IKSLED AC7036T-F47

Contents

User Manual for IKSLED AC Sensor Control Switch

Model: AC7036T-F47

1. Introduction and Product Overview

The IKSLED AC Sensor Control Switch (Model: AC7036T-F47) is a touch-sensitive switch designed to control various AC loads, including LED lights and energy-saving lamps, through non-metallic surfaces. It features a penetrable design, allowing the sensor to be hidden behind materials up to 3 cm thick. This manual provides detailed instructions for safe installation, operation, and maintenance of the device.

IKSLED AC Sensor Control Switch overview showing the sensor and control unit, with a hand demonstrating touch functionality through a surface.
Figure 1: Product Overview - Touch functionality through a surface (partition thickness < 3cm).

2. Safety Information

WARNING: High Voltage. Risk of Electric Shock.

  • The sensor cable carries high voltage. Ensure the power is disconnected from the main supply during all installation, removal, and maintenance procedures.
  • The circuit board inside the sensor carries high voltage. Do not disassemble the housing or attempt to directly touch the circuit board. Disassembly voids the warranty and poses a severe safety risk.
  • Installation should only be performed by qualified personnel in accordance with local electrical codes and regulations.
  • Do not exceed the maximum power rating of 400W.
Safety warning image showing a disassembled sensor with a red cross, indicating 'Do not disassemble'.
Figure 2: Safety Warning - Do not disassemble the sensor unit.

3. Product Features

  • Touch On/Off Functionality: Simple touch to turn on, touch again to turn off.
  • Hidden Installation: Sensor can be installed behind non-metallic surfaces up to 3 cm thick.
  • Wide Voltage Compatibility: Supports 100V-240V AC input and output.
  • High Power Capacity: Maximum power output of 400W.
  • Versatile Application: Suitable for controlling LED lights, energy-saving lamps, exhaust fans, water pumps, and other AC loads.
  • Non-Dimmable: Provides simple ON/OFF control only.
Image showing a hand touching a surface above a hidden sensor, illustrating the touch on/off function.
Figure 3: Touch On/Off Functionality.
Image showing the control unit and various compatible loads like light bars, LED lights, exhaust fans, water pumps, and high power lamps.
Figure 4: Compatible Loads (Do not over-power).

4. Specifications

Attribute Value
Model NumberAC7036T-F47
Brand NameIKSLED
Switch TypeTouch On/Off Switch
MaterialPlastic
Voltage100V-240V AC
Max Power400W
FunctionTouch to turn on; touch again to turn off.
Sensor Diameter46mm
Sensor Thickness8mm
Penetration DepthMax. 3 cm
CertificationVDE, SAA, RoHS, LVD, EMC, CE
EU LVD VoltageHigh voltage: Above 50Vac or 75Vdc
Warranty1 Year
Product dimensions diagram showing the control unit (70mm length, 36mm width, 23mm height) and the sensor (4.6cm diameter, 6mm thickness).
Figure 5: Product Dimensions.

5. Setup and Installation

Follow these steps carefully to install your IKSLED AC Sensor Control Switch. Ensure power is disconnected before beginning installation.

5.1. Wiring Diagram

The control unit has input terminals (L in, N in) and output terminals (L out, N out). Connect your power supply to the input and your load to the output. For 12V/24V lamps, a constant voltage adapter is required between the switch output and the lamps.

Detailed connection diagram for the AC Sensor Control Switch, showing input from a wall socket, output to a 100V-240V lamp, 12V/24V lamps via a constant voltage adapter, and an AC1100V-240V load.
Figure 6: Connection Diagram for various loads.

5.2. Sensor Placement

  1. Identify the desired touch-sensitive area on the back side of your non-metallic panel (e.g., wooden board, plastic).
  2. Peel off the backing from the double-sided tape on the sensor.
  3. Securely fix the sensor in place on the back side of the panel, ensuring it is directly behind the intended touch area.
  4. Ensure the panel thickness is within the specified penetration depth (max. 3 cm) for optimal performance.
Installation steps showing peeling off double-sided tape, fixing the sensor, and mounting it on the back side of a panel.
Figure 7: Sensor Installation Steps.

5.3. Powering On

After all connections are made and the sensor is securely fixed, you may connect the power supply. Test the functionality by touching the designated area on the front of the panel.

Video 1: Installation and Demonstration of the Touch Sensor Switch. This video shows the complete setup process and how the touch function operates.

6. Operating Instructions

Once installed and powered, the IKSLED AC Sensor Control Switch operates with a simple touch gesture:

  • To Turn On: Lightly touch the designated area on the surface where the sensor is mounted. The connected load will turn on.
  • To Turn Off: Lightly touch the same designated area again. The connected load will turn off.

This switch provides basic ON/OFF functionality and is not designed for dimming or other advanced controls.

7. Maintenance

The IKSLED AC Sensor Control Switch is designed for low maintenance. Follow these guidelines to ensure longevity:

  • Keep the installation area clean and free from excessive dust or moisture.
  • Do not expose the control unit or sensor to extreme temperatures or direct water contact.
  • Regularly check wiring for any signs of damage or loose connections. Disconnect power before inspection.
  • Do not attempt to open or repair the device. Refer to the Warranty and Support section for service.

8. Troubleshooting

Problem Possible Cause Solution
Device does not turn on/off with touch.
  • No power supply.
  • Incorrect wiring.
  • Sensor not securely fixed.
  • Panel material too thick or unsuitable.
  • Sensor or control unit is defective.
  • Check power connection to the control unit.
  • Verify wiring according to the Connection Diagram (Figure 6).
  • Ensure the sensor is firmly attached to the panel.
  • Confirm panel thickness is within 3 cm and made of non-metallic material. Test with a thinner material if possible.
  • If all else fails, contact support.
Load flickers or behaves erratically.
  • Load exceeds maximum 400W.
  • Loose wiring connection.
  • Incompatible load type (e.g., dimmable lights).
  • Reduce total load to below 400W.
  • Check and secure all wiring connections.
  • Ensure the connected load is compatible with a simple ON/OFF switch.

9. User Tips

  • Penetration Depth: While rated for up to 3 cm, actual effective penetration depth can vary depending on the material density and composition. Some users have reported reduced sensitivity with certain materials, even at thinner dimensions. It is recommended to test the sensor's responsiveness with your specific material before final installation.
  • Installation Order: Always complete all wiring and sensor placement steps before connecting the device to the main power supply. This ensures safety and proper initialization.
  • Cable Length: The cable connecting the sensor to the control unit is relatively short. Plan your installation location accordingly to ensure the cable can reach both components without strain.

10. Warranty and Support

The IKSLED AC Sensor Control Switch comes with a 1-year warranty from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by improper installation, misuse, unauthorized modification, or disassembly.

For technical support, warranty claims, or any questions regarding the product, please contact the seller or manufacturer directly. You may also refer to the contact number provided in the original product documentation: 0086 13421343580.

Please have your purchase details and model number (AC7036T-F47) ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.