Instruction Manual

1. Introduction

This manual provides essential information for the safe and proper installation, use, and maintenance of your A60M Motorcycle Side Cover Frame Engine Guard Fairing. Please read this manual thoroughly before installation and retain it for future reference.

2. Safety & Warnings

Warning!

• This product is intended for adult use only.
• Keep out of reach of children and pets to prevent accidental injury or ingestion of small parts.
• Always ensure the installation is correct and secure before operating the motorcycle.
• If you observe any abnormal noise or equipment error after installation, immediately stop the motorcycle and inspect the fairing and mounting.
• Follow all instructions for proper use. Misuse may lead to harm or damage.
• Store the product in a dry and shady place, away from high temperatures, humidity, and direct sunlight when not in use.

3. Product Specifications

Note: Due to light reflection and different display settings, the color of the item in images may appear slightly different from the actual product. A measurement error of +/- 1-3cm is allowed.

4. Package Contents

The package includes the following items:

• 1 Set x Fairing Side Cover (Left & Right)
• Mounting Hardware (Clamps, Bolts, Nuts, Washers, Adhesive Strips)

5. Installation

While specific instructions may vary based on your motorcycle's exact configuration, the general steps for installing the side cover fairing are as follows. It is recommended to consult a professional mechanic if you are unsure about any steps.

1. Prepare the Motorcycle: Ensure the motorcycle is stable and turned off. Allow any hot components to cool down.
2. Identify Mounting Points: Locate the appropriate frame or engine guard sections on both the left and right sides of your HONDA Rebel CMX 250/300/500 where the fairings will attach.
3. Attach Adhesive Strips (if applicable): Apply the provided adhesive strips to the inner surfaces of the fairing panels where they will contact the motorcycle frame, if necessary, to prevent scratching and reduce vibration.
4. Position the Fairing: Carefully position one fairing panel against the designated area on the motorcycle.
5. Secure with Hardware: Use the clamps, bolts, nuts, and washers provided to securely fasten the fairing panel to the motorcycle frame. Ensure all connections are snug but do not overtighten, which could damage the fairing or frame.
6. Repeat for Other Side: Install the second fairing panel on the opposite side of the motorcycle following the same procedure.
7. Final Check: After installation, double-check all mounting points to ensure they are secure and that the fairings do not interfere with any moving parts or controls. Refer to the Safety & Warnings section regarding checking for correct installation.

6. Usage and Care

The A60M Side Cover Frame Engine Guard Fairing is designed to provide aesthetic enhancement and a degree of protection to your motorcycle's engine area. Once installed, it requires minimal active 'operation'.

• Before First Use: Ensure the product is free from any damage before installation and initial use.
• Regular Inspection: Periodically check the fairing and its mounting hardware for any signs of loosening, damage, or wear. Tighten any loose fasteners as needed.
• Cleaning: Clean the fairing with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents that could damage the ABS material or finish.
• Storage: If the fairing is removed for any reason, store it in a dry and shady place, away from high temperatures, humidity, and direct sunlight. Keep it away from children.

7. Maintenance

Beyond regular cleaning and inspection, the ABS fairing panels require little specific maintenance. Focus on maintaining the integrity of the mounting hardware.

• Fastener Check: Regularly inspect all bolts, nuts, and clamps for tightness. Vibrations from motorcycle operation can cause fasteners to loosen over time.
• Damage Assessment: In case of impact or fall, thoroughly inspect the fairing for cracks or severe damage. Replace damaged components to maintain protection and appearance.
• Corrosion Prevention: Ensure metal mounting hardware is kept clean and dry to prevent corrosion, especially if riding in wet conditions.

8. Troubleshooting

Most issues related to the fairing are installation-dependent.

• Fairing is Loose: If the fairing feels loose or rattles, re-check all mounting bolts and clamps. Ensure they are tightened securely.
• Abnormal Noise: If you hear abnormal noise after installation, immediately stop the motorcycle. Inspect the fairing for contact with other motorcycle components or loose mounting. Adjust position or tighten fasteners as necessary. If the noise persists, consult a professional.
• Fairing Does Not Fit: Double-check the product's fitment specifications against your motorcycle's make, model, and year. Ensure you have the correct fairing for your HONDA Rebel CMX 250, 300, or 500 (2017-2021).

9. Manufacturer & Support Information

For inquiries or support regarding this product, please contact the manufacturer or their authorized representative:

10. CE Marking

The product bears the CE marking, indicating its conformity with health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).