1. Product Features
Thank you for choosing our company's products. This series of soldering stations is based on the most advanced modern control concept for temperature control, using microcomputer PID full-process control, with the characteristics of less failure, accurate temperature control, and fast temperature recovery.
- Dual-Station Closed-Loop Control: This dual-station soldering station uses a closed-loop sensing circuit to control the temperature, with the sensor and heating core integrated into one body.
- Dual Handle Compatibility: Supports simultaneous operation of two handles and is compatible with 210-type and 245-type handles, allowing users to switch between different scenarios.
- Efficient Switching Power Supply: The soldering station uses a switching power supply, offering high efficiency, energy saving, stable temperature, portability, multi-functionality, and fast response. This improves welding efficiency and quality and is suitable for various welding needs.
- Alarm System: Features a sound alarm and a fault code alarm prompt.
- Versatile Applications: Suitable for electronic component pin welding, industrial welding, production line welding operations, laboratory teaching, DIY projects, and use by a wide range of electronic enthusiasts.
2. Packing List
Please check the soldering station packaging to confirm that all listed items are correct.
| Item | Quantity |
|---|---|
| Double-station soldering station host | 1 unit |
| Soldering iron stand | 1 unit |
| Wire harness clamp | 2 units |
| Wire harness clamp hand screw (M5*12 specification) | 2 units |
| Soldering Station Handle | 2 units |
| Soldering Iron Tip | 2 units |
| Power cord | 1 unit |
| High temperature absorbent sponge | 1 piece |
| Banana head alligator clip ground wire | 1 unit |
| Manual | 1 copy |
| Warranty card | 1 piece |
| After-Sale Service Card | 1 piece |
3. Product Overview
Side Display

- FW-S2 Pro Max Host
- Soldering Iron Tip Storage Box
- Display Area
- Up/Down Button
- Memory Channel Button
- Setting Button
- Tin Dross Silicone Tray
- High Temperature Sponge
- Soldering Iron Tip Wiping Hole
- A Handle
- A Bracket
- B Handle
- B Bracket
- Harness Clip
Back Display

- A Handle Interface
- B Handle Interface
- Anti-counterfeit Label
- Power Label
- TYPE-C Firmware Upgrade Port
- Banana Socket Ground Wire Interface
- Power Cord Interface
- Fuse Sleeve
- Power Switch: 0 Off 1 On
4. Installation Steps
4.1 Heating Core Removal and Installation
It is best to turn off the power switch during operation.
Removing the Heating Core:
Put the heating core into the V-shaped card slot of the storage box, and pull up the handle to remove the heating core. (You can also use tweezers to gently pull it out).

Inserting the Heating Core:
Use your hands or tweezers to put the heating core into the handle, align the heating core head with the appropriate soldering iron tip hole in the storage box, and push it back hard to start working.

4.2 Banana Head Alligator Clip Ground Wire Installation
Align the banana head at one end of the banana socket of the host and insert the crocodile clip at the other end to clamp it to the metal connected to the ground.

5. Product Specifications
| Attribute | Value |
|---|---|
| Brand | FORWARD |
| Product Model | FW-S2 Pro Max |
| Heater Core Model | Type 210/Type 245 |
| Input Voltage | 85~260VAC |
| Output Voltage | 24VDC |
| Power Consumption | 400W |
| Temperature Range | 200°C~450°C |
| Constant Temperature Accuracy | ±3°C |
| Ground Resistance | <2mΩ |
| Product Weight | 1.34KG |
| Host Size | 264 x 156 x 130mm |
| Package Size | 305 x 245 x 155mm |
6. Operating Instructions
6.1 Tinning Steps (Initial Use)
When using the soldering station for the first time, the soldering iron tip needs to be tinned to extend its service life.
- Turn off the power switch and plug in the soldering iron handle.
- Plug in the power supply and ensure it is well grounded.
- Soak the high-temperature absorbent sponge with water and place it in the tin slag tray.
- Turn on the soldering station power switch. Adjust the temperature using the "Up/Down Button" on the panel to set it between 200~260°C.
- Wait for the heating to stabilize and the panel temperature to display a constant value before proceeding.
- Bring the solder wire close to the soldering iron tip to melt it and evenly apply it to the soldering part of the tip.
- The tinning steps for handle A and handle B are identical.
6.2 Basic Operation Instructions
Adjusting Temperature:
Click the "Up/Down Button" to increase or decrease the temperature by 1 degree. Long press the "Up/Down Button" to increase or decrease by 5 degrees.

Memory Channel:
Click the memory channel button to recall a preset temperature. To modify a memory channel parameter, adjust the desired temperature, then long press the corresponding memory channel button until the system beeps to save.

Menu Interface Function Description:
Long press the setting button to enter/exit the menu interface. Click the up/down button to switch between options, and click the setting button again to confirm a selection.

Work Mode:
The standard mode allows setting temperature, memory channels, and other normal operations. The curve mode (double-click setting button or select from menu) displays temperature and power conversion processes during work.

Temperature Unit Settings:
You can set the temperature unit to Celsius or Fahrenheit. Use the up/down buttons to switch and click the setting button to save and exit.

Temperature Compensation Settings:
Switch to the handle needing calibration (A or B) using the up/down button. Adjust the actual temperature using the up/down button, then click the setting button for automatic calibration. Repeat if necessary for multiple calibrations.

Sound Settings:
The system sound can be turned on or off using the up/down button. Click the setting button to save and exit.

Numerical Display Settings:
When unlocked, the temperature value fluctuates with the actual temperature. Switch between locked/unlocked using the up/down button and click the setting button to save and exit.

Delayed Sleep Settings:
You can set the delay time before the handle enters sleep mode. At 0 minutes, the handle will enter sleep immediately when placed back on the stand. The maximum delay can be set to 99.9 minutes. Adjust the up/down button to switch to the handle (A or B) for which you want to set the sleep delay. Click the setting button to enter, adjust the desired delay time, and click the setting button again to save and exit.

Restore Factory Settings:
Confirming to restore factory settings will erase personal parameters and revert to default settings. It is not recommended unless necessary.

7. Maintenance and Care
- Cleaning the Soldering Tip: If the soldering iron tip is dirty, wipe it clean on a high-temperature absorbent sponge or wipe it on the soldering iron hole.
- Temperature Adjustment: When the tip is covered with a layer of tin, it can be adjusted to the appropriate temperature for normal operation.
- Power Off: When you finish working, place the handle back on the soldering iron stand and turn off the power supply.
- Optimal Soldering Temperatures:
- For lead-containing soldering: 330-360°C
- For lead-free soldering: 340-380°C
- Solder Wire Selection: Use solder wire with a low melting point to effectively extend the service life of the soldering iron tip.
- Temperature Calibration: The soldering station is factory-calibrated. After a period of use, oxidation of the soldering iron tip may cause temperature deviation. If necessary, a temperature meter can be used for calibration. Refer to the "Interface explanation and Function Description" section for calibration methods.
8. Troubleshooting
- Low Temperature Alarm: The soldering iron tip is damaged. Replace the heating core.
- High Temperature Alarm: The sensor wire is abnormal, the heating core is open circuit, or the heating core is not installed properly.
- Heating Core Error: The internal part of the soldering iron tip is short-circuited. Replace the soldering iron tip.
- No Soldering Iron: The handle is not properly connected.
- No Power/Screen Off: No response when turning on the machine, the screen is not lit, and the heating core has no temperature. Check the power cord. If the power cord is normal, check whether the fuse is damaged or burned out. If damaged, replace the fuse with the same model.
Recommendation: Please use the original handle and heating core for a better welding experience.
9. Warranty and Support
9.1 Warranty Coverage
This product comes with a warranty card from the date of purchase (subject to the purchase receipt). The whole machine is under warranty for one year.
Fragile items not under warranty:
- Heating core
- Packaging accessories
- Anti-slip cover of handle
- High-temperature sponge
Human damage is not covered by warranty.
Unauthorized disassembly of the machine is not covered by warranty.
9.2 Technical Support
Technical guidance or after-sales support can be obtained through the QR code provided in the product's menu interface (refer to section 6.2, "Menu Interface Function Description").

10. Cautions
- Read the instructions carefully before use.
- Install the handle and soldering iron stand before powering on.
- Connect the alligator clip ground wire to avoid electric shock.
- Do not let foreign objects block the cooling fan inlet and outlet.
Safety Precautions (Burns or Fire Hazard):
- Do not touch the metal part near the soldering iron tip.
- Do not use near flammable objects.
- The soldering station becomes extremely hot and can cause dangerous accidents. Turn off the power when taking a break or leaving the workstation.
- When replacing soldering station parts or devices, turn off the power and wait until the soldering iron tip cools to ambient temperature before replacing.
Precautions to Prevent Damage and Maintain Safety:
- Never use the soldering iron for tasks other than soldering.
- Do not knock the soldering iron against the workbench to remove flux residue, as this can severely damage the heating element and handle.
- Do not modify the internal structure of the soldering station without authorization.
- Do not wet the soldering station or use it with wet hands.
- It is normal for the soldering iron head to produce smoke during use. Ensure the working environment has good ventilation.
- When using the soldering station, do not make any rash movements that could harm your body or damage the machine.
11. User Tips
- Tip Compatibility: This soldering station is compatible with both 210-type and 245-type soldering iron tips, offering flexibility for various tasks.
- Proper Grounding: Always ensure the soldering station is properly grounded using the provided banana head alligator clip ground wire to prevent electric shock and ensure stable operation.
- Regular Tip Maintenance: To prolong the life of your soldering iron tips, clean them regularly with the high-temperature absorbent sponge and re-tin them as needed.
- Temperature Settings: Use appropriate temperatures for your soldering tasks (e.g., 330-360°C for leaded solder, 340-380°C for lead-free solder) to achieve optimal results and prevent tip damage.