BAOFENG K5 PLUS

Contents

Baofeng K5 Plus 10W Handheld Walkie Talkie User Manual

Model: K5 PLUS

1. Safety Information and Warnings

Please read this manual carefully before using the Baofeng K5 Plus radio to ensure safe and efficient operation. Failure to comply with these instructions may result in property loss, bodily injury, or even death.

1.1 General Operating Prohibitions

  • Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Avoid operating near blasting areas or medical/electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate in areas where wireless communication equipment is prohibited.

1.2 Important Tips for Use

  • Use only authorized accessories.
  • Keep the product at least 2.5 cm away from your body during transmission.
  • Avoid prolonged reception at high volume.
  • Do not place the product in air bag deployment areas in vehicles.
  • Keep out of reach of children and pets.
  • Operate within the specified temperature range.
  • Allow for cooling if the product accumulates heat during continuous transmission.
  • Handle the product with care; do not disassemble, modify, or repair without authorization.

1.3 Battery Precautions

  • Do not charge or replace the battery in flammable/explosive environments.
  • Do not charge a wet battery; dry it with a soft, clean cloth first.
  • Avoid charging deformed, leaking, or overheated batteries.
  • Use only authorized chargers.
  • Do not charge in locations with strong radiation.
  • Avoid overcharging to prolong battery life.
  • Do not short-circuit battery terminals, throw into fire, or expose to direct sunlight/heat sources.
  • Do not squeeze, penetrate, or remove the battery housing.
  • Damaged batteries must not be transported.
  • When transporting multiple batteries, separate them from metal parts to avoid short circuits.
  • If the radio is attached to the battery during transport, ensure it is switched off and secured against accidental activation.

1.4 Regulatory Compliance

EU Regulatory Conformance: This product complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. Operation in Transmit mode requires a valid Amateur Radio License in Europe.

FCC Part 15 Compliance: This device complies with Part 15 of the FCC rules. Operation is subject to not causing harmful interference and accepting received interference. Unauthorized changes or modifications may void user authority to operate the equipment.

IC Compliance: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to not causing interference and accepting received interference. Unauthorized changes or modifications may void user authority to operate the equipment.

RF Exposure Warning: Proper operation is crucial for safe use. Do not use with a damaged antenna. For hand-held operation, maintain a 1-inch (2.5 cm) spacing from the front of the radio to the user's face. For body-worn operation, use only supplied belt-clip and manufacturer-approved accessories to comply with RF exposure guidelines.

2. Product Overview

The Baofeng K5 Plus is a 10W handheld walkie talkie featuring multi-band reception and transmission capabilities, a color large screen, and wireless frequency copy functionality.

2.1 Main Features

  • Frequency Range: FM radio 76-108 MHz (RX), AM aviation band 108-136MHz (RX), VHF1: 136-174MHz (RX&TX), VHF2: 220-260MHz (RX&TX), UHF1: 400-520MHz (RX&TX), UHF2: 350-390MHz (RX).
  • Display: 1.77" TFT large screen, full keyboard, fully open menu operation.
  • Channels: Up to 999 memory channels.
  • Power: 10W output power (5w-10w range).
  • Charging: Support USB (Type-C) charging and base charger.
  • Special Functions: One-click copy frequency, wireless copy frequency, frequency hopping, scramble functions, DTMF encoder and manual dial, VOX (voice activated transmit), alarm function, LED flashlight, Roger Beep, NOAA weather reception (US and Canada).
  • Scanning: Channel scan, frequency scan, CTCSS/DCS scanning with TO, CO, and SE recovery methods.
  • Other: Dual watch / Dual reception, high/low power selection, stopwatch, keypad lock, battery save function, busy channel lock out, 10 levels of Squelch adjustment, 2-pin Kenwood accessory port.

2.2 Package Contents

Upon unpacking, please verify that all items are present. If any item is missing or damaged, contact your dealer.

  • 1 x Baofeng K5 Plus Radio
  • 1 x Antenna
  • 1 x Li-ion Battery Pack
  • 1 x Fast Desktop Charger
  • 1 x Belt Clip
  • 1 x USB Type-C Cable (for direct charging)
  • 1 x User Manual (PDF)
Baofeng K5 Plus package contents

Image: Standard package contents of the Baofeng K5 Plus radio.

3. Setup and Installation

3.1 Radio Components Overview

Multiple views of the Baofeng K5 Plus radio

Image: Various views of the Baofeng K5 Plus radio, showing its design and key external features.

Detailed view of Baofeng K5 Plus showing Power/Volume, PTT Key, and Type-C Charging

Image: Detailed view highlighting the Power/Volume knob, PTT (Push-to-Talk) key, and Type-C charging port.

The radio features a Power/Volume knob, PTT key, SK1 (Broadcast FM and Alarm) key, SK2 (Flashlight and Monitor) key, V/M mode key, A/B select key, MENU key, BAND key, Numeric keypad, Star (*) key, Pound (#) key, EXIT key, Antenna jack, LED flashlight, Color LCD, Accessory jack, Speaker and microphone, Type-C charging port, and Battery release latch.

3.2 Battery Charging

The Li-ion battery pack is not charged at the factory and must be charged before first use. For optimal performance, fully charge and discharge the battery two or three times.

Using the Desktop Charger:

  1. Plug the AC adapter into an outlet and connect it to the DC jack on the back of the charger. The indicator will blink orange.
  2. Place the battery (or radio with battery) into the charger, ensuring good contact with the charging terminals. The indicator will turn red.
  3. Charging takes approximately 2-5 hours. The indicator turns green when fully charged.
  4. If charging the radio with the battery, ensure the radio is OFF for correct charging status indication.

Using the Type-C USB Charger:

The Type-C USB port allows convenient charging of the Li-ion battery pack directly.

  1. Ensure the radio is turned OFF.
  2. Plug the Type-C USB cable into the charging port on your battery and connect the other end to a wall power outlet.
  3. An empty battery will fully charge in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging progress.

Note:

  • It is recommended to power OFF the radio while charging.
  • For optimal battery life, remove the radio from the charger within 6 hours.
  • Store the battery with approximately 80% charge in a low-temperature, dry environment, away from direct sunlight.
Baofeng K5 Plus large battery capacity and Type-C charging

Image: Highlighting the large battery capacity and convenient Type-C charging feature.

3.3 Installing the Antenna

  1. Screw the antenna into the connector on top of the transceiver by holding the antenna at its base.
  2. Turn clockwise until secure.
  3. To remove, turn counter-clockwise.

3.4 Installing the Belt Clip

  1. Locate the two parallel screws above the battery on the back of the radio.
  2. Remove these screws.
  3. Align the belt clip with the screw holes and thread the screws back in, tightening them until secure.
  4. To remove, unscrew counter-clockwise.

3.5 Installing the Battery Pack

  1. Ensure the radio is turned OFF by rotating the power/volume knob counter-clockwise.
  2. Align the battery pack parallel with the radio body, with its lower edge about 1-2cm below the radio's edge.
  3. Slide the battery upward along the guide-rails until it clicks into place.
  4. To remove, press the battery release button above the battery pack and slide the battery downward.

3.6 Installing Additional Speaker/Microphone (Optional)

  1. Pry open the rubber MIC-Headset jack cover on the side of the radio.
  2. Insert the Speaker/Microphone plug into the double jack.

4. Operation

4.1 Power On/Off

  • To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will emit a double beep, display a message or flash the LCD, and then show a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • To Turn Off: Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click".

4.2 Adjusting the Volume

  • To Increase: Rotate the Volume/Power knob clockwise.
  • To Decrease: Rotate the Volume/Power knob counter-clockwise.
  • Use the monitor function (press and hold SK2) to open the squelch and adjust volume to the unsquelched static for easier setting.

4.3 Main Band/Sub Band Select (A/B Key)

In standby mode, press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes the active listening and transmit frequency/channel. To save frequencies to channel memory, you must be on the A display.

4.4 VFO/Channel Switch (V/M Key)

Press the [V/M] key to switch between VFO (Frequency) mode and MR (Channel) mode.

  • In Channel (MR) mode, the channel number is displayed.
  • In Frequency (VFO) mode, 'VFO' is displayed.

4.5 Frequency (VFO) Mode

In VFO mode, you can navigate frequencies using the ▲/▼ keys or by directly inputting frequencies with the numeric keypad. This mode is useful for experimentation and programming channels into memory.

Example: Entering 436.61250 MHz on display A

  1. In standby mode, press [V/M] key to switch to VFO mode.
  2. Enter [4][3][6][6][1][2][5][0] on the numeric keypad.

WARNING: Transmitting on unauthorized frequencies is illegal. Always comply with local regulations.

4.6 Channel (MR) Mode and Channel Selection

MR mode is for selecting preprogrammed channels. You can navigate channels using the ▲/▼ keys or by directly inputting the channel number (e.g., [0][1][2] for channel 12).

4.7 Making a Call

  • Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone. The red LED indicates transmission.
  • Frequency Mode Call: Switch to VFO mode, input the desired frequency, then hold down the [PTT] key to transmit.
  • Receiving a Call: Release the [PTT] key. The green LED indicates reception.
  • For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

4.8 Using the Flashlight (SK2 Key)

  • Press [SK2] once for continuous light.
  • Press [SK2] again for strobe (emergency signal).
  • Press [SK2] a third time to turn off.

4.9 Emergency Alert (SK1 Key)

To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] again to exit. Use only in actual emergencies.

4.10 FM Radio (SK1 Key, BAND Key)

The radio can receive FM broadcasts from 65-108MHz.

  1. In frequency or channel mode, press [SK1] to turn on the radio.
  2. Select the desired frequency using ▲/▼ keys or input directly. Press [#] to auto-search.
  3. Press [SK1] to exit FM radio.
  4. When listening to broadcast FM, the [BAND] key switches between 65-75 MHz and 76-108 MHz bands.

4.11 Monitor Function (SK2 Key)

In standby, press and hold the [SK2] key to enter Monitor mode. This allows you to hear weak signals or signals with matched carriers but no signaling. Release [SK2] to exit.

4.12 Keypad Lock (* Key)

To enable/disable the keypad lock, press and hold the [*] key for about two seconds. This locks all keys except the three side keys. The radio can also be set to automatically lock after a set period via the menu.

4.13 Frequency Reversal (* Key)

A short momentary press of the [*] key enables the reverse function, swapping transmit and receive frequencies. An 'R' will appear on the LCD.

4.14 TX Repeaters Tone (PTT + SK2)

Press [PTT] + [SK2] to send a 1750Hz repeater tone, useful for accessing repeaters. This works even if the keypad is locked.

4.15 One-Touch Frequency Search (BAND Key)

Press and hold the [BAND] key. The radio will display "SEARCH SEARCH..." and search for active frequencies. If a signal is found, the frequency and any CTCSS/DCS values will be displayed. Press [MENU] to save the found frequency to a channel. During search, press [#] to switch between UHF/VHF bands.

4.16 Weather Radio/Scan Weather Channel (0 Key)

The radio supports NOAA Weather Radio reception and scanning.

  1. To turn on NOAA Weather Scan, press and hold the [0] key for 3 seconds. The radio will enter Weather band mode.
  2. Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 NOAA channels. Press [#] again to stop.
  3. After stopping, you can manually select channels with ▲/▼ keys.
  4. To exit, press [EXIT] or [PTT].

Weather channels (Wx 1-10) are receive-only for NOAA and Canadian weather broadcasts.

4.17 Working the Menu System

The menu system allows customization of various radio settings. Many menu items will not take effect if the radio is in Memory (MR) mode.

Basic Use:

  1. Press [MENU] to enter the menu.
  2. Use ▲/▼ keys to navigate.
  3. Press [MENU] again to select an item.
  4. Use ▲/▼ keys to select a parameter.
  5. Press [MENU] to confirm and save, or [EXIT] to cancel.
  6. Press [EXIT] at any time to exit the menu.

Using Shortcuts:

Each menu item has a numerical value for direct access.

  1. Press [MENU].
  2. Enter the menu item number using the numeric keypad.
  3. Press [MENU] to enter the item.
  4. Enter the parameter's numerical shortcut or use ▲/▼ keys.
  5. Press [MENU] to confirm, or [EXIT] to cancel.

4.18 Scanning

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans according to the set frequency step. In MR mode, it scans your programmed channels. To enable, press and hold [#] for about two seconds. Press and hold [#] again to exit.

Scanning Modes:

  • Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes after the signal disappears.
  • Search Operation (SE): Scanner stops on a signal and waits for manual resume.

Frequency Scanning:

In VFO mode, press and hold [#] for >2 seconds. Change direction with ▲/▼. Press [#] to stop.

Channel Scanning:

In MR mode, press and hold [#] for >2 seconds. Change direction with ▲/▼. Press [#] to stop.

CTCSS/DCS Scanning:

Access via MENU [1][4] for CTCSS or MENU [1][5] for DCS. Press [MENU] to start scanning. Not available in Channel mode.

4.19 Manual Programming (Channels Memory)

The radio has 999 memory channels to store frequencies, transmit power, signaling, bandwidth, and alphanumeric identifiers.

Example: Programming a Channel Repeater Offset with CTCSS Tone

RX = 432.55000 MHz, TX = 437.55000 MHz (Offset +5), TX CTCSS tone 123.0

  1. Press [EXIT] to switch between menus.
  2. Press [V/M] to set radio to VFO mode.
  3. [MENU] [3][1] [MENU] [1][0] [MENU] [EXIT] (Deletes prior data in channel 10)
  4. [MENU] [1][2] [MENU] 123.0 [MENU] [EXIT] (Selects desired TX encode tone)
  5. Enter RX frequency (e.g., 43255000).
  6. [MENU] [3][0] [MENU] [1][0] [MENU] [EXIT] (Enters desired channel 10, RX added)
  7. Enter TX frequency (e.g., 43755000).
  8. [MENU] [3][0] [MENU] [1][0] [MENU] [EXIT] (Enters same channel 10, TX added)
  9. Press [V/M] to return to MR mode.

4.20 VOX (Voice Operated Transmit)

Enables hands-free communication. Access via MENU + 7. Select VOX level (1-10, 1 least sensitive, 10 most sensitive) or turn OFF. Not available in Scan or FM Radio mode.

4.21 Dual Watch

Allows monitoring two channels simultaneously. Access via MENU + 7. Use ▲/▼ keys to enable or disable.

4.22 Stopwatch Timer

Access via MENU + 44. Press [MENU] to start/restart counting. Press [EXIT] to stop and exit.

4.23 Scrambler

Voice inversion function for private communication. Access via MENU + 45. Select scramble mode (MODE1-MODE3). "SCR" icon appears when enabled.

4.24 DTMF (Dual-Tone Multi-Frequency)

Used for automation and remote control. To send DTMF codes, press the corresponding number keys while holding down the PTT key. The A, B, C, D codes are located on the [MENU], ▲, ▼, and [EXIT] keys respectively.

4.25 Customization Options

  • Display Backlight (ABR) - MENU 7: Set delay time for LCD backlight.
  • Beep PROMPT (BEEP) - MENU 8: Enable/disable key press beep tone.
  • Voice Function (VOICE) - MENU 17: Enable/disable voice confirmation of key presses.
  • Language (LANGUAGE) - MENU 18: Select menu language (English/Chinese).
  • Working Mode (MDF-A) - MENU 24: Select display mode (Frequency, Channel, Channel Name).
  • Roger Beep (ROGER) - MENU 36: Enable/disable end-of-transmission tone.
  • Power On Message (POWER ON MSG) - MENU 40: Customize welcome message (Voltage, Message, Logo, Model Name).
  • Power On Password (POWER ON PWD) - MENU 43: Enable/disable password protection on power-on.
  • Reset (RESET) - MENU 42: Reset VFO settings or ALL settings to factory defaults.

5. Maintenance

Your Baofeng K5 Plus radio is a precision electronic device and should be handled with care.

  • Cleaning: Regularly wipe the charging connector with a clean, dry cloth to prevent dust accumulation.
  • Storage: Do not store the radio in direct sunlight, hot areas, dusty/dirty environments, or damp conditions.
  • Battery Care: Charge the battery within the recommended temperature range (5°C to 40°C). Do not dispose of batteries in fire.
  • Repairs: Do not attempt to open or repair the radio yourself. Unauthorized opening will void the warranty. The radio's precision mechanics and electronics require specialized equipment and experience for realignment or repair.
  • Anomalies: If the radio emits a peculiar smell or smoke, immediately shut off power and remove the charger/battery.

6. Troubleshooting Guide

Phenomenon Possible Cause Solution
Radio does not turn on.
  • Battery installed improperly.
  • Battery power is low/depleted.
  • Poor battery contact (dirty/damaged).
  • Remove and reattach battery.
  • Recharge or replace battery.
  • Clean battery contacts or replace battery.
Weak or intermittent voice during reception.
  • Battery voltage low.
  • Volume level low.
  • Antenna loose or improperly installed.
  • Speaker blocked.
  • Recharge or replace battery.
  • Increase volume.
  • Turn off radio, remove and reattach antenna.
  • Clean speaker surface.
Cannot communicate with other group members.
  • Inconsistent frequency or signaling type.
  • Too far from other members.
  • Verify TX/RX frequency and signaling type.
  • Move closer to other members.
Hears unknown voices or noise.
  • Interrupted by radios using same frequency.
  • Radio in analog mode with no signaling.
  • Change frequency or adjust squelch level.
  • Request dealer to set signaling for current channel.
Unable to hear due to too much noise/hiss.
  • Unfavorable position (blocked by buildings/underground).
  • External electromagnetic interference.
  • Move to open, flat area; restart radio.
  • Stay away from interfering equipment.
Radio keeps transmitting.
  • VOX turned on.
  • Headset not installed correctly.
  • Turn off VOX function.
  • Check headset installation.

If these solutions do not resolve your issues, please contact your dealer for technical support.

7. Technical Specifications

Feature Specification
Frequency Range
  • FM: 65-108MHz (Rx)
  • AM: 108-136MHz (Rx)
  • VHF1: 136-174MHz (Rx&Tx)
  • VHF2: 220-260MHz (Rx&Tx)
  • UHF1: 400-520MHz (Rx&Tx)
  • UHF2: 350-390MHz (Rx)
Output Power 5W-10W
Channel Spacing 25.0KHz (Wide) / 12.5KHz (Narrow)
Memory Channels 999 Groups
Operation Voltage DC 7.4 V ±10%
Transmission Current ≤2800mA
Receive Sensitivity 0.25μV (12dB SINAD)
Rated Audio Power Output 1W @16 ohms
Receive Current ≤380mA
Connection for Accessories 2 pin Kenwood jack
Antenna Impedance 50 Ohm
Dimensions 125*65*40mm (not including antenna)
Material Plastic
Waterproof / Water-Resistant No
Battery Included Yes
Certification CE

Note: All specifications may be modified without prior notice or liability.

8. Warranty and Support

This product is designed for durability and performance. For any issues not covered in the troubleshooting guide, please contact your authorized dealer for support.

Unauthorized opening or modification of the transceiver will void the warranty. Always ensure compliance with local regulations regarding radio operation.

For a complete and detailed manual, please refer to the official PDF document: Baofeng K5 Plus User Manual (PDF)

9. User Tips

  • Pre-programmed Frequencies: If you acquire a radio that has been previously used, it may have frequencies saved in its memory. Always verify these frequencies against your authorized usage to ensure compliance.
  • Battery Life: To maximize battery life, avoid overcharging and store the battery at approximately 80% charge if not used for extended periods.
  • Programming: When programming new frequencies, it is recommended to first read the factory software data, then rewrite with your desired frequencies to avoid errors.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.