SmallRig S70-C2

Contents

SmallRig S70-C2 Wireless Microphone User Manual

Model: 5717

Important Safety Information

Thank you for choosing SmallRig products. Please read this manual carefully before using the product to ensure safe and correct operation.

  • Always read all warning prompts and follow all instructions provided in this user manual.
  • The battery's state of charge (SoC) is ≤30% of the rated design capacity at the time of leaving the factory.
  • This product contains a built-in, non-removable lithium battery. Unauthorized disassembly is strictly prohibited. Do not attempt to disassemble external lithium batteries.
  • For prolonged storage without use, it is recommended to charge and discharge the battery once every 6 months. Restore approximately 60% of the charged capacity to extend battery lifespan.
  • Do not dispose of the product or its battery carelessly, as it contains harmful substances. Recycle damaged or unused products in accordance with waste management regulations.
  • Children should use this product only under adult supervision.
  • Keep new and used batteries out of reach of children.
  • Do not disassemble the product or the battery. If you suspect any issues with the product, please contact the purchase platform for after-sales assistance.

Product Overview

What's in the Box (S70-C2, Model 5717)

The SmallRig S70-C2 package includes the following components:

Contents of the SmallRig S70-C2 package, showing charging case, two transmitters, one receiver for Type-C, one receiver for camera, two windscreens, cables, and carry case.

Components:

  • Transmitter (TX) × 2
  • Receiver for Camera (RX) × 1
  • Receiver for Type-C (RX) × 1
  • Windscreen × 2
  • USB-C Charging Cable × 1
  • 3.5mm TRS Audio Cable × 1
  • Carry Case × 1
  • Charging Case × 1

Component Identification

Familiarize yourself with the various parts of your SmallRig S70-C2 Wireless Microphone system.

Diagram of the SmallRig S70 charging case with two transmitters (TX1, TX2) and two receivers (RX 3.5, RX-C/L) labeled.

Charging Case and Transmitters

  1. Charging Case: Provides charging for the transmitter and receiver, and storage for the product.
  2. Battery Indicator Light: Equipped with 4 white LED beads.
    • 1 LED bead steady on: 20% remaining battery level
    • 2 LED beads steady on: 50% remaining battery level
    • 3 LED beads steady on: 75% remaining battery level
    • 4 LED beads steady on: 100% remaining battery level
    • Fully charged: 4 LED beads steady on
    • Low battery: 1 LED bead fast flashing
    • Charging in progress: 4 LED beads in cyclic running-light flashing
  3. Transmitter (TX): Built-in omnidirectional microphone.
  4. Charging Contacts: The charging case charges the transmitter via these contacts.
  5. Titanium Metal Clip: Can clip the microphone to clothes.
  6. LED Status Indicator (TX):
    • Blue fast flashing: Pairing mode
    • Blue slow flashing: Reconnecting mode
    • Blue steady on: Connection successful
    • Green steady on: Noise reduction enabled (during operation)
    • Green steady on: Fully charged (during charging)
    • Red steady on: Mute mode (during operation)
    • Red slow flashing: Charging in progress
    • Red fast flashing: Low battery level
  7. Multi-Function Button (MTB) for TX:
    • Long press for 3 seconds: Power on/off (blue slow flashing)
    • Long press for 6 seconds (power-off state): Enter pairing mode (blue fast flashing)
    • Single press: Enable/disable noise reduction mode (green on/off)
    • Double press: Enable/disable mute mode (red on/off)
Diagram of the SmallRig S70 receiver with numbered parts including USB-C plug, LED indicators, and audio ports.

Receiver (RX)

  1. USB-C Plug: Compatible with mobile phones and tablets with USB-C ports.
  2. LED Status Indicators (RX): Two left/right indicators show status of TX1 / TX2 respectively.
    • Blue slow flashing: Reconnecting mode
    • Blue fast flashing: Pairing mode
    • Blue steady on: Connection successful
    • Green steady on: Noise reduction enabled
    • Red steady on: Mute mode
    • During gain adjustment, the three indicators show the gain levels: 1 red light (Gain Level 1), 2 red lights (Gain Level 2), 3 red lights (Gain Level 3)
  3. Recording Mode Toggle Switch: M: Mono Mode; S: Stereo Mode.
  4. USB-C Female Port: Can supply power to mobile phones by connecting a USB-C power source (supports "charge-while-use").
  5. Multi-Function Button (MTB) for RX:
    • Long press for 6 seconds: Enter pairing mode
    • Single press: Switch between 3 recording volume levels
  6. LED Status Indicators (RX): The one labeled "RX" is the RX status indicator.
    • Green steady on: Power-on state (in use)
    • Green steady on: Fully charged (during charging)
    • Green slow flashing: Charging in progress (during charging)
    • Green fast flashing: Low battery level (during charging)
    • Indicators 1 & 2 (TX status indicators): Blue slow flashing (reconnecting), Blue fast flashing (pairing), Blue steady on (connection successful), Red-blue alternating flashing (firmware updating)
  7. Multi-Function Button (MTB) for RX:
    • Power On/Off: Long press the RX MTB for 3 seconds (RX indicator blue slow flashing)
    • Pairing Mode: Long press the RX MTB for 6 seconds in power-off state (RX indicator blue fast flashing)
    • Noise Reduction Mode: Single press the RX MTB to enable/disable (Indicators 1 & 2 green on/off)
    • Mute Mode: Double press the RX MTB to enable/disable (Indicators 1 & 2 red on/off)
  8. Recording Mode Lever: M for Mono Mode / Ms for Safe Track Mode / S for Stereo Mode.
  9. Gain Knob: 5-level gain adjustment, ±5 dB per level.
  10. Charging Contacts: The charging case charges the transmitter via these contacts.
  11. USB-C Port: Charges the RX battery / Supports wired UAC interface.
  12. Cold Shoe Plate: Connects to the camera's cold shoe mount / hot shoe mount.
  13. 3.5 mm Audio Port: Connects to the camera via a 3.5 mm audio cable.

Setup

OTG Activation (for Android Devices)

When connecting the RX to your Android phone or tablet, if the indicator light does not illuminate, you may need to manually enable OTG (On-The-Go) in your device's settings. Search for "OTG" in your phone's settings and enable it. If issues persist, consult your mobile phone manufacturer or SmallRig customer service.Wearing Method

Ensure the microphone is worn correctly for optimal audio capture and discreet appearance.

Diagram showing correct and incorrect wearing methods for the microphone, and how to install the windshield muff.
  • Correct Wearing: The microphone pickup port should face outward.
  • Incorrect Wearing: Avoid wearing with the SmallRig logo facing outward, as this may obstruct the microphone.
  • Windshield Muff Installation: Slip the silicone cover of the windshield muff over the microphone head.
  • Important: The titanium wire should not be stretched beyond 40° to prevent irreversible damage to the product.

Operating Instructions

Connecting to Mobile Phones (USB-C)

  1. Remove the mobile phone receiver (RX-C) from the charging case and connect it to the USB-C charging port of your mobile phone or tablet.
  2. Take out a transmitter (TX) from the charging case. It will power on automatically and enter reconnecting mode (blue slow flashing). Wait 3 to 5 seconds for automatic reconnection.
  3. Once successfully reconnected, the blue lights on both the transmitter and receiver will remain steady on. You can now record audio via the transmitter.
  4. To charge your mobile phone while recording, connect a charging cable to the USB-C female port on the receiver. This supports "charge-while-use" functionality.
Diagram illustrating the connection of the SmallRig S70-C2 receiver to a mobile phone and the transmitter pairing process.

Connecting to Cameras

  1. Remove the camera receiver (RX 3.5) from the charging case. It will power on automatically. Connect it to your camera's cold shoe mount or hot shoe mount.
  2. Connect the camera receiver to your camera via the provided 3.5 mm TRS-to-TRS audio cable.
  3. Take out a transmitter (TX) from the charging case. It will power on automatically and enter reconnecting mode (blue slow flashing). Wait 3 to 5 seconds for automatic reconnection.
  4. Once successfully reconnected, the blue lights on both the transmitter and receiver will remain steady on. You can now record audio via the transmitter.
Diagram illustrating the connection of the SmallRig S70-C2 receiver to a camera's cold shoe mount and the transmitter pairing process.

Connecting to Computers

  1. Remove the camera receiver (RX 3.5) from the charging case. It will power on automatically. Connect it to your computer via a USB-C-to-USB-C cable.
  2. Take out a transmitter (TX) from the charging case. It will power on automatically and enter reconnecting mode (blue slow flashing). Wait 3 to 5 seconds for automatic reconnection.
  3. Once successfully reconnected, the blue lights on both the transmitter and receiver will remain steady on. You can now record audio via the transmitter.
Diagram illustrating the connection of the SmallRig S70-C2 receiver to a computer via a USB-C cable and the transmitter pairing process.

Maintenance

  • Battery Storage: If the battery is stored for a long period without use, it is recommended to charge and discharge it once every 6 months. Restore approximately 60% of the charged capacity to prolong its lifespan.
  • Cleaning: Use a soft, dry cloth to clean the device. Avoid using harsh chemicals or abrasive materials.
  • Disposal: Do not dispose of the product or its battery with household waste. Follow local regulations for electronic waste recycling.

Troubleshooting

  • Indicator Light Not On (Android RX): If the RX indicator light does not come on when plugged into your Android device, manually enable OTG (On-The-Go) in your phone's settings. Search for "OTG" in settings.
  • Interference Issues (FCC Statement): This equipment generates and uses radio frequency energy. If it causes harmful interference to radio or television reception, try the following:
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment to an outlet on a different circuit.
    • Consult the dealer or an experienced radio/TV technician.
  • Product or Battery Malfunction: Do not attempt to disassemble or repair the product or battery yourself. Contact the purchase platform for after-sales assistance if you suspect any issues.

Specifications

ParameterValue
Operating Power45.5mW
Standby Power Consumption38.5μW
Frequency Band2400 to 2483.5MHz
Frequency Response Range20Hz to 20kHz
Sample Rate / Bit Depth48kHz / 24bit
One-Click DSP Noise ReductionSupported / 3-level adjustment in APP
Charge-While-UseSupported
Camera Sync Power On/OffSupported / Disabled by default, enabled in APP
Auto Limiter (Anti-Popping)Supported / Enabled by default, disabled in APP
Battery Parameters (Charging Case)3.7V / 1,000mAh / 3.7Wh (for 5717)
Battery Parameters (Transmitter)3.87V / 85mAh / 0.32895Wh
Battery Parameters (Camera Receiver)3.87V / 110mAh / 0.426Wh
Charging Temperature0°C (32°F) to 45°C (113°F)
Operating Temperature-10°C (14°F) to 45°C (113°F)
Product Dimensions94.0 × 52.0 × 40.4mm / 3.7 × 2.0 × 1.6in
Product Weight136.0g / 4.8oz
Package Dimensions122.0 × 115.0 × 54.0mm / 4.8 × 4.5 × 2.1in
Package Weight199.0g / 7.0oz
Material(s)ABS + PC, Nitinol (Nickel-Titanium Alloy), Silicone

User Tips

  • Build Quality: Users frequently praise the robust construction and excellent value for money of SmallRig products.
  • Compatibility: The S70-C2 is designed for devices with USB-C ports. If your device uses a Lightning connector (e.g., some Apple iPhones/iPads), you will need a separate Lightning adapter, which is not included in this package.
  • Discreet Design: The ultra-slim, logo-free design of the transmitters allows for discreet placement, ensuring they remain out of sight during recording.

Warranty and Support

For detailed warranty information, technical support, or after-sales assistance, please contact the vendor or the SmallRig customer service directly through your purchase platform.

A comprehensive user manual in PDF format is available for download: SmallRig S70 Wireless Microphone User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.