saimili LED COB Light Strip USB Touch Sensor

Contents

SAIMILI 5V COB LED Light Strip with USB Touch Sensor Dimmer

User Instruction Manual

Introduction

Thank you for purchasing the SAIMILI 5V COB LED Light Strip with USB Touch Sensor Dimmer. This product is designed to provide versatile and efficient lighting for various applications, including kitchens, bedrooms, cabinets, wardrobes, closets, and stairs. Please read this manual carefully before installation and use to ensure proper operation and longevity of your light strip.

Safety Information

  • Ensure the power source is 5V DC. Using an incorrect voltage may damage the product.
  • Do not immerse the light strip or USB connector in water, as it is rated IP20 (non-waterproof).
  • Keep the light strip unfolded during operation to prevent overheating.
  • Avoid looking directly at the illuminated LEDs for extended periods.
  • Keep out of reach of children.

Package Contents

  • COB LED Light Strip (selected length and color)
  • USB Cable with Touch Sensor Switch

Note: Packaging may vary as shown in the image below.

Two different packaging types for the COB LED light strip
Figure 1: Example of product packaging (random delivery).

Specifications

Product Specifications
Feature Description
Product Type USB 5V COB LED Strip Light
Working Voltage DC 5V
Lamp Beads COB
Available Lengths 1m, 2m, 3m, 4m, 5m
COB Width 8mm (0.31 inch)
LEDs Quantity 320 LEDs/meter
Luminous Flux 100 LM/W
Waterproof Grade IP20 (Not waterproof)
Color Rendering Index (RA) >90
Light Color Options Cold White (6000K), Natural White (4000K), Warm White (3000K)
Power Generation Touch
Smart Device No
Batteries Included No
Power Source DC
Certification CE, EMC, ROHS
Diagram showing product specifications including COB width and cutting points
Figure 2: Product dimensions and cutting points.

Setup Instructions

  1. Prepare the Surface: Clean the area where you intend to install the light strip with a cloth to ensure it is free of dust and debris.
  2. Cut to Length (Optional): If a shorter length is desired, cut the LED strip only at the designated cutting marks. Refer to Figure 2 for visual guidance.
  3. Remove Adhesive Backing: Carefully peel off the adhesive backing from the light strip.
  4. Attach the Strip: Firmly press the light strip onto the desired clean surface.
  5. Connect Power: Connect the USB plug of the touch sensor cable to a 5V USB power port. Ensure the input side of the switch cable is connected to the power supply and the output side is connected to the LED strip.
Close-up of the USB touch switch and the COB light strip, showing the USB connector
Figure 3: USB connector and touch switch.

Operating Instructions

The light strip is controlled via the integrated touch sensor switch on the USB cable.

  • Turn On/Off: Briefly touch the sensor (less than 3 seconds) to toggle the light strip On or Off.
  • Adjust Brightness (Stepless Dimming): Touch and hold the sensor for more than 3 seconds. The brightness will gradually increase to its highest level or decrease to its lowest level. Release your finger when the desired brightness is reached.
Diagram explaining short touch for on/off and long touch for dimming on the touch switch
Figure 4: Touch switch operation for On/Off and dimming.

For a visual demonstration of the product's features and operation, please watch the video below:

Video 1: Product demonstration showing installation and operation.

Maintenance

  • To clean the light strip, gently wipe it with a dry or slightly damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Ensure the light strip is disconnected from the power source before cleaning.

Troubleshooting

  • Switch Not Working: When testing the touch switch, avoid holding the entire switch body. Only touch the sensor area.
  • Dead LEDs After Cutting: Ensure you cut the LED strip only at the designated cutting marks. Incorrect cutting will result in dead LEDs and cannot be repaired.
  • Overheating: Always keep the LED strip fully unfolded before and during use. Rolling it up or keeping it coiled while powered on can lead to overheating.
  • Color Temperature Variation: Slight differences in color temperature may occur between different production batches of the LED strip. This is a normal characteristic and not considered a quality problem.
  • Soldering Marks: Soldering is a common manufacturing process in electronic products and visible soldering points are not indicative of a quality issue.

User Tips

  • For optimal adhesive performance, ensure the installation surface is completely smooth, clean, and dry.
  • Before removing the adhesive backing, plan your desired installation path and test the strip's length and placement.
  • Use a reliable 5V USB power adapter (e.g., phone charger, power bank, computer USB port) to ensure stable performance.
  • Experiment with the stepless dimming feature to create various ambiances for different occasions or times of day.
  • The ultra-thin design and even light distribution (no light points) make this strip ideal for subtle accent lighting in tight spaces.
Image showing the COB light strip with even glowing and no visible light points
Figure 5: Even glowing, soft and comfortable light from the COB strip.

Warranty and Support

This product comes with a standard manufacturer's warranty. For any issues, technical support, or warranty claims, please contact the seller or refer to your purchase documentation for specific details.

A PDF user manual is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.