process.
Helmet slips during useLoose or improperly fitted headband.Adjust headband size and tension for secure and comfortable fit.

7. User Tips

  • Always keep spare outer and inner protective lenses on hand, as they are consumable parts that can get scratched or spattered.
  • Regularly check the battery indicator, especially before starting a long welding session, to avoid interruptions.
  • Experiment with the sensitivity and delay settings in a safe environment to find what works best for your specific welding process and lighting conditions.
  • Utilize the integrated LED lights for better visibility in dimly lit areas, which can improve weld quality and safety.
  • Ensure the headgear is adjusted snugly but comfortably to prevent the helmet from slipping during work, which can be a safety hazard.

8. Warranty and Support

For warranty information, technical support, or replacement parts, please contact ANDELI customer service. Keep your purchase receipt as proof of purchase.

After-Sales Center Contact Information:

USA: LIPOINCD-100, 12 Hughes Irvine, CA 92618
Telephone: +19496179002

Hong Kong: Workshop60, 3/F, Block A, East Sun, Industrial Centre, No.16 Shing Yip Street, Kwun Tong, Hong Kong
Telephone: +85284807265

Email: support@andeligroup.com
Website: www.andelitools.com

When contacting support, please have your product model (OPTIM-600LB-TGP or RL-600LB) and a description of the issue ready.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.