ATOPCARE PR903W

Contents

ATOPCARE PR903W 8K 60MP Solar Powered WiFi Trail Camera

User Instruction Manual

1. Camera Overview

This section provides a visual guide to the main components of your ATOPCARE PR903W Trail Camera and explains the function of its operation keys.

Internal view of ATOPCARE PR903W Trail Camera showing LCD screen, control buttons, and various slots.

Figure 1: Internal components of the PR903W Trail Camera.

1.1. Camera Components

  1. 2.0" LCD Display Screen
  2. Power Switch (OFF-TEST-ON)
  3. USB Slot
  4. SD Card Slot
  5. DC 6V Interface
  6. Battery Box
  7. Solar Panel

1.2. Operation Keys (Switch to SETUP/TEST Mode)

Key/Switch PositionFunction
OFFPower off the camera.
TESTActivates the screen for menu navigation, parameter settings, and mode selection.
ONAfter 5 seconds, the screen turns off, and the camera enters infrared sensor (motion detection) mode.
MENUWhen the screen is on, press to access camera settings and functions.
SHOTManually take a photo or record a video.
MODEManually switch between photo, video, and replay modes.
OKConfirm selected options or settings.

2. Setup and Installation

2.1. Initial Preparation

  • SD Card Formatting: Always format the SD card before first use and periodically to ensure optimal performance.
  • Battery Charging: Fully charge the camera using the Type-C cable. For extended standby time, install 8 x 1.5V AA alkaline batteries.
  • Protective Film: Remove the protective film from the camera's PIR sensor to avoid affecting shooting performance.

2.2. Power Supply Options

Your camera offers multiple ways to ensure continuous power:

  1. Solar Panel with Built-in Battery: The integrated solar panel charges a 5200mAh lithium battery using sunlight. It can also be charged via a Type-C cable.
  2. AA Batteries: Install 8 x 1.5V AA alkaline batteries into the battery compartment. Ensure correct polarity (+/-). The camera will use AA batteries only after the solar panel's built-in battery is exhausted.
    Open camera showing the battery compartment with 8 AA batteries inserted.

    Figure 2: Installing AA batteries into the camera.

  3. External 6V DC Power: Use the provided 6V cable to power the camera directly. Note that if there is no built-in battery, the camera will turn off when unplugged.

2.3. Quick Start Guide

  1. Power On: Switch the camera to the TEST position and wait for the screen to light up.
  2. Access Settings: Press the MENU button to enter camera settings (Mode, Photo Pixel, Video Resolution).
  3. Format SD Card: Navigate to "Memory Card Format" and select YES to format your SD card.
  4. Activate Motion Detection: Switch the camera to the ON position. The camera will enter motion detection mode. After 10 seconds, the screen will turn off, and the camera will begin working. It will record photos/videos upon detecting movement.

2.4. Mounting the Camera

Proper placement is crucial for optimal performance and accurate recordings.

  • Height: Fix the camera at a height of 1-2 meters (3-6.5 feet) from the ground. For optimal photo quality, place it 0.75-1m (2.5-3.5ft) high. Avoid placing it too low (small creatures) or too high (shadows, ground temperature changes).
  • Angle: Keep the camera lens at a 45-degree angle to the target position for the best shooting angle.
  • Orientation: Position your camera facing north or south to minimize false triggers caused by the rising or setting sun. Avoid east or west facing.
  • Distance to Target: For optimal night results, ensure the subject is within 3-30 meters (10-98 feet) from the camera.
  • Background: Position the camera in an area with a backdrop to reflect maximum light, enhancing flash effectiveness.
  • Clear View: Clear all vegetation (small limbs, twigs, leaves, grass) from in front of the camera to prevent false triggers from wind movement.
  • Stability: Mount the camera securely on a stable surface, preferably a tree with a diameter over 15cm (6 inches) that won't sway in the wind.

2.5. Sensing Angle and Distance Test

To ensure effective monitoring, perform a test of the camera's sensing area:

  1. Toggle the power switch to TEST.
  2. Move around in front of the camera at various positions and distances within your intended monitoring area.
  3. Observe the red indicator LED light. If it blinks, that position is within the sensing area. If it does not blink, that position is outside the sensing area.
  4. Adjust camera placement as needed based on test results.

3. Operating Instructions

To access detailed settings, move the power switch to the SETUP position and press the MENU key. Use OK to confirm and MENU again to return.

3.1. Recording Modes

  • Motion Detection: Camera records only when motion is sensed. If no motion, it enters standby. Detection Delay can be set from 5 seconds to 1 hour.
  • Time-lapse Normal: Camera records continuously at set intervals, regardless of motion. Each video is saved separately. E.g., capture 15 seconds of video every 5 minutes.
  • Time-lapse Video: Camera takes multiple photos at intervals and automatically combines them into a video (up to 360 photos per video). New videos are created if resolution changes, mode switches, or 360 photos are reached.

3.2. Camera Settings

  • Work Time (Off/ON): Customize the camera's active working hours (e.g., 22:00-07:00).
  • Photo or Video (Photo/Video/Photo & Video): Select the desired capture mode.
  • Photo Resolution: Options include 2M, 4M, 8M, 16M, 20M, 24M, 32M, 36M, 42M, 48M, 60M.
  • Video Resolution: Options include 720P, 1080P, 2.7K, 4K, 8K.
  • Photo Burst (1P-5P): Set the number of images taken per trigger (1 to 5 photos).
  • Video Length: Set video duration from 5 seconds to 10 minutes (default 10 seconds).
  • Audio Recording (ON/OFF): Enable or disable sound recording with videos.
  • Detection Delay: Set the interval between motion detections (5 seconds to 1 hour, default 30 seconds).
  • PIR Sensitivity (Low/Middle/High): Adjust motion sensor sensitivity based on shooting distance (Low: 3-4m, Medium: 7-8m, High: 12-15m).
  • Motion Test: Use this function to verify PIR sensor functionality.
  • Fill Light Distance (Near/Middle/Far): Adjust infrared fill light distance for night shooting (Low: 3-4m, Medium: 7-8m, High: 12-15m).
  • Camera Name (ON/OFF): Set a custom name to be displayed on photos/videos.
  • Date & Time: Manually set or sync camera time via the app.
  • Date Format: Choose D/M/Y, M/D/Y, or Y/M/D.
  • Time Format: Choose 24H or 12H.
  • Loop Record (ON/OFF): If ON, new files overwrite old ones when the SD card is full. If OFF, recording stops.
  • Memory Card Format: Deletes all files on the SD card.
  • Language: Select from multiple languages including English, Deutsch, Français, Español, etc.
  • Password Protection (Off/ON): Set a 4-digit password. To reset, hold "^" + "OK" and switch to SETUP.
  • Factory Reset: Restore camera to default settings.
  • Version Info: View camera firmware version.

3.3. Playback and File Management

Press the REPLAY key to enter playback mode. Use up/down keys to navigate, OK to play/pause. Press MENU to delete current or all files.

3.4. App Connection (TrailCam Go Mobile APP)

The TrailCam Go app allows remote control, live view, file management, and settings adjustment.

Trail camera with solar panel, showing Wi-Fi and Bluetooth icons, and a smartphone displaying a deer captured by the camera.

Figure 3: Connecting the camera to a smartphone via Wi-Fi/Bluetooth.

  1. Download App: Scan the QR code in the manual or search "TrailCam Go" on App Store (iOS) or Google Play (Android).
  2. Permissions: Grant necessary permissions (Wi-Fi, Bluetooth, storage, location, camera access) for the app to function correctly. iOS 14+ users need to enable local network permissions.
  3. Enable Wi-Fi & Bluetooth: Ensure both are enabled on your mobile phone before launching the app for optimal connection speed.
  4. Adding a Camera:
    • Stay close to the camera and avoid excessive electrical interference.
    • Tap "Wi-Fi Camera" in the app to select device type.
    • The app will search for nearby Wi-Fi cameras. Select your camera (e.g., "TrailCam XXXX").
    • Allow up to 30 seconds for Bluetooth and Wi-Fi connection. Click "Join" if prompted for Wi-Fi connection.
  5. App Navigation:
    • Camera: Live view, manual capture/record.
    • Gallery: View photos/videos on the camera, download to phone.
    • Status: Check battery life, SD card capacity, internal temperature, camera mode.
    • Settings: Modify camera settings, which sync automatically.
  6. Disconnect/Reconnect: Disconnect from the app to browse the internet or adjust camera settings. Reconnect via the "Camera" section.
  7. App Password: Configure a 4-digit pass code for camera and app security via Camera > Settings > Security.
  8. Account Registration: Register an account after binding the device to the app for enhanced content security.

3.5. Power Cord Functions

  • USB Cable: Connects the camera to a computer for viewing SD card files. Does not charge the camera.
  • DC 6V Cable: Powers the camera directly. If no built-in battery, the camera turns off when unplugged.

4. Maintenance

  • SD Card Care: Format the SD card regularly to maintain optimal performance and prevent data corruption.
  • Battery Management: Ensure batteries are fully charged before deployment. Replace AA batteries when low.
  • Lens Cleaning: Gently clean the camera lens with a soft, lint-free cloth to ensure clear image quality. Avoid abrasive materials.
  • Condensation: If water mist appears inside the lens due to temperature differences, place the camera in a dry environment for 1-2 days to allow it to dissipate.
  • Storage: When not in use for extended periods, remove all batteries and store the camera in a cool, dry place.

5. Troubleshooting

Q1: Can't connect to home Wi-Fi router?
The Wi-Fi trail camera connects only to your phone via the TrailCam Go app, not for internet surfing. It's designed for direct photo/video transfer and setup.
Q2: Camera not found on App or not connected?
  • Get as close as possible to the camera (within 45ft for Bluetooth).
  • Move away from other electronic products.
  • Ensure the camera is turned ON (Test or On mode).
  • Check camera battery level.
  • Verify both Bluetooth and Wi-Fi are enabled on your phone.
Q3: Why did the camera stop connecting after it was just connected?
  • You left the app for over 2 minutes.
  • You visited other apps requiring cellular connection or clicked the "Map" option in the camera interface, which disconnects Wi-Fi to switch to cellular.
Q4: Cannot take photos or videos?
  • No TF (SD) card in the slot.
  • Corrupt TF (SD) card.
  • Batteries are too low to power the camera.
Q5: The photo is too dark at night?
  • Illumination parameter is not set correctly (check camera flash range settings).
  • Lack of reflective background: Position the camera in an area with a backdrop to reflect maximum light (e.g., 8-12m from a field edge facing woods).
  • Low battery power.
Q6: The camera shut down automatically in TEST mode?
The camera automatically powers off after 3 minutes of inactivity in TEST mode to conserve battery.
Q7: Camera LED light area appears water mist?
This is condensation due to temperature differences. Place the camera in a dry place for 1-2 days to resolve.
Q8: How do I change the language of the camera back to English?
In TEST mode, select Menu, then navigate to the fourth-to-last button to change the language.
Q9: Apple computer cannot read video files?
Video files are AVI format, which may not be compatible. Try a different video player.
Q10: Three ways to get an image?
  • Check photos on the TrailCam Go App.
  • Connect the camera to a computer via USB cable (without removing SD card); it will appear as a USB drive.
  • Insert the SD card into a card reader and connect to a computer.
Q11: No photos were taken in motion detection?
  • Remove all protective film from the camera lens.
  • Ensure the subject is within 35 meters (115 ft).
  • In Menu > Mode > Motion Detection, set the detection delay time to a few seconds.
  • In Menu > Work Time, select "Open" and set desired working hours.
  • In Menu > PIR Sensitivity, increase sensitivity for faster recognition (may increase power consumption).
  • In Menu > Detection Delay, set frequency of photos.
  • Use "Motion Test" to verify detection.
  • Ensure the camera is switched to "ON" to start auto shooting.

6. Specifications

FeatureDetail
Model NumberPR903W
Brand NameATOPCARE
Screen Size2.0 inches
Photo ResolutionUp to 60MP (60/48/42/36/32/28/24/20/14/9MP)
Video ResolutionUp to 8K (8K/4K/2.7K/1080P/720P)
Trigger Time0.2 ~ 0.5 seconds
Infrared Distance15-20 meters
Power SupplySolar panel + 5200mAh lithium battery + 8 AA batteries
MemoryUp to 128GB SD card
CertificatesCE, ROHS, FCC
OriginMainland China

7. User Tips

  • SD Card Maintenance: Always format your SD card directly in the camera before each use or after transferring files to ensure compatibility and prevent errors.
  • Optimal Placement: For best results, mount the camera facing north or south to avoid sun glare and false triggers. Clear any vegetation in front of the lens.
  • Battery Life Extension: Utilize the solar panel for primary power. Only use AA batteries as a backup once the internal solar battery is depleted.
  • App Connection Stability: When connecting via the TrailCam Go app, ensure your phone's Wi-Fi and Bluetooth are enabled, and stay close to the camera for a stable connection.
  • Night Vision Clarity: If night photos are too dark, ensure there's a reflective background behind your target area and check the "Fill Light Distance" setting.
  • Password Reset: If you forget your camera password, hold the "^" key and "OK" key simultaneously while switching the camera to the SETUP position.

8. Warranty and Support

For detailed warranty information, please refer to the product packaging, the seller's terms of sale, or contact ATOPCARE customer support directly. This manual provides operational instructions and does not constitute a warranty statement.

For further assistance or technical support, please consult the official ATOPCARE website or contact your retailer.

A comprehensive user manual in PDF format can be found at: Trail Camera WiFi Solar User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.