1. Introduction
Thank you for purchasing this HDMI wireless extender. This device provides an easy way to extend an HDMI signal wirelessly in open environments up to 50 meters (164 feet). For optimal performance and safety, please read this manual carefully and retain it for future reference.
Product Characteristics
- Consists of a transmitter unit (TX) and a receiver unit (RX).
- The transmitter supports loop output for convenient monitoring.
- Supports multiple resolutions, including 480i/576i up to 1080P@50/60Hz.
- Utilizes 5G single frequency for fast transmission speed and strong anti-interference capabilities.
- External antenna design supports long-distance transmission up to 50 meters in an open-air environment (note: ambient interference may affect performance).
- Plug and play functionality, requiring no driver installation on the computer.
2. Safety Information
Please read the following safety guidelines and installation instructions carefully:
- Observe all warnings and prompts on this device.
- Do not expose the equipment to rain, moisture, or liquids.
- Do not insert any objects into the device.
- Do not attempt to repair the equipment or open its casing without professional assistance.
- Follow guidelines to prevent electronic shock.
- Ensure adequate ventilation openings to prevent overheating and potential damage to the product.
- Always power off the device before installation to ensure environmental safety.
Usage Limitation
This device is designed for DC5V power input only. If using a third-party power adapter, ensure its specifications match the required DC5V input.
Transmission Distance
- Outdoor barrier-free space: Up to 50 meters (164 feet).
- One-to-multi mode: Performance may vary depending on actual testing conditions.
3. Specifications
| Parameter | Description |
|---|---|
| HDMI Version and HDCP | HDMI V1.3, HDCP V1.2, HDMI V1.4 |
| Compressed format | H.264 |
| Maximum pixelclock | 165MHz |
| Maximum data rate | 6.75Gbps |
| Resolution | Max 1920x1080p@60Hz |
| Connector | HDMI-A |
| Impedance | 100 Ω |
| Recommend HDMI maximum input/outputrange | Less than 5 meters, when 1920x1080p@60Hz |
| Radio power | 13dbm |
| Wireless standards | 802.11ac supports 20MHz |
| Signal direction | Unidirectional |
| Radio frequency | 5.8G |
| Transmission distance | 50 meters |
| Power | Adapter: DC 5V=1A |
| Power consumption | Transmitter Max 5W, Receiver Max 5W |
| Operation temperature | -5°C ~ +70°C |
| Operation Humidity | 5%~90% |
| Product Size | 103*38*17mm |
4. Interface Description
The following diagram illustrates the various interfaces and indicators on the HDMI Wireless Extender units:

Image: Interface specification diagram for the HDMI Wireless Extender.
- HDMI Input (Transmitter): Connects to the signal input source (e.g., laptop, DVD player).
- HDMI Output (Receiver): Connects to a display device (e.g., TV, projector, monitor).
- Power Indicator: LED light indicating power status.
- Signal Indicator: LED light indicating signal status.
- Power Input DC/5V: Connects to a DC 5V power adapter or USB charger for power.
- Antenna Connector: For attaching the external antenna.
- Pair Key: Used for pairing the transmitter and receiver units.
5. Setup Instructions
Transmitter Connection
- Connect the HDMI cable from your high-definition player (such as a DVD player, set-top box, laptop, camera, or desktop computer) to the HDMI Input port on the transmitter unit.
Receiver Connection
- Connect an HDMI cable from the HDMI OUT port on the receiver unit to your display device (such as an HDTV, projector, monitor, or LED large screen).
Power Connection
Connect one end of the attached USB power cable to a USB power supply device (e.g., USB wall adapter, computer USB port) and the other end to the DC/5V input port of both the transmitter and receiver units.
Initial Power-On and Status
When the device is powered on, the "Power" LED will light up. The display screen will initially show "Loading...". If the transmitter and receiver have been previously paired, they should connect automatically. If the display shows "Search TX for 30 seconds", you will need to pair the transmitter and receiver again (refer to the 'Pairing Steps' section).
Connection Diagrams
The following diagrams illustrate various connection scenarios:

Image: One Transmitter to One Receiver Connection.

Image: One Transmitter to Multiple Receivers Connection.

Image: Multiple Transmitters to One Receiver Connection.
6. Operating Instructions: Pairing Steps
The HDMI Wireless Extender requires pairing between the transmitter and receiver units to establish a connection. Follow the instructions below for different pairing scenarios.
One-to-One Pairing Method (One Transmitter and One Receiver)
- First, press and hold the 'Pair' key on the transmitter. While holding, power on the transmitter. Wait for the green light to flash, then release the key.
- Next, press and hold the 'Pair' key on the receiver. While holding, power on the receiver. Wait for the green light to flash, then release the key.
- Connect the transmitter and receiver using an HDMI female-to-female cable (if needed for direct pairing). Wait until the green light of the receiver is continuously on. At this point, the transmitter's green light should still be flashing, indicating that pairing is complete. If the receiver's light is still flashing, pairing was unsuccessful; power off both units and try again.
- After successful pairing, power off both the transmitter and receiver. Unplug any HDMI female-to-female cable used for pairing and wait a few seconds before powering them on again. The green lights on both units should flash, indicating successful pairing and operation.
One-to-Many Pairing Method (One Transmitter and Multiple Receivers)
This method allows one transmitter to send a signal to up to four receivers simultaneously.
- First, pair the transmitter with the first receiver using the 'One-to-One Pairing Method' described above.
- Then, pair the same transmitter with the second receiver using the same one-to-one method.
- Repeat this process for the third and fourth receivers. Once all desired receivers are successfully paired with the same transmitter one-to-one, they can be powered on for use.
Multi-to-One Pairing Method (Multiple Transmitters and One Receiver)
This method allows one receiver to display signals from up to six different transmitters, switching between them as needed.
- First, press and hold the 'Pair' key on the receiver. While holding, power on the receiver. Wait for the green light to flash, then release the key.
- Next, press and hold the 'Pair' key on the transmitter. While holding, power on the transmitter. Wait for the green light to flash, then release the key.
- Connect the receiver and transmitter using an HDMI female-to-female cable (if needed for direct pairing). Wait until the green light of the transmitter is continuously on. At this point, the receiver's green light should still be flashing, indicating that pairing is complete. If the transmitter's light is still flashing, pairing was unsuccessful; power off both units and try again.
- After successful pairing, power off both the receiver and transmitter. Unplug any HDMI female-to-female cable used for pairing and wait a few seconds before powering them on again. The green lights on both units should flash, indicating successful pairing and operation.
- According to the one-to-one pairing method, pair the first transmitter with a receiver. After the pairing is successful, pair the second transmitter with this receiver one-to-one. By analogy, pair the third, fourth, fifth, and sixth transmitters with the same receiver one-to-one. When each transmitter and the same receiver are paired one-to-one successfully, the pairing is completed, and the power can be turned on.
Switching Method (Multi-to-One)
When using multiple transmitters with one receiver, you can switch between the input sources:
- To display the signal from Transmitter 1, press the 'Pair' key on Transmitter 1.
- To display the signal from Transmitter 2, press the 'Pair' key on Transmitter 2.
- Follow the same procedure for any other connected transmitters.
Video: Demonstration of the HDMI Wireless Extender setup and usage, showing a laptop screen mirrored to a larger display.
7. Maintenance
To ensure the longevity and optimal performance of your HDMI Wireless Extender, please follow these maintenance guidelines:
- Keep the devices clean and dry. Avoid exposure to dust, dirt, and extreme temperatures.
- Do not use harsh chemicals or abrasive cleaners. Wipe with a soft, dry cloth if needed.
- Store the devices in a cool, dry place when not in use.
- Handle the antennas and connectors with care to prevent damage.
8. Troubleshooting (FAQ)
- Q: The device does not display anything.
- A: Re-pair the transmitter and receiver (refer to the 'Pairing Steps' section).
- Q: The power LED is off.
- A: 1. Ensure the power adapter is connected correctly. 2. Ensure the power supply is not interrupted.
- Q: The display screen shows "searching and sending" for a long time.
- A: 1. Check if the transmitter is turned on. 2. Check if the transmitter is connected correctly.
- Q: No video or poor video quality.
- A: 1. Check if the connectors and wires are damaged and ensure they are correctly connected to the corresponding interface. 2. Ensure there is video output from the source device. 3. Check if the receiver is correctly connected to the display device. 4. Ensure that all equipment is within the supported transmission distance. Try bringing them closer and testing again.
9. Packing List
- HDMI wireless extender transmitter: 1
- HDMI wireless extender receiver: 1
- External antenna: 2
- Micro USB charging cable: 2
- HDMI male to female adapter cable: 2
- User manual: 1
10. User Tips
While no specific user tips were provided from reviews or Q&A, here are some general recommendations for optimal performance:
- For best signal quality, ensure a clear line of sight between the transmitter and receiver. Obstacles like walls or furniture can reduce the effective transmission distance.
- Avoid placing the units near other wireless devices (e.g., Wi-Fi routers, cordless phones) that operate on the 5GHz frequency band, as this can cause interference.
- Always use the provided power cables and ensure both units receive stable 5V power. Insufficient power can lead to unstable connections or poor video quality.
- If experiencing intermittent signal, try repositioning the antennas or moving the units closer together.
11. Warranty and Support
For warranty information and technical support regarding your Qkens HDMI Wireless Extender, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.