IKSLED PIR26L

Contents

PIR26L PIR Motion Sensor Switch User Manual

Model: PIR26L

1. Product Introduction

Front and back view of two PIR26L motion sensor switches

Figure 1: PIR26L Motion Sensor Switch. This image shows the front (dome) and back (adjustment switches) of two PIR26L sensors.

The PIR26L is an adjustable PIR (Passive Infrared) motion sensor switch, specifically designed for LED lighting fixtures. It automatically controls the on/off of lights by detecting human infrared radiation, making it ideal for automatic lighting in homes, corridors, warehouses, and other suitable environments.

2. Specifications

FeatureDetail
Model NumberPIR26L
Brand NameIKSLED
Power Load≤40W
Operating Voltage5V / 12V / 24V DC
Installation HeightRecommended 3.5m
Waterproof RatingIP22
Adjustable Delay Time3 seconds, 40 seconds, 4 minutes
Detection Range4-6 meters
Detection Angle120°
Compatible LightsLED bulbs, ceiling lamps, panel lights, floodlights, etc.
Recommended Mounting Hole26mm
MaterialPlastic
Warranty1 Year
CertificationsSAA, RoHS, LVD, EMC, CE, CCC
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
High-concerned chemicalNone
Product DimensionsDiameter 35mm, Length 35mm, Threaded Section Length 25mm

3. Setup and Installation

3.1. Wiring Instructions

This product features an integrated input/output design. It is crucial to distinguish between positive and negative poles during wiring to prevent damage.

  • Input Terminals: Connect to the DC power supply (5V/12V/24V).
    • Input positive (+)
    • Input negative (-)
  • Output Terminals: Connect to the LED light fixture.
    • Output positive (+)
    • Output negative (-)

Important: Disconnect the power supply before wiring to avoid electric shock. Do not reverse the positive and negative poles, as this may cause product damage.

Wiring diagram for PIR26L motion sensor switch

Figure 2: Wiring Diagram. This diagram illustrates the correct connection of input (power supply) and output (LED light fixture) terminals, clearly marking positive and negative poles.

3.2. Installation Dimensions and Precautions

  • Product Dimensions: Diameter 35mm, length 35mm, with a threaded section length of 25mm.
  • Mounting Hole: A 26mm diameter mounting hole is recommended for installation.
  • Installation Height: It is recommended to install the sensor at a height of 3.5 meters for optimal detection performance.
  • Installation Location: Avoid areas with direct sunlight, strong winds, or rapid temperature changes, as these conditions can affect the sensor's detection sensitivity and performance.
PIR26L sensor dimensions being measured by a digital caliper

Figure 3: Sensor Dimensions. The image shows the sensor's diameter being measured as 25.30mm, along with the adjustment switches for illumination and delay time.

Exploded view of PIR26L sensor showing the main body and retaining nut

Figure 4: Sensor Components. This image displays the main sensor body and its retaining nut, illustrating how it can be mounted.

3.3. Installation Demonstration

Video 1: Installation and Function Demonstration. This video illustrates the wiring process of the PIR26L sensor to a power supply and an LED strip, followed by a demonstration of its motion detection capabilities and how it activates the light.

4. Operating Instructions (Function Adjustment)

The PIR26L sensor features adjustable settings for both illumination sensitivity and light-on delay time. These settings can be configured using the switches located on the sensor body.

Close-up of PIR26L sensor adjustment switches

Figure 5: Adjustment Switches. A close-up view of the sensor's switches for setting illumination level (Deepdark, Lightdark, Allday) and delay time (3S, 40S, 4Min).

4.1. Illumination Adjustment (Adjustable Illumination)

This setting determines the ambient light level at which the sensor will become active.

  • Deepdark (<2LUX): The sensor will only trigger in extremely low light conditions, making it suitable for nighttime use.
  • Lightdark (<25LUX): The sensor will trigger in dim light, ideal for dusk or poorly lit environments.
  • Allday: The sensor will trigger at any time, regardless of the ambient light level.

4.2. Time Delay Adjustment (Adjustable Time Delay)

This setting controls how long the connected light remains on after motion is detected and then ceases.

  • 3S (3 Seconds): The light will stay on for 3 seconds after the last detected motion.
  • 40S (40 Seconds): The light will stay on for 40 seconds after the last detected motion.
  • 4Min (4 Minutes): The light will stay on for 4 minutes after the last detected motion.

5. Maintenance

  • Cleaning: Regularly clean the detection lens to prevent dust or oil accumulation, which can affect the sensor's performance. Use a soft, dry cloth.
  • Disassembly: Do not attempt to disassemble the product yourself. Unauthorized disassembly will void the warranty and may cause damage to the device.

6. Troubleshooting

  • Poor Sensitivity: If the sensor is not detecting motion effectively, check the following:
    • Verify that the installation height is appropriate (recommended 3.5m).
    • Ensure there are no obstructions blocking the sensor's field of view.
    • Adjust the illumination and/or delay settings to suit the environment.
  • Light Stays On Continuously: If the connected light remains on without motion, consider these points:
    • Check if the illumination setting is set to

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.