COOSPO H808S

Contents

COOSPO H808S Heart Rate Sensor User Manual

Model: H808S

1. Introduction

The COOSPO H808S is a high-precision heart rate sensor designed to monitor your heart rate during various physical activities. It features dual-mode connectivity (Bluetooth and ANT+) for compatibility with a wide range of devices and applications.

COOSPO H808S Heart Rate Sensor

Image: COOSPO H808S Heart Rate Sensor with strap.

2. Product Features

  • Dual-Mode Connectivity: Supports both Bluetooth and ANT+ for broad compatibility.
  • Wide Compatibility: Connects with smart sports watches, GPS bike computers, and fitness equipment.
  • Third-Party APP Support: Compatible with over 200 applications including CoospoRide, Strava, Zwift, Peloton, Wahoo, Polar Beat, Runkeeper, Rouvy.
  • LED and Beep Reminders: Provides clear indications for working status and connection.
  • Waterproof Rating: IP67.
BLE & ANT+ Connectivity

Image: Diagram showing BLE & ANT+ Connectivity with smartwatches, GPS bike computers, and fitness equipment.

Third-party APP Compatible

Image: Illustration of the heart rate sensor connected to a smartphone displaying heart rate data, highlighting third-party app compatibility.

3. Setup and Installation

3.1. Wearing the Heart Rate Sensor

  1. Connect the heart rate sensor to the chest strap, ensuring the left mark "L" faces left.
  2. Adjust the length of the chest strap for a snug yet comfortable fit. Ensure the wet electrode area is tightly adhered to the skin, and the sensor's front face is upright at the center of the chest.
  3. When you hear two "beep" prompts, the LED light flashes green, indicating the heart rate sensor is correctly worn and has detected a heart rate signal.
Wearing the Heart Rate Sensor Diagram

Image: Diagram illustrating how to wear the heart rate sensor on the chest, with the 'L' mark on the left side.

3.2. Battery Replacement

If the device cannot be detected, consider replacing the battery.

  1. Use a coin to block the groove and rotate it in the "OPEN" direction to open the battery cover.
  2. Remove the old battery and dispose of it properly according to local environmental regulations.
  3. Place the new battery correctly into the battery compartment (positive side up). Use a coin to rotate the battery cover counterclockwise along the "CLOSE" direction until it is fully covered.

Warning: To avoid danger, batteries should be kept out of reach of children.

Image: Diagram showing the steps for battery replacement, including opening the cover with a coin, removing the old battery, and inserting a new one (part of the multi-diagram image).

4. Operating Instructions

Note: Please wear the heart rate sensor first before attempting to pair it with your phone. If you do not wear the sensor, it will be in sleep mode and cannot be found via Bluetooth.

4.1. Connecting to a Smartphone App (Bluetooth)

  1. Enable Bluetooth and grant required permissions on your phone. Locate the sensor settings menu within your preferred fitness app (e.g., "COOSPO Sports" app).
  2. In the app, navigate to: "COOSPO Sports" App > My > Devices > Add Device > App Bind Sensor > Heart Rate > H808S.
  3. Important: Do not pair the sensor in your phone's system Bluetooth settings.
  4. Launch the app and connect to the device.
  5. When the sensor is connected, the LED will flash blue.

4.2. Connecting to an ANT+ Watch or Device

  1. Ensure your ANT+ device (e.g., sports watch, bike computer) has ANT+ enabled.
  2. Search for and add "H808S" in the ANT+ device list on your watch or device.

4.3. LED Light and Beep Reminders

The sensor provides audio and visual cues for its status:

  • Beep-Beep: Two short beeps indicate the sensor has started working.
  • Long Beep: One long beep indicates the sensor has stopped working.
  • LED Indicator:
    • Flash in blue: Connected (via Bluetooth).
    • Flash in green: Disconnected.
LED Light and Beep Reminding

Image: Diagram explaining the LED indicator colors (blue for connected, green for disconnected) and beep patterns (two short beeps for start, one long beep for stop).

5. Maintenance

The H808S is a high-tech electronic device. Following these product care instructions will ensure its stability and extend its service life.

5.1. Heart Rate Sensor Care

  • After each use, remove the sensor from the chest strap.
  • Wipe the sensor with a soft, dry towel.
  • Do not use cleaning chemicals on the sensor.

5.2. Chest Strap Care

  • After each use, rinse the chest strap with running water and dry it thoroughly.
  • Do not wash or dry the chest strap using a washing machine or dryer.
  • Do not use chemical cleaners, as they may cause the chest strap to age rapidly and shorten its lifespan.
  • Do not stretch the chest strap or bend the electrode area vigorously.

5.3. Storage

Do not store the heart rate sensor in damp or air-tight environments to prevent sudden oxidation. Store it in a cool and dry place.

6. Troubleshooting

  • Sensor Not Detected:
    • Ensure the sensor is worn correctly and making good skin contact.
    • Check if the battery needs replacement.
    • Verify Bluetooth/ANT+ is enabled on your device and you are pairing through the app (for Bluetooth) or device settings (for ANT+).
    • Make sure the sensor is not already connected to another device.
  • Inaccurate Readings:
    • Ensure the electrodes are moist (e.g., with water or electrode gel) for better conductivity.
    • Check for proper fit; the strap should be snug but not overly tight.
    • Avoid strong electromagnetic interference.
  • LED Not Lighting Up:
    • Check battery level and replace if necessary.
    • Ensure the sensor is properly attached to the strap and worn on the body to activate.

7. Specifications

FeatureDescription
ModelH808S
TypeChest wear Heart Rate Sensor
MaterialRubber (sensor), Fabric (strap)
ConnectivityBluetooth, ANT+
Waterproof RatingIP67
Sensor Dimensions (approx.)Length: 2.36 inches (60mm), Width: 1.37 inches (35mm), Height: 0.59 inches (15mm)
Strap Adjustable Range (approx.)25.6 - 37.4 inches (65 - 95 cm)
OriginMainland China
COOSPO H808S Dimensions

Image: Diagram showing the dimensions of the COOSPO H808S sensor (2.36 in length, 1.37 in width, 0.59 in height) and the adjustable strap range (25.6-37.4 inches).

8. Warranty and Support

COOSPO products are manufactured to high standards and are subject to strict quality control. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms, duration, and support inquiries, please refer to the official COOSPO website or contact your retailer.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.