WMARK NG-8613 Kit

Contents

WMARK Professional Haircut Kit

Model: NG-8613 Kit

Introduction

This manual provides essential information for the safe and effective use of your WMARK Professional Haircut Kit (NG-8613 Kit). Please read all instructions carefully before using the product and retain this manual for future reference.

Product Information

  • Product Name: Hair Clipper
  • Product Model: NG-8613 Kit
  • Manual Version/Batch Number: NG-V3

Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

Package Contents

The WMARK NG-8613 Kit includes the following items:

WMARK NG-8613KIT - Full kit contents

Figure 1: Complete WMARK NG-8613 Kit contents.

  • 1x Hair Clipper (NG-8613C)
  • 1x Hair Trimmer (NG-8613T)
  • 6x Magnetic Guide Combs (1.5/3/4.5/6/10/13mm) for NG-8613C
  • 4x Guide Combs (1.5/3/6/9mm) for NG-8613T
  • 2x USB Charging Cables
  • 2x Cleaning Brushes
  • 2x Hair Stickers
  • 2x Hair Combs
  • 1x Hair Brush
  • 1x Zero Gap Tool
  • 2x Instruction Manuals

Setup

Before First Use

  1. Remove all protective films from both the hair clipper and hair trimmer devices.
  2. Ensure all components are present as listed in the "Package Contents" section.

Charging the Device

Before initial use, fully charge both the hair clipper and hair trimmer.

Charging methods for WMARK Haircut Kit

Figure 2: Various charging methods for the WMARK Haircut Kit.

  • Connect the provided USB cable to the charging port on the device or its charging base.
  • Connect the other end of the USB cable to a certified 5V power adapter (e.g., car charger, computer USB port, power bank, or standard USB wall adapter).
  • Charging Time:
    • NG-8613C (Clipper): Approximately 3.5 hours
    • NG-8613T (Trimmer): Approximately 2.0 hours
  • The device will indicate charging status (e.g., LED indicator).

Operating Instructions

Power On/Off and Mode Selection

  • To Turn On: Press and hold the power button for 3 seconds.
  • To Change Modes/Speeds: Short press the power button to cycle through available speed settings.
  • To Turn Off: Press and hold the power button for 3 seconds.

Speed Settings

Both the clipper and trimmer feature multiple speed settings for versatile grooming.

Double speed adjustment for WMARK Haircut Kit

Figure 3: Dual speed settings for precise control.

  • NG-8613C (Clipper): 7500 RPM / 8500 RPM
  • NG-8613T (Trimmer): 6500 RPM / 7500 RPM

Adjusting Cutting Length

The devices offer adjustable cutting lengths for various styles.

5 adjustable cutting length levels

Figure 4: Five adjustable cutting length levels for precision.

  • NG-8613C (Clipper): Features 5 adjustable cutting length settings directly on the blade lever.
  • Guide Combs: Attach the appropriate magnetic guide comb (for NG-8613C) or standard guide comb (for NG-8613T) to achieve desired hair lengths. Ensure the comb is securely attached before use.

General Usage

Hair cutting and styling with WMARK kit

Figure 5: The kit is suitable for both general hair cutting and detailed styling.

  • Ensure hair is clean and dry for best results, unless performing a wet haircut (if applicable).
  • Start with a longer guide comb if unsure of the desired length.
  • Move the clipper/trimmer against the direction of hair growth for an even cut.
  • Use the trimmer for detailing, outlining, and creating sharp lines.

Maintenance

Cleaning

  • Clean Method: Brush cleanup.
  • After each use, turn off the device and use the provided cleaning brush to remove hair clippings from the blades and housing.
  • Do not rinse the device under water unless explicitly stated as waterproof (refer to specifications).
  • Regularly oil the blades with a small drop of clipper oil (not included due to shipping regulations) to maintain performance and longevity.

Storage

  • After use, turn off the device and store it in a dry place.
  • Keep the device and its accessories in a safe place, away from children.

Troubleshooting

If you encounter any issues with your WMARK Professional Haircut Kit, please refer to the following common solutions:

  • Device not turning on: Ensure the device is fully charged. Check the power button operation.
  • Poor cutting performance: Clean the blades thoroughly. Apply clipper oil to the blades. Ensure blades are not damaged.
  • Device making unusual noise: Clean and oil the blades. If the noise persists, contact support.
  • Battery not charging: Ensure the USB cable and power adapter are working correctly. Check the charging port for any obstructions.

For persistent issues not resolved by the above steps, please refer to the Warranty & Support section.

Specifications

Product dimensions of WMARK Haircut Kit

Figure 6: Detailed product dimensions for the clipper, trimmer, and packaging.

FeatureNG-8613C (Clipper)NG-8613T (Trimmer)
ModelNG-8613 Kit
Size & Weight285g205g
Working Time~120 Minutes~120 Minutes
Charging Time~3.5 Hours~2.0 Hours
Product MaterialABS
VoltageGlobal Universal (100-240V)
Blade MaterialPowder Metallurgy Fixed Fade Blade with Ceramic Moving BladePowder Metallurgy DLC Fixed Blade with Ceramic Moving Blade
Clean MethodBrush cleanup
RPM7500 / 8500 RPM6500 / 7500 RPM
Battery2500mAH Lithium-ion1400mAH Lithium-ion
Rated Power5W
Commodity Quality Certification3C, CE, UL, GS
OriginMainland China

Warranty & Support

Warranty Information

All WMARK products come with a 0.5-year (6-month) warranty from the date of purchase. Please refer to your purchase documentation for the exact warranty period applicable to your product.

If the item is damaged during shipping, please contact the seller first and ensure the item remains in its original condition. The seller will review your situation and provide a solution accordingly.

Manufacturer Information

  • Manufacturer: Ningbo Woji Electric Appliance Co., Ltd.
  • Address: CN-CN-No. 656, Kaifa East Road, Zhouxiang Town, Cixi City, Ningbo, Zhejiang.
  • Email: Tiger-Zhou@web.de

EU Authorized Representative

  • Representative: Jorge Wilsone
  • Address: CASTELLANA 9144, 28046 Madrid.
  • Phone: 34-688185858

For any support inquiries, please contact the seller or manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.