1. Product Overview
The YIHUA 926LED Soldering Iron Station is a versatile tool designed for both soldering and desoldering operations on SMT (Surface-Mount Technology) and through-hole components such as SOP, DIP, and SOIC. It features precise temperature control, a clear LED display, and various helpful accessories to enhance your soldering experience.

Product Components:
- Soldering Iron
- Temperature Display (LED)
- Menu Button / Temperature Adjustment Dial
- Residue Tray
- Soldering Iron Cord Assembly
- Soldering Helping Hands (2x)
- Soldering Iron Holder
2. Setup Instructions
- Place the Soldering Iron Holder: Securely place the soldering iron holder in its designated slot on the station. If your kit includes a solder roll holder, install it on the left side of the station, aligning the holes and tightening any screws.
- Connect Helping Hands: Insert the flexible arms of the helping hands into the designated ports on the station base. Ensure they are firmly seated.
- Insert Soldering Tips: Place your desired soldering tips into the storage holes on the station's tip holder.
- Connect Power: Plug the power cord into the station and then into a suitable electrical outlet. Ensure the voltage matches your unit's requirements (110V US, 220V EU, 230V UK, or 240V AU).


3. Operating Instructions
- Power On: Flip the power switch located on the station. The heating element will begin to heat up, and the LED display will show the current temperature. The heating indicator light will be constantly ON during heating and will blink when the temperature stabilizes.
- Initial Tip Preparation (First Use): For the first use of a new soldering tip, set the temperature to $250^{\circ}C$ ($482^{\circ}F$). Once the tip is hot enough to melt solder, apply a small amount of solder to coat the tip completely. This 'tins' the tip and helps prevent oxidation. After tinning, adjust the temperature to your desired working value.
- Temperature Adjustment: Use the single control dial to adjust the temperature. Rotate clockwise to increase and counter-clockwise to decrease. The LED display will show the set temperature. The station features PID temperature stabilization for quick recovery.
- °C/°F Unit Conversion: To switch between Celsius and Fahrenheit:
- Press and hold the menu dial button for approximately 2 seconds. The display will show 'C'.
- Rotate the dial to select 'C' for Celsius or 'F' for Fahrenheit.
- Press the menu dial button 3 consecutive times to confirm and exit the setting.
- Sleep Mode: The station features a sleep mode to extend tip life and save energy.
- To set sleep mode: Press and hold the menu dial button for 2 seconds, then press it once. The display will show 'L10' (10 minutes).
- Rotate the dial to select sleep duration: 0, 5, 10, or 30 minutes. 'L00' disables sleep mode.
- Press the menu dial button 2 consecutive times to confirm and exit.
- When in sleep mode, the temperature will drop to $200^{\circ}C$ ($392^{\circ}F$) if the set temperature is $\ge 250^{\circ}C$ ($482^{\circ}F$), or to $90^{\circ}C$ ($194^{\circ}F$) if the set temperature is $< 250^{\circ}C$ ($482^{\circ}F$).
- To wake up the station: Gently shake the soldering iron, press any button on the control panel, or power cycle the station.
- Temperature Calibration: This function allows you to fine-tune the temperature reading for accuracy.
- After the soldering iron temperature has stabilized, press and hold the menu dial button for 2 seconds, then press it 2 consecutive times. The display will show 'CAL'.
- Rotate the dial to enter the calibrated temperature. Confirm by pressing the dial button once.
- Press the dial button once more to complete and exit. Repeat if further adjustment is needed.


4. Maintenance and Precautions
- Tip Cleaning: After each use, clean any residual solder from the tip using a damp cleaning sponge or a metallic wool ball. Always 'tin' the tip with a fresh layer of solder after cleaning to prevent oxidation.
- Oxidized Tips: If the tip becomes oxidized (solder doesn't melt easily), DO NOT increase the temperature. Instead, clean the tip with a metal wool ball: set temperature to $300^{\circ}C$ ($572^{\circ}F$), gently rub the tip in the wool, and apply solder while rubbing until the tip is fully coated. If the tip is severely oxidized, replace it.
- Avoid Files: Never use metal files or abrasive materials to clean the soldering tip, as this will damage the tip's plating. Replace deformed or rusted tips.
- Gentle Use: Do not apply excessive force on the soldering tip while soldering. This does not improve heat transfer and can damage the tip.
- Idle Temperature: When placing the soldering iron back in the holder for extended idling after high-temperature operation, adjust the temperature to $250^{\circ}C$ ($482^{\circ}F$) or below. This prevents accelerated aging of the heating element and prolongs the lifespan of both the heating element and the soldering tip.
- Power Off: If the soldering station will not be used for an extended period, turn off the power switch and disconnect the power cord.