1. Introduction
Thank you for purchasing the TOPPING B200 Pure Post-amp Single Channel Power Amplifier. This manual provides detailed instructions for the safe and proper use of your device. Please read it thoroughly before operation and keep it for future reference.
2. Package Contents
Please check the package for the following items:
- B200 Unit x 1
- AC to DC Power Adapter x 1
- AC Cable x 1
- Product Information Card x 1
- 12V Trigger Cable x 1

3. Product Overview
3.1 Front Panel

- Power & Input Switch: Press briefly to turn on or select the input. Press and hold to turn off.
- Input Indicators (IN1, IN2, IN3): LEDs that show the currently selected input.
3.2 Rear Panel

- Mono Balanced Combo Input (IN1-3): Accepts XLR or 6.35mm TRS connectors.
- + Speaker Output (4mm Jack): Positive terminal for speaker connection.
- - Speaker Output (4mm Jack): Negative terminal for speaker connection.
- Power Input (DC 64V): Connect the provided power adapter here.
- Firmware Upgrade Interface (Type-C): For firmware updates only.
- Gain Setting Switch (H/L): Selects between High (H) and Low (L) gain.
- 12V Trigger In (3.5mm Jack): Allows synchronized power control with other compatible devices.
4. Setup
4.1 Connecting the Input Source
Use high-quality TRS or XLR balanced cables to connect your preamplifier or DAC to the B200's input jacks (IN1, IN2, or IN3).
4.2 Connecting the 12V Trigger
If you have a device with a 12V Trigger output, connect it to the B200's 12V Trigger In port using the supplied 3.5mm cable. This allows the B200 to power on/off in sync with the connected device.
4.3 Connecting Passive Speakers
The B200 provides 4mm jack speaker terminals. Ensure your speakers are rated for the amplifier's output power and impedance (≥4Ω).
Connection Methods:
- Direct Insertion (Banana Plug):
- Tighten the crystal case clockwise.
- Insert the banana plug into the end of the corresponding terminal.
- Bare Wire / Y-Insertion:
- Unscrew the crystal case counterclockwise.
- Insert stripped metal speaker wires into the round holes in the copper posts, or insert Y-terminals around the periphery of the posts.
- Finally, tighten the crystal case.
Caution: Do not let bare speaker wires touch each other or the metal casing of the B200 unit. This can cause damage to the amplifier and speakers.
4.4 Power Connection
Connect the provided AC to DC power adapter to the B200's DC 64V power input. Then, plug the AC cable into the power adapter and a suitable wall outlet.
4.5 Stereo System Configuration
For a stereo setup, two B200 units are required. Each B200 unit will drive one passive speaker (one for the left channel, one for the right channel).

5. Operating Instructions
5.1 Power On/Off
Briefly press the Power & Input switch on the front panel to turn the unit on. Press and hold the switch to turn the unit off.
5.2 Input Selection
When the unit is on, briefly press the Power & Input switch to cycle through the available inputs (IN1, IN2, IN3). The corresponding LED indicator on the front panel will light up.
5.3 Gain Setting
Use the Gain Setting switch on the rear panel to select between High (H) and Low (L) gain. Choose the appropriate gain setting based on your source device's output level and speaker sensitivity.
- Low Gain (L): 11.6dB
- High Gain (H): 22.0dB

6. Maintenance
- Keep the unit in a dry, cool environment, away from direct sunlight, high temperatures, and humidity.
- Do not expose the unit to strong impacts or vibrations.
- Clean the unit with a soft, dry cloth. Do not use liquid or abrasive cleaners.
- Ensure proper ventilation around the unit to prevent overheating.
7. Troubleshooting
If you encounter any issues with your TOPPING B200, please refer to the official TOPPING Audio FAQ for solutions:
https://www.toppingaudio.com/faq
If the problem persists, please contact TOPPING customer service:
Email: service@tpdz.net
8. Specifications
| Parameter | Value (BAL Input) |
|---|---|
| THD+N @1kHz (A-wt) | <0.00008% @4Ω 5W, <0.000075% @8Ω 5W |
| THD @20-20kHz (90kBW) | <0.0005% @4Ω 5W, <0.0004% @8Ω 5W |
| SNR (A-wt) | 145dB |
| Dynamic Range @1kHz (A-wt) | 145dB |
| Frequency Response | 20Hz-40kHz (±0.2dB), 20Hz-100kHz (±0.4dB) |
| Output Level | 80Vpp @4Ω, 110Vpp @8Ω |
| AP Measured Noise Level (A-wt) | <2.3uVrms @G=L, <3.9uVrms @G=H |
| Input Sensitivity | 12.5Vrms @G=L, 3.9Vrms @G=H |
| Gain | 11.6dB @G=L, 22.0dB @G=H |
| Output Impedance | <5mΩ |
| Input Impedance | 10KΩ |
| Output Power | 200W @4Ω THD+N<1%, 240W @8Ω THD+N<10%, 200W @8Ω THD+N<1% |
| Adapter Impedance | ≥4Ω |
Note: The above data is the result of testing under the condition of AC220V 50Hz in TOPPING's laboratory.

9. User Tips
No specific user tips were available from the provided data (reviews or Q&A).
10. Warranty and Support
- Opening the case of the B200 unit will instantly void the warranty.
- For any repairs or service, please contact TOPPING customer service at service@tpdz.net.
- TOPPING accepts no liability for any loss or damage arising directly or indirectly from the failure of the B200.
- Product specifications and features are subject to change without prior notice for improvement purposes.