Herdio HOS-401

Contents

Herdio HOS-401 4-Inch Passive Outdoor Speakers

Instruction Manual

Introduction

Thank you for choosing Herdio HOS-401 4-inch passive outdoor speakers. These speakers are designed to deliver high-quality audio in various indoor and outdoor environments, featuring durable, weatherproof construction and versatile mounting options. This manual provides essential information for safe installation, operation, and maintenance of your speakers.

Herdio HOS-401 4-Inch Passive Outdoor Speakers
Herdio HOS-401 4-Inch Passive Outdoor Speakers, designed for superior sound quality and IP66 rated protection.

Important Safety Precautions

  • To avoid potential shorts in the electrical system, be sure to disconnect the (–) battery cable before installation.
  • Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction.
  • When replacing the fuse, be sure to only use a fuse of the rating specified on this product.
  • These speakers are designed to resist weather conditions like snow, rain, and sun, but should not be submerged in water.
  • For extended durability, consider removing speakers and storing them indoors during extreme temperatures (below 0 degrees or above 120 degrees).

What's Included

Your Herdio HOS-401 speaker package includes:

  • 2 x Passive Speakers
  • 2 x Mount Brackets
  • 2 x Speaker Wires (16.4 Feet / 5 meters)
Contents of the Herdio HOS-401 package
The Herdio HOS-401 package includes two passive speakers, mounting brackets, and speaker cables.

Setup & Installation

The Herdio HOS-401 speakers are passive and require an external amplifier for operation. This section guides you through the mounting and wiring process.

1. Speaker Placement

  • For optimal sound, place speakers no more than eight feet apart from each other.
  • Position speakers slightly higher than ear level.
  • The most ideal place to install outdoor speakers is under overhangs for best protection against weather elements.
Various usage scenarios for Herdio HOS-401 speakers
Herdio HOS-401 speakers are suitable for various indoor and outdoor settings like patios, parties, and meeting rooms.

2. Mounting the Speakers

The speakers feature a 90-120° Speed-Lock Mounting System for easy and secure installation.

  1. Remove the bracket knobs and the bracket from the speakers.
  2. Hold the bracket against your desired mounting surface. The speaker can be mounted either horizontally or vertically.
  3. Mark the locations for the screw holes. Ensure all holes are used for secure mounting.
  4. Drill pilot holes into the mounting surface.
  5. Align the bracket with the pilot holes and secure it to the mounting surface using appropriate screws (not included).
  6. Place the speaker onto the mounted bracket and tighten it with the bracket knobs.
  7. Adjust the speaker to the desired angle. Once the direction is set, tighten the bracket knobs securely.
  8. When possible, tilt the speakers downwards to enhance longevity and protect against weather.
Diagram of Speed-Lock Mounting System
The 90-120° Speed-Lock Mounting System allows for easy and secure speaker installation.
Outdoor speakers installed on a patio
Example of Herdio outdoor speakers installed on a patio.

3. Wiring the Speakers

The HOS-401 speakers are passive and require connection to an external amplifier. Use the provided speaker cables for connection.

  1. Identify the positive (+) and negative (-) terminals on the back of each speaker. The red terminal is for positive, and the black terminal is for negative.
  2. Gently turn the red and black terminals clockwise to unscrew them. You will see a small hole in the metal.
  3. Insert the speaker wire into the corresponding holes. Ensure the red wire connects to the red terminal and the black wire to the black terminal.
  4. Turn the terminals counter-clockwise to tighten them, securing the wires. Make sure the speaker wire insulation is not inserted into the hole to ensure good contact.
  5. Connect the other end of the speaker cables to your amplifier's speaker output terminals, matching positive to positive and negative to negative.
  6. If longer wire runs are needed, use 16 gauge weatherproof wire up to 50 feet.
Wiring diagram for passive speakers
Wiring diagram showing positive and negative connections for passive speakers.

Installation Video Guide

This video demonstrates the unboxing, mounting, and wiring process for the Herdio HOS-401 speakers.

Operating Instructions

Since the Herdio HOS-401 speakers are passive, their operation is dependent on the amplifier they are connected to. Follow the instructions provided with your amplifier for power, input selection, and volume control.

  1. Ensure all speaker wires are securely connected to both the speakers and the amplifier.
  2. Power on your amplifier.
  3. Select the desired audio input source on your amplifier (e.g., AUX, Bluetooth, etc.).
  4. Start playing audio from your source device.
  5. Adjust the volume on your amplifier to a comfortable listening level.

Note: These speakers do not have built-in Bluetooth or Wi-Fi capabilities. All audio input and control are managed by the external amplifier.

Maintenance

Cleaning

To clean your Herdio HOS-401 speakers:

  • Wipe the speaker cabinets with a soft, damp cloth.
  • Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish and weatherproof coating.
  • Do not spray water directly onto the speaker grilles.

Weather Protection

The speakers feature an all-weather resistant coating and are IP66 rated for protection against dust and powerful water jets. However, proper care can extend their lifespan:

  • While designed for outdoor use, avoid submerging the speakers in water.
  • During periods of extreme weather (e.g., heavy storms, prolonged freezing temperatures, or intense heat), consider temporarily removing the speakers and storing them indoors.
  • Ensure speakers are installed under overhangs or other protective structures when possible.
IP66 waterproof and dustproof speaker
The Herdio HOS-401 speakers are IP66 waterproof and dustproof.
Speaker with water droplets demonstrating weather resistance
The all-weather resistant coating protects the speakers from the elements.

Troubleshooting

ProblemPossible CauseSolution
No sound from speakersLoose or incorrect wiring
Amplifier not powered on or incorrect input selected
Volume too low on amplifier or source device
Check all speaker wire connections for proper polarity and secure fit.
Ensure amplifier is powered on and the correct input source is selected.
Increase volume on both the amplifier and the audio source.
Distorted or poor sound qualityLoose wiring
Overdriven amplifier
Damaged speaker or wire
Check all speaker wire connections.
Reduce the volume on the amplifier. Ensure the amplifier's power output matches the speaker's rating.
Inspect speaker cones and wires for visible damage. Replace if necessary.
Only one speaker workingFaulty wiring to one speaker
Balance setting on amplifier is off
Damaged speaker
Check wiring for the non-working speaker.
Adjust the balance control on your amplifier.
Test the speaker with another known-good cable or amplifier to isolate the issue.

Specifications

FeatureHOS-401HOS-501HOS-601
Power Output2X 100W Max Power2X 150W Max Power2X 200W Max Power
Woofer4" Injection Molded PP Cone Butyl Rubber Surround5.25" Injection Molded PP Cone Butyl Rubber Surround6.5" Injection Molded PP Cone Butyl Rubber Surround
Tweeter1" PEI Dome1" PET Dome1" PET Dome
ColorWhite/BlackWhite/BlackWhite/Black
Impedance4 Ohm
Sensitivity89dBN/AN/A
Frequency Response100Hz-20kHz
Waterproof RatingIP66 (Marine Grade)
Product Dimensions (L x W x H)8.62" (219mm) x 5.67" (144mm) x 6.62" (159mm)N/AN/A
Weight6.6 lbs./PRSN/AN/A
Product dimensions of Herdio HOS-401 speaker
Detailed product dimensions for the Herdio HOS-401 speaker.
Exploded view of speaker components and dimensions
Exploded view showing the tweeter and woofer components with overall dimensions.

User Tips

  • Optimal Sound: Experiment with speaker placement and angle to find the best sound dispersion for your listening area. Tilting them slightly downwards can improve sound projection.
  • Cable Management: Use cable ties or clips to neatly secure speaker wires, especially in outdoor installations, to prevent tripping hazards and protect cables from damage.
  • Amplifier Matching: Ensure your amplifier's power output is compatible with the speakers' power handling capabilities to prevent damage and achieve optimal sound.

Frequently Asked Questions (FAQ)

Q: Are these speakers wireless or Bluetooth enabled?
A: No, the Herdio HOS-401 speakers are passive and require an external amplifier for operation. They do not have built-in Bluetooth or Wi-Fi capabilities. Any wireless connectivity would come from your amplifier.
Q: Can these speakers be fully submerged in water?
A: No, while they are IP66 rated for protection against dust and strong water jets, they are not designed for full submersion. Avoid placing them where they could be submerged.
Q: What kind of amplifier do I need?
A: You will need an amplifier that can provide at least 100W per channel at 4 Ohms to power these speakers effectively. Ensure the amplifier's output matches the speaker's impedance.
Q: Are mounting screws included?
A: Mounting brackets are included, but the screws/nails for attaching the brackets to your wall or surface are not. You will need to provide appropriate hardware for your specific mounting surface.

Warranty & Support

All Herdio speaker products come with a 1-year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period, Herdio will replace any defective part and correct any defect in workmanship without charge for either parts or labor.

The Technical Support Center at HERDIO is available from Monday to Friday, excluding holidays. If you have any questions, please feel free to send your messages to our mailbox: support@herdiotech.com

For more information, please visit: www.Herdiotech.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.