1. Important Safety Instructions
Thank you for purchasing the HORLAT T10MAX Projector. Please read this manual thoroughly before using and keep it for future reference. The warranty does not apply if physical injury, loss of data, or damage is caused by failure to follow these instructions.
1.1. Set Up
- Do not install the projector in places without proper ventilation.
- Avoid hot, humid, dusty, or smoky environments.
- Do not block the ventilation holes (intake or exhaust).
- Do not install near temperature and smoke detectors, as it may cause sensor failure.
- Do not install where warm or cool air blows directly onto the projector, as this may cause failure due to moisture condensation or large temperature changes.
1.2. Power Supply
- Power off the device before removing the power supply from the socket.
- Use the power cord with caution to avoid undue bending; damaged cords may cause electric shock or fire.
- Unplug the device during lightning storms or when unused for long periods.
- Never touch the power cable or connection with wet hands.
- Unplug the power cord from the outlet after using the projector.
1.3. Repairs
- Never attempt to repair the projector yourself.
- No components in the projector can be repaired by customers.
- Please entrust qualified professional maintenance personnel for repair.
1.4. Caution
- Do not look at the lens directly, as it may cause severe eye injury.
- During and after use, the temperature near the air outlet will rise; avoid touching it to prevent burns.
- Do not place the projector in a room that is too warm or too cold, as high or low temperatures will shorten the device's lifespan. The optimal working temperature is 5°C-35°C.
2. Packing List
Please check the contents of your package:
Projector
Remote Control (Batteries not included)
HDMI Cable
AV Cable
Power Cable
User Manual (PDF version available for download)
3. Product Overview
Familiarize yourself with the projector's components and interfaces.

Front and Side View
- Focus Lens
- Adjusting Knob
- IR receiver
- 3.5mm port for audio output
- AV port
- Speaker
- IR receiver
- Removable dust cover

Rear and Top View
- Switch Of Removable Dust Cover
- USB port
- HDMI 1 port
- HDMI 2 port
- Power Switch
- Focussing ring
- Removable dust cover

Bottom View
- Adjusting Knob (Lifting nut)
4. Remote Control
The remote control allows for easy navigation and control of your projector. Ensure batteries are inserted correctly (not included).

- Power Switch
- Voice remote control
- Menu Button
- Confirm Button
- Direction Buttons (Up, Down, Left, Right)
- Back Button
- Home Button
- Volume+
- Volume-
- Mute
- Signal Source
- Set up
- Projection Settings
- Lens Forward
- Lens Backward
- One-click access buttons (e.g., YouTube, Netflix, Prime Video, Disney+)
5. Getting Started
5.1. Projector Placement
The projector can be placed in various configurations:

Front Projection Ceiling Mount

Rear Projection Ceiling Mount

Front Projection Table Mount

Rear Projection Table Mount
Notes on Installation:
- During installation, do not operate with electricity to avoid electric shock or circuit failure.
- Maintain a gap of at least 30 cm from the wall. Do not cover or block the projector's vents. Ensure adequate ventilation for performance and reliability.
- If using a projector screen mounted on the ceiling, the projector cannot be higher than the upper edge of the screen to avoid affecting the image.
5.2. Ceiling Installation

- Purchase a universal projector ceiling mount.
- Remove the four rubber pads on the bottom of the projector to reveal the screw holes.
- Use M4*10mm screws for installing the ceiling mount, then attach the projector.
5.3. Power On

1. Plug the power cord into an outlet.

2. Take off the lens cover.

3. Press the power button to turn on the projector.
5.4. Projector Distance & Size

The recommended projection screen is around 80 inches with a projection distance of approximately 8.92 ft. Ambient darkness will improve the clarity of the projected images.
| Distance | Screen Size (inch) |
|---|---|
| 5.11ft (1.56m) | 50 |
| 8.20ft (2.50m) | 80 |
| 10.26ft (3.13m) | 100 |
| 12.33ft (3.76m) | 120 |
| 15.41ft (4.70m) | 150 |
| 20.5ft (6.27m) | 200 |
6. Operating Instructions
6.1. Adjusting the Projected Image (Autofocus)
After adjusting the size and distance of the projector, if the image is still unclear, press the remote control's F+/F- buttons to adjust until a clear image is obtained.

Autofocus Adjustment Interface
6.2. Auto Obstacle Avoidance (Autofocus)
- Use the 'Projection Settings' button on the remote control to select 'Advanced Settings'.
- Select 'Automatic Obstacle' in the 'Advanced Settings' column. After the projector refocuses, it will automatically avoid obstacles (the display screen will shrink).

Auto Obstacle Avoidance Settings
6.3. Auto Access Screen (Autofocus)
- Use the 'Projection Settings' button on the remote control to select 'Advanced Settings'.
- Select 'Automatic screen entry' in the 'Advanced Settings' column. After the projector refocuses, the screen size will be adjusted to fit the screen.
Note: The curtain needs to be selected with a black border; otherwise, it will not enter the curtain successfully. When entering the curtain automatically, please ensure that the corners of the curtain are within the projection screen.

Auto Access Screen Settings
6.4. Manual Four-Point Keystone Correction
- Use the 'Projection Settings' button on the remote control to select 'Advanced Settings'.
- Select 'Image Correction' in the 'Advanced Settings' column. Press the confirmation key to enter manual key correction. Use the remote control direction keys to zoom the screen size, and press the confirmation key to switch to the next corner.
Note: The projection screen can only be reduced, not enlarged. If the screen cannot be covered, move the projector back. After adjusting the screen, turn off autofocus and auto trapezoid in advanced settings.

Manual Keystone Correction Interface
6.5. Input Source Selection
6.5.1. HDMI Mode
- Connect the projector and equipment with an HDMI cable.
- Press and hold the 'Source' button on the projector or remote control to enter the input source interface and select HDMI.
- Select the HDMI cable connected to the corresponding interface (HDMI1 or HDMI2). Press the OK key to enter, and the return key to exit and return to the main interface.

HDMI Input Source Selection
6.5.2. AV Mode
- Connect the projector and equipment with an AV cable.
- Press and hold the 'Source' button on the projector or remote control to enter the input source interface.
- Select AV. Press OK to enter, and the return key to exit and return to the main interface.

AV Input Source Selection
6.5.3. USB Mode
- Connect a USB disk to the projector. The USB disk will be highlighted on the main interface.
- Select the corresponding Movie, Music, Picture, or Office Suite modules for the file type, and press OK to enter the file.

USB Input Source Selection
6.6. Screen Mirroring
- Connect both your phone and the projector to the same Wi-Fi network.
- For Apple phones: Swipe up to enter the options interface, click the screen mirror icon, select the projector name (e.g., 'TV Stick'), and then click 'Connect'.
- For Google phones: Swipe down to enter the options interface, select 'Screen Cast', select the projector name (e.g., 'TV Stick'), and then click 'Connect'.
Screen Mirroring Interface on Phone
6.7. Bluetooth Connection
To connect the projector to external speakers:
- Use the remote control or projector button to enter the projector's settings interface.
- Find 'Bluetooth settings' in the settings interface. Press OK to enter.
- Select 'Add accessory'. A list of Bluetooth devices will be displayed.
- Select the desired Bluetooth speaker from the device list to connect, then press OK to pair.
- After successful connection, the Bluetooth device will show as connected.
Bluetooth Connection Settings
7. Specifications
| Feature | Specification |
|---|---|
| Display Technology | LCD |
| Light Source | LED |
| Aspect Ratio | 16:9/4:3/Auto |
| Focus | Manual / TOF Auto Focus/Keystone |
| Keystone Correction | Manual Correction, Electronic Correction, Auto Correction |
| Projection Mode | Throwing, Ceiling, Back Projection, Mirror Image |
| Speaker | 5W*2 (Built-in Speaker: Yes) |
| Power Supply | AC 110-240V, 50/60Hz |
| Unit Dimension | 256.9*219.6*101.5 mm |
| Unit Net Weight | 2.6kg |
| Photo Format Supported | JPG/JPEG/PNG/BMP |
| Audio Format Supported | MP3/APE/AAC/FLAC/OGG/WAV/WMA/MID/DTS/M4A |
| Video Format Supported | 3GP/AVI/FLV/MP4/MPG/VOB/TS/M2TS/RMVB/MKV |
| Ports | HDMI *2 / USB 2.0 *1 / Audio in *1 / AV out *1 |
| System | Android (Google TV) |
| Ansi Lumens | 3000 |
| Brightness | 45000 Lumens |
| Optical Resolution | 1920x1080dpi (Full HD) |
| Support | HDR10, Red and Blue 3D, 4K, 8K decoding, Auto Keystone, Automatic obstacle avoidance, Automatic entry |
| Bluetooth | Bluetooth 5.4 |
| Light Source Life | >100,000 hours |
| Processor Type | HI3751/GPU Mali-450MP2 |
| Functional Interface | AUDIO out x1. Panel buttons: Power (switch) key, left key, right key, up key, down key, OK key, BACK (return) key, source key, pause key |
| Support Mobile Hard Disk | 1T, U disk FAT32: 8G/16G/32G, 64G |
8. Troubleshooting
8.1. Blurry Image
- Ensure the projection distance is greater than the minimum projection distance of 1.5 m.
- Adjust the focus ring.
8.2. No Signal Displayed
- Make sure all cables are connected properly and stably.
- Check if the correct input source mode has been selected (e.g., if using HDMI, ensure HDMI input channel is selected).
8.3. Remote Unresponsive
- Ensure the remote points directly at the IR receiver.
- Do not cover the IR receiver.
- Try a new pair of AAA batteries.
8.4. Projector Shuts Down Automatically
- Check if the projector's air inlet and outlet are blocked by other objects.
- Ensure the local mains voltage is stable and within the acceptable range (not too low or too high).
9. User Tips
- Quiet Operation: The projector operates quietly, making it suitable for movie nights without distracting fan noise.
- Image Quality: The projector delivers clear and bright images, performing well even in dim-light rooms. For best results, use a white background or screen.
- Easy Setup: The auto-focus and auto-correction features make setup effortless, providing a perfectly framed projection quickly.
- Connectivity: Easily connects to mobile phones, tablets, and other devices for wireless screen sharing. The official Google TV system supports many streaming apps directly.
- Sound: The built-in speakers provide powerful and clear sound, often sufficient for home use without needing additional external speakers.
10. Warranty and Support
For detailed warranty information and further support, please refer to the official user manual PDF available for download. The PDF contains comprehensive details on product care, service, and warranty claims.
You can access the PDF manual here.