1. Introduction
This manual provides comprehensive instructions for the safe and effective use of your Autel MaxiCOM MK808BT PRO Car Diagnostic Tool. Please read it carefully before operation.
1.1 Trademarks
Autel®, MaxiSys®, MaxiDAS®, MaxiPRO®, MaxiRecorder®, MaxiCOM®, and MaxiCheck® are trademarks of Autel Intelligent Technology Corp., Ltd., registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.
1.2 Copyright Information
No part of this manual may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of Autel.
1.3 Disclaimer of Warranties and Limitation of Liabilities
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Autel reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Autel will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.
1.4 Safety Information
For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device.
There are various procedures, techniques, tools, and parts required for servicing vehicles, as well as the skills of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician's responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested.
Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Be sure to read, understand, and follow all safety messages and instructions in this manual.
1.4.1 Safety Messages
Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders.
1.4.2 Safety Instructions
The safety messages herein cover situations Autel is aware of at the time of publication. Autel cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety.
DANGER: When an engine is operating, keep the service area WELL VENTILATED or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to serious personal injury or loss of life.
SAFETY WARNINGS:
- Always perform automotive testing in a safe environment.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area, for exhaust gases are poisonous.
- Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.
- Be extra cautious when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
- Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.
- Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.
- To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.
- Do not place the test equipment on the distributor of the vehicle. Strong electro-magnetic interference can damage the equipment.
2. Setup
2.1 General Introduction
The MaxiCOM MK808BT Pro is a powerful auto diagnostics and service tool featuring a quad-core processor, a 7.0-inch LCD capacitive touchscreen, and running on the Android multitasking operating system. It is designed to quickly read and clear DTCs for all available modules across a wide range of vehicle makes and models. It offers superior functions including Oil Reset, EPB, SAS, BMS, and DPF.
The system consists of two main components:
- MK808BT Pro Tablet: The central processor and monitor for the system.
- MaxiVCI Mini: A vehicle communication interface used for accessing vehicle data.
This manual describes the construction and operation of both devices and how they work together to deliver diagnostic solutions.
2.2 MaxiCOM MK808BT Pro Tablet
2.2.1 Function Description
The tablet features a 7.0" LCD touchscreen, ambient light sensor, power LED, and vehicle communication LED. The power LED indicates battery level and charging status (green for >90% charge, yellow for <90% charge, red for <15% charge or abnormality). The vehicle communication LED flashes green when communicating with the vehicle.

Figure 2-1: Autel MaxiCOM MK808BT PRO Tablet Front View

Figure 2-2: New MaxiCOM MK808BT PRO Features Overview
The back of the tablet includes a collapsible stand for hands-free viewing and a MaxiVCI Mini Holder.

Figure 2-3: MaxiCOM MK808BT PRO Hardware Comparison
The top view of the tablet shows the following ports:
- USB Type-C Port: Supports charging.
- Micro SD Card Slot: Holds the Micro SD card (supports up to 64GB).
- HDMI (High-Definition Multimedia Interface) Port
- USB Port
- Power/Lock Button: Turns the device on/off with a long press, or locks the screen with a short press.
2.2.2 Power Sources
The tablet can be powered by its internal 3.7 V/5000 mAh lithium-polymer battery, providing about 6.5 hours of continuous operation when fully charged. It can also be powered and charged from a wall socket using the included USB Type-C cable and external power adapter.
2.3 MaxiVCI Mini
The MaxiVCI Mini is a vehicle communication interface (VCI) that connects to the vehicle's Data Link Connector (DLC) for vehicle data transmission.
2.3.1 Function Description
The MaxiVCI Mini features a 16-Pin Vehicle Data Connector, Power LED, Connection LED, and Mini USB Port. The unit powers on whenever it is connected to the vehicle's DLC.

Figure 2-4: MaxiCOM MK808BT Pro Packing List
MaxiVCI Mini LED Indicators:
| LED | Color | Description |
|---|---|---|
| Status LED | Flashing Green | The tester is communicating via USB cable. |
| Flashing Blue | The tester is communicating via Bluetooth. | |
| Flashing Red | Battery clamps are connected to the wrong battery terminals. | |
| Power LED | Solid Green | The tester is powered on and the battery is sufficiently charged. |
| Flashing Green | The tester is charging. (Turns solid green when battery is fully charged.) | |
| Solid Red | The device is in boot mode. | |
| Flashing Red | The battery level is low. Please charge. |
2.4 Other Accessories
The MaxiCOM MK808BT PRO comes with the following accessories:
- Mini USB Cable: Supports testing.
- USB Type-C Cable: Supports charging.
- External Power Adapter: Connects the tablet to an external DC power port for power supply.
3. Operation
3.1 Getting Started
Ensure the tablet is sufficiently charged or connected to an external power supply.
3.1.1 Powering Up
Long press the Power/Lock button on the top-right side of the tablet to power on the unit. The power LED will illuminate green. The system boots up and displays the lock screen. Slide the screen up to enter the MaxiCOM Job Menu.

Figure 3-1: MaxiCOM Job Menu
The MaxiCOM Job Menu provides access to various applications:
| Button | Name | Description |
|---|---|---|
| Diagnostics | Accesses diagnostic functions menu. | |
| Service | Accesses special functions menu. | |
| Data Manager | Accesses the organization system for saved data files. | |
| Settings | Accesses the MaxiCOM system settings menu and general tablet menu. | |
| Update | Checks for the latest update available for the MaxiCOM system and installs new software. | |
| VCI | VCI Manager | Pairs the tablet and the MaxiVCI Mini. Checks communication status and updates VCI firmware. |
| Battery Test | Accesses the Battery Test menu with in-vehicle and out-vehicle tests. | |
| MaxiViewer | Provides quick search for supported functions and vehicles of Autel diagnostic tools. | |
| Support | Launches the Support platform for online service. | |
| Remote Desktop | Configures the unit to receive remote support using TeamViewer. | |
| MaxiVideo | Configures the unit to operate as a video scope device. | |
| Quick Link | Provides associated website bookmarks for product update, service, support. | |
| Autel User Center | Allows account registration, profile viewing/editing, and device linking. | |
| MaxiTools | Includes log collection and factory data reset. | |
| OEM Authorization | Manages permissions for unlocking the OE gateway. |
3.1.2 Powering Down
All vehicle communications must be terminated before shutting down the tablet. A warning message appears if you attempt to shut down the tablet while it is communicating with the vehicle. Forcing a shut-down while communicating may lead to ECU problems on some vehicles. Please exit the Diagnostics application before powering down.
To power down the tablet:
- Long press the Power/Lock button.
- Tap Power Off. The tablet will turn off in a few seconds.
3.1.3 Reboot System
In case of a system crash, long press the Power/Lock button and tap the Restart option to restart the system.
3.2 VCI Manager
The VCI Manager application pairs the tablet with the MaxiVCI Mini, checks communication status, and updates VCI firmware.
3.2.1 VCI Bluetooth Pairing
The MaxiVCI Mini needs to be connected to a vehicle for power during synchronization. Ensure the tablet has sufficient battery power or is connected to an external power supply.
To pair the MaxiVCI Mini with the tablet:
- Power on the tablet.
- Insert the 16-pin vehicle data connector of the MaxiVCI Mini into the vehicle data link connector (DLC).
- Tap the VCI Manager application on the MaxiCOM Job Menu.
- Select VCI BT from the Connection Mode list on the left column.
- Toggle the ON/OFF button to ON. Tap the Scan button at the top-right corner. The device will search for available pairing units.
- The device name may display as "Maxi-" suffixed with a serial number. Select the appropriate device for pairing.
- When pairing is successful, the connection status displayed to the right of the device name is shown as "Connected".
- Once connected, the BT badge displays at the bottom-right corner of the VCI Manager shortcut, and the Connection LED on the MaxiVCI Mini illuminates solid blue, signifying that the tablet is connected and ready for vehicle diagnosis.
- Tap the Home button on the top-left to return to the MaxiCOM Job Menu.
NOTE: A MaxiVCI Mini can only be connected to one tablet at a time, and once connected, it will not be discoverable to other devices.
3.2.2 BAS Bluetooth Pairing
The BT506 battery tester device can be connected with the tablet via Bluetooth. Ensure the BT506 battery tester is sufficiently charged or connected to an external power supply before use.
To pair the Battery Tester with the tablet:
- Power on the diagnostic tablet and the battery tester.
- Connect the red clamp to the positive (+) battery terminal and the black clamp to the negative (-) battery terminal.
- Tap VCI Manager on the MaxiCOM Job Menu of the tablet.
- Select BAS BT from the Connection Mode list on the left column.
- Toggle the Bluetooth ON. Tap Scan at the top-right corner of the screen. The device will start to search for available units to pair with.
- Depending on the type of battery tester, the device name may appear as "Maxi-" suffixed with the battery tester's serial number. Select the appropriate device for pairing.
- When paired successfully, the connection status reads "Connected".
3.2.3 VCI Update
To update the MaxiVCI Mini firmware via tablet:
- Power on the tablet.
- Use a Mini USB cable to connect the MaxiVCI Mini to the tablet.
- Tap the VCI Manager application on the MaxiCOM Job Menu of the tablet.
- Select VCI Update from the Connection Mode list on the left column.
- The current and latest versions of the VCI firmware will display. Tap Update Now to update if available.
To update the MaxiVCI Mini firmware via PC:
- Download the Maxi PC Suite software from www.autel.com > Support > Downloads > Autel Update Tools, and install it onto your PC.
- Use a Mini USB cable to connect the MaxiVCI Mini to the PC.
- Launch the PC Suite and click the MaxiVCI Mini icon in the Device Selection window.
- The PC will automatically recognize the MaxiVCI Mini.
- Click Update to complete the update if available.
3.2.4 BAS Update
Before updating the battery tester firmware, ensure a stable network connection.
To update the battery tester's firmware:
- Power on the diagnostic tablet and the battery tester.
- Connect the battery tester to the tablet via Bluetooth.
- Tap the VCI Manager application on the MaxiCOM Job Menu of the tablet.
- Select BAS Update from the Connection Mode list on the left column.
- The current and latest versions of the battery tester's firmware will display. Tap Update Now to update if available.
NOTE: Do not leave the BAS Update page during upgrade.
4. Diagnostics
The Diagnostics application retrieves ECU information, reads & erases DTCs, and views live data. It accesses the electronic control unit (ECU) for various vehicle control systems, including engine, transmission, antilock brake system (ABS), and airbag system (SRS).
4.1 Establishing Vehicle Communication
Prior to performing diagnostics, ensure the tablet is connected to the test vehicle through the MaxiVCI Mini.
Steps:
- Connect the MaxiVCI Mini to the vehicle's DLC for communication and power.
- Connect the MaxiVCI Mini to the tablet via Bluetooth pairing or Mini USB cable.
- A BT badge or USB cable badge will display at the bottom-right corner of the VCI Manager shortcut, indicating communication is established.
4.1.1 Vehicle Connection
Insert the MaxiVCI Mini into the vehicle's DLC (usually under the dashboard). The MaxiVCI Mini will power on automatically.
NOTE: The vehicle's DLC is not always located under the dashboard. Refer to the vehicle's user manual for DLC location.
4.1.2 VCI Connection
The Power LED on the MaxiVCI Mini will light solid green when connected to the vehicle and ready to communicate with the tablet. The MaxiVCI Mini supports Bluetooth or Mini USB Cable Connection.
Video 4-1: Unboxing and Initial Setup of Autel MaxiCOM MK808BT Pro
4.1.3 No Communication Message
If an "Error" message displays, check the following:
- MaxiVCI Mini is powered up and properly positioned.
- Connection LED is illuminated (Bluetooth or Mini USB).
- For Bluetooth: network is configured correctly, correct MaxiVCI Mini is paired. Try moving closer to the MaxiVCI Mini.
- For Mini USB: cable connection is secure.
- If Power LED is flashing red, contact technical support.
4.2 Vehicle Identification
The MaxiCOM diagnostics system supports four methods for vehicle identification:
- Auto Detect
- Manual Input
- Automatic Selection
- Manual Selection

Figure 4-2: Vehicle Identification Methods
4.2.1 Auto Detect
The system features VIN-based Auto Detect for 2006 and newer vehicles. Tap Diagnostics > VID button > Auto Detect. Confirm VIN or enter manually if incorrect.
4.2.2 Manual Input
For vehicles not supporting Auto Detect, manually enter the VIN. Tap Diagnostics > VID button > Manual Input.
4.2.3 Automatic Selection
After selecting a vehicle manufacturer, the VIN can be automatically acquired. Tap Diagnostics > select manufacturer > Automatic Selection.
4.2.4 Manual Selection
If VIN is not retrievable or unknown, select the vehicle manually. This is a menu-driven process.
4.3 Diagnostic Functions
After vehicle identification, the Diagnostic Menu screen appears, offering functions like Auto Scan and Control Unit.

Figure 4-3: OE-Level All Systems Diagnostics Overview

Figure 4-4: Full OBD-Level Diagnostic Capabilities
4.3.1 Auto Scan
Performs a comprehensive scan of all ECUs to locate system faults and retrieve DTCs.
4.3.2 Control Unit
Allows manual selection of a required control system for testing through a series of choices.
4.3.3 ECU Information
Retrieves and displays specific information for the tested control unit, including unit type, version numbers, and other specifications.
4.3.4 Trouble Codes
Read Codes: Retrieves and displays DTCs from the vehicle's control system. Freeze frame data may also be available.
Erase Codes: Clears all emissions-related diagnostic data, including DTCs and freeze frame data, after repairs. A confirmation screen will appear.
4.3.5 Live Data
Displays real-time PID data from the ECU. Parameters are displayed in the order they are transmitted. Data can be viewed in various display modes: Analog Gauge, Text Mode, and Waveform Graph Mode.
To set a trigger for Live Data:
- Tap the drop-down button on the right of a parameter name.
- Tap the Trigger button.
- Enter MIN and MAX values.
- Tap OK to save.
4.3.6 Active Test (Bi-Directional Control)
Used to access vehicle-specific subsystem and component tests. The tablet sends commands to the ECU to activate actuators, determining system integrity. Examples include cycling A/C clutch, switching interior lights, performing evaporative emissions leak tests, and controlling windows or mirrors.

Figure 4-5: Bi-Directional Control / Active Test
4.3.7 Special Functions (38+ Services)
Performs various component adaptations, recalibrations, or configurations after repairs or replacements. This includes Oil Reset, EPB, TPMS, BMS, Brake bleed, Aftertreatment, Immo keys, Injector, SAS, Suspension, Throttle, WIN DR, ROOF, Seats, Odometer, Lang change, Headlamp, CHG tire size, TEC learn, ABSSRS, Cylinder, VGT learn, Speed & PTO, Clutch, Trans adaptation, Airbag reset, A/F Setting, Automatic Start/Stop, Electronic Water Pump start, EGR, VIN, FRM RESET, Transport Mode, HV Battery, ACC, A/C, Rain/Light Sensor, Reset control unit, CCS/ACC, and more.

Figure 4-6: Hot Services Overview
4.3.8 Generic OBDII Operations
Provides quick access to check DTCs, isolate MIL causes, check monitor status for emissions testing, and perform emissions-related services for OBDII/EOBD compliant vehicles.
4.3.9 Exiting Diagnostics
Always exit the Diagnostics application to terminate all vehicle communications before closing the application or disconnecting the device. Damage to the vehicle's ECU may occur if communication is disrupted.
To exit the Diagnostics application:
- Tap the Back or ESC button to exit step by step.
- Alternatively, tap the Vehicle Swap button on the Diagnostics Toolbar to return to the Vehicle Menu screen.
- From the Vehicle Menu screen, tap the Home button on the top toolbar or the Back button on the Navigation Bar to return to the MaxiCOM Home Menu.
5. Service Functions
The Service application provides quick access to vehicle systems for scheduled service and maintenance tasks. Follow on-screen instructions for execution options and necessary actions.
5.1 Oil Reset Service
Resets the Engine Oil Life system after an oil change, allowing the system to calculate the next optimal oil change interval.
NOTE: Always reset engine oil life to 100%. All required work must be carried out before resetting indicators. For some vehicles, additional service lights can be reset.
5.2 Electric Parking Brake (EPB) Service
Maintains the electronic braking system safely. Applications include deactivating/activating the brake control system, assisting with brake fluid control, opening/closing brake pads, and setting brakes after disc or pad replacement.
EPB Safety: Ensure familiarity with the braking system. Only perform maintenance when the vehicle is stationary and on level ground. Reactivate the EPB control system after maintenance.
5.3 Tire Pressure Monitoring System (TPMS) Service
Allows looking up tire sensor IDs from the vehicle's ECU and performing TPMS replacement and reset procedures.
5.4 Battery Management System (BMS) Service
Evaluates battery charge state, monitors close-circuit current, registers battery replacement, activates vehicle rest state, and charges the battery via the diagnostic socket.
NOTE: This function is not supported by all vehicles. Follow on-screen instructions for sub-functions. Replacement batteries should have the same specifications as the original.
5.5 Steering Angle Sensor (SAS) Service
Permanently stores the current steering wheel position as the straight-ahead position in the SAS EEPROM. Calibration is required after steering wheel replacement, SAS replacement, opening the connector hub, steering linkage/gear work, wheel alignment, or accident repairs.
5.6 Diesel Particle Filter (DPF) Service
Manages DPF regeneration, DPF component replacement teach-in, and DPF teach-in after replacing the engine control unit. The ECM monitors driving style for regeneration. A service regeneration can be requested using the diagnostic tool.
IMPORTANT: Before forced DPF regeneration, ensure the fuel light is not on, no DPF-relevant faults are stored, the correct engine oil is used, and diesel oil is not contaminated. Obtain a full diagnostic log and read relevant measured value blocks before emergency regeneration.
NOTE: DPF will not regenerate if the engine management light is on or if there is a faulty EGR valve. The ECU must be re-adapted when replacing the DPF or topping up Eolys. If the vehicle needs to be driven for DPF service, a second person is required to observe the tool. Do not drive and observe the scan tool simultaneously.
6. Battery Test
The Battery Test application allows performing in-vehicle and out-vehicle battery tests when the BT506 battery tester is connected to the MaxiCOM MK808BT Pro tablet and a battery. This enables viewing the health status of the vehicle's battery and electrical system.
NOTE: The BT506 battery tester needs to be purchased separately.

Figure 6-1: Wireless Bluetooth Diagnosis Comparison
6.1 MaxiBAS BT506 Battery Tester
6.1.1 Function Description
The BT506 tester includes a Power Button, Status LED, Power LED, USB Port, and Battery Clamp Cable.

Figure 6-2: MaxiBAS BT506 Battery Tester
6.1.2 Power Sources
The BT506 tester can be powered by its internal battery pack or an AC/DC power supply. The AC/DC power supply also charges the internal battery pack.
IMPORTANT: Do not charge the tester when the temperature is below 0°C (32°F) or above 45°C (113°F).
6.1.3 Test Preparation
Before testing, inspect the battery for cracking, buckling, leaking, corroded/loose cables, and dirt/acid on terminals. Repair or replace as needed.
To connect the Battery Tester:
- Connect the red clamp to the positive (+) battery terminal.
- Connect the black clamp to the negative (-) battery terminal.
6.2 In-vehicle Test
Tests batteries installed in a vehicle, including Battery Test, Starter Test, and Generator Test.
IMPORTANT: A disclaimer will appear when first accessing any function. Read and tap Accept to continue.
To start the in-vehicle test:
- Tap Battery Test on the MaxiCOM Job Menu. Select In-vehicle Test.
- Confirm vehicle information and VIN.
- Confirm battery information (voltage, type, standard, capacity). Tap Next.
6.2.1 Battery Test
Follow on-screen instructions, check boxes for completed tasks, and tap Start Testing. Results include a color-coded summary and test data (Good Battery, Good & Recharge, Charge & Retest, Bad Cell, Replace Battery).
NOTE: Complete the battery test before proceeding to starter and generator tests.
6.2.2 Starter Test
Follow on-screen instructions, start the engine, and let it idle. Results indicate cranking normal, current too low, voltage too low, or not started.
6.2.3 Generator Test
Follow on-screen instructions. Results indicate charging normal, output too low, output too high, ripple too large, or no output.
6.3 Out-vehicle Test
Tests batteries not connected to a vehicle to check battery health only.
To start the out-vehicle test:
- Connect tester clamps to battery terminals.
- Tap Battery Test on the MaxiCOM Job Menu. Select Out-vehicle Test.
- Select appropriate battery type, rating standard, and CCA value. Tap Start Testing.
6.3.1 Test Results
Results display in a few seconds, indicating battery status (Good Battery, Good & Recharge, Charge & Retest, Replace Battery, Bad Cell).
7. Data Management
The Data Manager application stores, prints, and reviews saved files; manages workshop and customer information; and keeps test vehicle records. It offers nine main functions.
7.1 Vehicle History
Stores records of test vehicle records, including vehicle information and DTCs from previous diagnostic sessions. Provides direct access to previously tested vehicles.
7.1.1 Historical Test Record
A detailed data form including vehicle information, service record, customer information, and DTCs. Technician Notes may also appear.
NOTE: The MaxiCOM tablet must connect to the MaxiVCI Mini to restart test sessions on previously tested vehicles.
To edit the Historical Test record:
- Tap Data Manager > Vehicle History.
- Select the record thumbnail.
- Tap Edit (pen icon) to start editing.
- Input information or attach files/images.
- Tap Done to save.
7.2 Workshop Information
Allows editing, inputting, and saving detailed workshop information (name, address, phone, remarks) which will appear as the header on printed documents.
7.3 Customer
Creates and edits customer accounts, correlating them with associated test vehicle history records.
7.4 Image
A PNG database containing all captured screenshots. Allows editing, printing, and deleting images.
7.5 Cloud Report
Displays saved reports that can be transferred to the Autel cloud platform and shared via QR Code/email/text message.
7.6 PDF Files
Displays PDF files for local viewing. Uses Adobe Reader for viewing and editing.
NOTE: A user manual for the MaxiCOM MK808BT PRO is available in PDF format at https://manuals.plus/m/21ed98645fcf61dea448cfe05605e592663b5edce03ab59c70091210d56b5da7. This document contains detailed instructions and specifications.
7.7 Review Data
Allows playback of recorded data frames from live data streams.
7.8 Uninstall Apps
Manages software applications installed on the MaxiCOM system. Select an app and tap Delete to remove it.
8. Settings
Access the Settings menu to adjust default settings and view information about the MaxiCOM system.
8.1 Unit
Adjusts the measurement unit for the diagnostic system.
To adjust unit setting: Tap Settings > Unit > select unit.
8.2 Language
Adjusts the display language for the MaxiCOM system. Supports 21 languages including Simplified Chinese, English, Traditional Chinese, Spanish, French, German, Russian, Japanese, Korean, Polish, Portuguese, Swedish, Persian, Turkish, Thai, Vietnamese, Hebrew, Arabic, Indonesian English, Italian, Dutch.

Figure 8-1: Multi-language Support
To adjust language setting: Tap Settings > Language > select language.
8.3 Printing Settings
Configures the tablet to print via network.
To set up printer connection: Tap Settings > Printing Settings > ensure Print via PC-Link is selected.
To install PC Link driver program: Download Maxi PC Suite from www.autel.com > Support > Downloads > Autel Update Tools.
8.4 Report Settings
Synchronizes diagnostics information to vehicle history and forms a diagnostic report for cloud upload. Tap ON/OFF to enable/disable Report Upload to Cloud.
8.5 Push Notifications
Manages notifications. Notification Preferences is on by default for system security warnings.
8.6 Auto Update
Automatically updates OS, MaxiCOM system, and vehicle coverage software. Can be configured to update at a specified time.
8.7 Vehicle List
Sorts vehicles by alphabetical order or frequency of use.
8.8 System Settings
Direct access to Android system settings for wireless, network, sound, display, and security settings.
8.9 About
Provides information on the MaxiCOM diagnostics device, including product name, version, hardware, and serial number.
9. Maintenance
To ensure optimum performance, follow these maintenance instructions:
- Use a soft cloth and alcohol or mild window cleaner to clean the touchscreen. Do not use abrasive cleansers or automotive chemicals.
- Keep devices dry and within normal operating temperatures.
- Dry your hands before using the tablet.
- Do not store the device in humid, dusty, or dirty areas.
- Check housing, wiring, and connectors for dirt and damage before and after each use.
- Wipe device housing, wiring, and connectors clean with a damp cloth after use.
- Do not attempt to disassemble your tablet.
- Do not drop or cause severe impact to the devices.
- Only use authorized battery chargers and accessories. Unauthorized accessories will void the warranty.
- Ensure the battery charger does not contact conductive objects.
- Do not use the tablet near microwave ovens, cordless phones, or medical/scientific instruments to prevent signal interference.
9.1 About Battery Usage
Your tablet is powered by a built-in Lithium-ion Polymer battery. This technology allows recharging without the "battery memory effect."
DANGER: The built-in Lithium-ion Polymer battery is factory replaceable only; incorrect replacement or tampering with the battery pack may cause an explosion.
- Do not use a damaged battery charger.
- Do not disassemble, open, crush, bend, deform, puncture, or shred the battery.
- Do not modify, remanufacture, or attempt to insert foreign objects into the battery.
- Only use specified charger and USB cables. Non-Autel-authorized chargers may lead to device malfunction or failure.
- Avoid dropping the tablet. If damaged, take it to a service center.
- Keep the battery in temperate environments. Do not place it inside a car when it is too hot or too cold.
10. Troubleshooting
10.1 Troubleshooting Checklist
When the tablet does not work properly:
- Ensure the tablet is registered online.
- Ensure system and diagnostic application software are properly updated.
- Ensure the tablet is connected to the Internet.
- Check all cables, connections, and indicators for signal reception.
When battery life is shorter than usual:
- This may happen in areas with low Wi-Fi signal strength. Turn off the device when not in use.
When the tablet cannot be turned on:
- Ensure the tablet is connected to a power source or the battery is charged.
When you are unable to charge the tablet:
- Your charger may be out of order. Contact your nearest dealer.
- You may be attempting to use the device in an overly hot/cold temperature. Try changing the charging environment.
- Your device may not have been connected to the charger properly. Check the connector.
NOTE: If problems persist, contact Autel's technical support or your local selling agent.
11. Specifications
11.1 MaxiCOM MK808BT Pro Tablet
| Item | Description |
|---|---|
| Recommended Use | Indoor |
| Operating System | Android™ 11 |
| Processor | Cortex-A55 quad-core processor (1.8GHz) |
| Memory | 4GB RAM & 64GB On-board Memory |
| Display | 7-inch LCD capacitive touchscreen with 1024x600 resolution |
| Connectivity | Mini USB 2.0, USB2.0, Wi-Fi (2.4 & 5GHz), HDMI Type A, Micro SD card slot (supports up to 64GB), Bluetooth |
| Sensors | Light sensor for brightness auto changing |
| Audio Input/Output | Input: N/A, Output: buzzer |
| Battery | 3.7 V/5000 mAh lithium-polymer battery |
| Battery Charging Input | 5 V/3 A |
| Tested Battery Life | Around 6.5 hours of continuous use |
| Power Consumption | Approx. 600 mA (LCD on with default brightness, Wi-Fi on) @3.7 V |
| Operating Temp. | 0 to 50 °C (32 to 122 °F) |
| Storage Temp. | -10 to 60 °C (14 to 140 °F) |
| Operating Humidity | 5% to 95% non-condensing |
| Dimensions (W x H x D) | 270.8 mm (10.0") x 176.0 mm (6.9") x 36.0 mm (1.4") |
| Item Weight | 2.65kg |
| Material | Plastic + ABS |
| External Testing Certification | CE |
11.2 MaxiVCI Mini
| Item | Description |
|---|---|
| Communications | BT V.2.1 + EDR, Mini USB 2.0 |
| Wireless Frequency | 2.4 GHz |
| Input Voltage Range | 12 V DC to 24 V DC |
| Supply Current | 150 mA @ 12 V DC |
| Operating Temp. | 0 to 50 °C (32 to 122 °F) |
| Storage Temp. | -10 to 60 °C (14 to 140 °F) |
| Dimensions (L x W x H) | 47 mm (1.7") x 23 mm (0.9") x 51 mm (2.0") |
| Weight | 33.1 g (0.07 lbs.) |
11.3 MaxiBAS BT506 Battery Tester
| Item | Description |
|---|---|
| Connectivity | USB 2.0, Type C, Bluetooth 4.2 |
| Input Voltage | 5 V DC |
| Working Current | < 150 mA at 12 V DC |
| Internal Battery | 3.7 V/800 mAh Lithium-ion Polymer battery |
| CCA Range | 100 to 2000 A |
| Voltage Range | 1.5 to 16 V |
| Working Temp. | -10 °C to 50 °C (14 °F to 122 °F) |
| Storage Temp. | -20 °C to 60 °C (-4 °F to 140 °F) |
| Dimension (L x W x H) | 107 mm (4.21") x 75 mm (2.95") x 26 mm (1.02") (clamp cable not included) |
| Weight | 320 g (0.7 lbs.) |
12. User Tips
Based on general best practices for diagnostic tools:
- Keep Software Updated: Regularly check for and install software updates to ensure compatibility with the latest vehicle models and access new features.
- Stable Connection: Always ensure a stable Bluetooth or USB connection between the tablet and VCI Mini during diagnostics to prevent data loss or ECU issues.
- Battery Management: Keep the tablet and any connected battery testers sufficiently charged before starting diagnostic sessions. Avoid charging in extreme temperatures.
- Data Logging: Utilize the data logging feature when encountering complex issues. This allows Autel support to assist more effectively.
- Vehicle Compatibility: While the tool supports a wide range of vehicles, always verify compatibility for specific functions with your vehicle's make, model, and year.
Note: No specific buyer reviews or Q&A content were provided for this product, so these tips are based on general best practices for diagnostic tools.
13. Warranty and Support
13.1 Limited One Year Warranty
Autel Intelligent Technology Corp., Ltd. warrants to the original retail purchaser that this MaxiCOM diagnostics device, if proven defective in material or workmanship under normal usage within twelve (12) months from purchase, will be repaired or replaced (with new or rebuilt parts) at Autel's option, without charge for parts or labor directly related to the defect(s).
NOTE: If the warranty period is inconsistent with local laws and regulations, please comply with the relevant local laws and regulations.
The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the device. This warranty does not apply to products subjected to abnormal use, neglect, unauthorized alteration, improper installation, or damage from external causes like fire, dirt, battery leakage, or improper electrical source usage.
IMPORTANT: All contents of the product may be deleted during repair. Create a backup copy of your product's contents before delivering it for warranty service.
13.2 Service Procedures
This section provides information on technical support and repair service.
13.2.1 Technical Support
If you have any questions or problems, please contact Autel:
Autel China Headquarters:
- Phone: +86 (0755) 8614-7779 (Monday-Friday, 9AM-6PM Beijing Time)
- Email: support@autel.com
- Address: Floor 2, Caihong Keji Building, 36 Hi-tech North Six Road, Songpingshan Community, Xili Sub-district, Nanshan District, Shenzhen City, China
- Web: www.autel.com
Autel North America:
- Phone: 1-855-288-3587 (Monday-Friday, 9AM-6PM Eastern Time)
- Email: ussupport@autel.com
- Address: 36 Harbor Park Drive, Port Washington, New York, USA 11050
- Web: www.autel.com/us
Autel Europe:
- Phone: +49(0)89 540299608 (Monday-Friday, 9AM-6PM Berlin Time)
- Email: support.eu@autel.com
- Address: Landsberger Str. 408, 81241 München, Germany
- Web: www.autel.eu
Autel APAC (Japan):
- Phone: +81-045-548-6282
- Email: support.jp@autel.com
- Address: 6th Floor, Ari-nadoribiru 3-7-7, Shinyokohama, Kohoku-ku, Yokohama-shi, Kanagawa-ken, 222-0033 Japan
- Web: www.autel.com/jp
Autel APAC (Australia):
- Email: aussupport@autel.com
- Address: Unit 5, 25 Veronica Street, Capalaba
Autel IMEA:
- Phone: +971 585 002709 (in UAE)
- Email: imea-support@autel.com
- Address: 906-17, Preatoni Tower (Cluster L), Jumeirah Lakes Tower, DMCC, Dubai, UAE
- Web: www.autel.com
Autel Latin America (Mexico):
- Phone: +52 33 1001 7880 (Spanish in Mexico)
- Email: latsupport@autel.com
- Address: Avenida Americas 1905, 6B, Colonia Aldrete, Guadalajara, Jalisco, Mexico
Autel Latin America (Brazil):
- Email: brsupport@autel.com
- Address: Avenida José de Souza Campos n° 900, sala 32 Nova Campinas
13.2.2 Repair Service
If repair is necessary, contact Autel and download the repair service form from www.autel.com. Include contact name, return address, telephone number, product name, complete description of the problem, proof-of-purchase for warranty repairs, and preferred payment method for non-warranty repairs.
13.2.3 Other Services
Optional accessories can be purchased from Autel's authorized tool suppliers or local distributors. Include contact information, product/part name, item description, and purchase quantity in your order.
14. Compliance Information
14.1 FCC Compliance
FCC ID: WQ8-MX808S-TS2152
This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference. If interference occurs, try reorienting/relocating the receiving antenna, increasing separation, or connecting equipment to a different circuit.
14.2 SAR (Specific Absorption Rate)
The radiated output power of this device is below FCC radio frequency exposure limits. The device should be used to minimize human contact. The SAR limit set by the FCC is 1.6 W/Kg. To avoid exceeding FCC radio frequency exposure limits, human proximity to the antenna should be minimized.
14.3 RF WARNING STATEMENT
The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.
14.4 RoHS COMPLIANCE
This device is declared to be in compliance with the European RoHS Directive 2011/65/EU.
14.5 CE COMPLIANCE
This product conforms to the essential requirements of the Radio Equipment Directive 2014/53/EU and carries the CE mark.
14.6 NBTC COMPLIANCE
“เครื่องวิทยุคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกำหนดทางเทคนิคของกสทช." (This telecommunication equipment conforms to the technical standards or requirements of NBTC.)
“เครื่องวิทยุคมนาคมนี้มีอัตราการดูดกลืนพลังงานจำเพาะ (Specific Absorption Rate - SAR) อันเนื่องมาจากเครื่องวิทยุคมนาคมเท่ากับ0.350W/kgซึ่งสอดคล้องตามมาตรฐานความปลอดภัยต่อสุขภาพของมนุษย์จากการใช้เครื่องวิทยุคมนาคมที่คณะกรรมการกิจการโทรคมนาคมแห่งชาติประกาศกำหนด.” (This radiocommunication equipment has the specific absorption rate (SAR) of 0.350W/kg as related to the equipment, which is in compliance with the Safety Standard for the Use of Radiocommunication Equipment on Human Health announced by the National Telecommunications Commission.)

Figure 14-1: NBTC Compliance Information