ZMINR LIGHT D1S D3S D2S D4S D8S LED Headlight Bulb

Contents

ZMINR LIGHT D-Series LED Headlight Bulb User Manual

Model: D1S D3S D2S D4S D8S LED Headlight Bulb

Brand: ZMINR LIGHT

Introduction

Dear user, to ensure proper use of this product, please read this manual before use. This product is only suitable for use in motor vehicle headlights for upgrading original D-Series Xenon headlight models. It is not suitable for halogen headlight models.

Product Features

  • Lossless Upgrade: Achieves 100% decoding without altering original wiring, damaging AFS, or auxiliary functions.
  • Advanced Cooling System: Features a Shark Fin + Fan Cooling System, LED Smart Chip, and Vacuum Heat Transfer Copper Pipe for efficient heat dissipation.
  • Superior Brightness: Increases brightness by 500% compared to original car headlights, reaching up to 10,800LM.
  • Instant Illumination: Lights up in 0.01 seconds, providing immediate road illumination without delay.
  • Extended Lifespan: Offers a lifespan of up to 50,000 hours, which is 10 times that of HID bulbs.
  • CANBUS Error-Free: Intelligent CANBUS System designed to prevent radio interference and ensure compatibility with 99% of vehicles (e.g., BMW, Audi, Mercedes-Benz).
  • Plug and Play: Designed for easy, non-destructive installation, directly replacing the original bulb.
  • Sharp Cut-off Line: Effectively avoids glare, significantly improving driving safety.
  • IP68 Waterproof Rating: Works reliably in rainy, snowy, windy, or foggy conditions.
  • Upgraded Copper Tube: Double copper tubes and copper plates effectively suppress light decay for continuous lighting.

Specifications

AttributeValue
Voltage12V-24V
SocketsD1S, D1R, D2S, D2R, D3S, D3R, D4S, D4R, D5S, D8S
LED Chips30PCS 9073 Two-sided LED CSP Chips
Color Temperature6000K
Luminous Flux1,800,000LM
Wattage1500W
System Lifespan50,000 hours
Product MaterialAviation aluminum
Waterproof RatingIP68
Cooling MethodDouble Copper Tube + double ball fan cooling
Applicable Ambient Temperature-45℃ to 95℃ (-49°F to 203°F)
CANBUSCANBUS No Error
Car Brand CompatibilityUniversal (Fits 99% of vehicle models)
OriginMainland China
CertificationE-Mark, CE

Pre-Installation Check: Important Notes

  • This product is only suitable for upgrading original D-Series Xenon headlight models. It is NOT suitable for halogen headlight models.
  • Currently compatible models include: D1S, D1R, D2S, D3S, D3R, D4S, D4R, D5S, D8S.
  • Thorough preparations before the upgrade are crucial for successful installation.

Installation Steps

Watch the official installation video for a general overview:

Video: Demonstration of LED headlight bulb components and installation process.

Installation for D1S, D3S, D8S Models

  1. Rotate the Light Bulb Counter-Clockwise (to remove): Gently rotate the existing light bulb counter-clockwise to detach it from its housing.

    Step 1: Rotating the old bulb counter-clockwise for removal.

    Image: Hand rotating the existing D1S/D3S/D8S bulb counter-clockwise to remove it from the headlight assembly.

  2. Remove the Original Car Card Slot: Carefully remove the card slot that holds the original bulb in place.

    Step 2: Removing the original car card slot.

    Image: Hand removing the card slot from the headlight assembly.

  3. Install the Removed Socket into the New LED Bulb: Attach the previously removed socket onto the new LED bulb.

    Step 3: Installing the removed socket onto the new LED bulb.

    Image: Hand attaching the socket to the base of the new LED bulb.

  4. Plug the Original Car Connector into the Bulb: Connect the original car's electrical connector to the new LED bulb.

    Step 4: Plugging the original car connector into the new LED bulb.

    Image: Hand plugging the car's connector into the new LED bulb's base.

  5. Align and Install the Booth Arrow Position: Ensure the new bulb is correctly aligned with the headlight assembly, matching the arrow positions, and then install it securely.

    Step 5: Aligning and installing the new LED bulb into the headlight assembly.

    Image: Hand aligning the new LED bulb with the headlight housing and securing it.

Installation for D2S, D2R, D4S, D4R Models

  1. Rotate Counter-Clockwise to Remove the Plug: Rotate the plug of the existing bulb counter-clockwise to remove it.

    Step 1: Rotating the plug counter-clockwise for removal.

    Image: Hand rotating the plug of the existing D2S/D2R/D4S/D4R bulb counter-clockwise.

  2. Remove the LED Bulb Socket Separately: Detach the LED bulb from its socket.

    Step 2: Removing the LED bulb socket separately.

    Image: Hand separating the LED bulb from its socket.

  3. Align the Slot on the Card Holder with the Slot on the Car: Ensure the card holder's slot aligns with the corresponding slot in the car's headlight assembly.

    Step 3: Aligning the card holder slot with the car's slot.

    Image: Hand aligning the card holder with the headlight assembly.

  4. Insert the Bulb and Twist to Secure: Insert the new LED bulb into the assembly and twist it clockwise to secure it in place.

    Step 4: Inserting the new LED bulb and twisting to secure.

    Image: Hand inserting the new LED bulb and twisting it into position.

  5. Connect the Power Cord by Rotating Counter-Clockwise: Connect the power cord to the bulb by rotating it counter-clockwise until it locks securely.

    Step 5: Connecting the power cord by rotating counter-clockwise.

    Image: Hand connecting the power cord to the LED bulb by rotating it.

Installation for D5S Models

  1. Turn the Bulb to the Left to Remove It: Rotate the existing D5S bulb to the left to remove it from the headlight assembly.

    Step 1: Turning the D5S bulb to the left for removal.

    Image: Hand rotating the D5S bulb to the left to remove it.

  2. Press the Arrow Position and Pull Out the Plug: Locate the arrow position on the plug, press it, and then pull out the plug.

    Step 2: Pressing the arrow position and pulling out the plug.

    Image: Hand pressing the arrow on the plug and pulling it out.

  3. Rotate the Light Bulb to the Right to Install: Insert the new D5S LED bulb and rotate it to the right to secure it in the headlight assembly.

    Step 3: Rotating the new D5S LED bulb to the right to install.

    Image: Hand rotating the new D5S LED bulb to the right to install it.

Operating Instructions

Once installed, the ZMINR LIGHT D-Series LED Headlight Bulbs operate as a direct replacement for your original Xenon bulbs. They are designed for immediate, full brightness upon activation.

  • Instant On: The bulbs light up in 0.01 seconds, providing instant illumination.
  • Brightness: Experience 800% brighter light compared to original HID headlights for superior visibility.
  • Beam Pattern: The bulbs produce a sharp cut-off line to prevent glare for oncoming traffic while providing a wide and far illumination range.
Comparison of LED low beam and high beam illumination.

Image: Visual comparison of low beam (left low right high, safe meeting, full light, good paving effect) and high beam (irradiation distance is far, illumination range is wide, safety factor greatly improved) performance.

Maintenance

  • Cleaning: Periodically clean the exterior of the headlight assembly to ensure maximum light output. Avoid harsh chemicals that could damage the lens.
  • Waterproof Design: The IP68 waterproof and dust-proof grade ensures the bulbs work well in various weather conditions (rain, snow, wind, fog). No special waterproofing maintenance is typically required for the bulb itself.
  • Cooling System: The integrated Shark Fin + Fan Cooling System and Vacuum Heat Transfer Copper Pipe are designed for optimal heat dissipation. Ensure no debris obstructs the fan or heatsink fins.
IP68 waterproof test of the LED headlight bulb.

Image: The LED headlight bulb undergoing an IP68 waterproof test, demonstrating its resistance to water and dust.

Diagram of the efficient cooling system with sandwich copper heat conduction and silent turbo cooling fans.

Image: Diagram illustrating the efficient cooling system, featuring sandwich copper heat conduction, newest top automotive-grade LED chip, and silent and powerful turbo cooling fans for faster and quieter operation, with cold air input.

Diagram showing the upgraded copper tube for heat dissipation.

Image: Diagram comparing 1st generation (single sandwich copper tube, poor heat dissipation) and 2nd generation (sandwich copper + signal copper tube, rapid cooling) heat dissipation, highlighting the upgraded copper tube design to suppress light decay.

Troubleshooting

  • CANBUS Errors: The intelligent CANBUS system is designed to be error-free for 99% of vehicles. If you encounter dashboard error messages, ensure the bulbs are correctly installed and the original ballast is properly connected.
  • Radio Interference: The upgraded built-in driver with EMC system reduces the possibility of radio interference. If interference occurs, check connections and ensure proper grounding.
  • Flickering or Warning Lights: The CUP decoding feature is designed to prevent flickering and warning lights. If these issues arise, re-check the installation steps and connections.
  • Light Output Issues: If the light output is not as expected, verify that the bulb is seated correctly and that the power connection is secure.
Diagram showing upgraded built-in driver features like interference resistance, temperature control, non-destructive installation, and CUP decoding.

Image: Diagram highlighting the upgraded built-in driver with features such as interference resistance (no impact on navigation, radio, or Bluetooth), TEC temperature control (monitors working temperature and smartly adjusts cooling), non-destructive installation (replaces bulbs directly without altering wiring), and CUP decoding (compatible with in-car computers, flicker-free, and warning-free).

User Tips

  • Many users find these bulbs simple to fit, matching the description exactly.
  • The road lighting effect is highly praised for its clarity and brightness, making it a recommended upgrade.
  • Ensure your vehicle is compatible with D-Series Xenon headlight upgrades before purchase.

Warranty and Support

This product comes with a 1-year warranty.

For any technical assistance or support inquiries, please refer to the seller's contact information provided at the point of purchase.

A detailed user manual in PDF format is also available for download: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.