1. Introduction
1.1 Product Profile
The LAUNCH X-431 PROS Elite inherits advanced LAUNCH diagnostic technology, covering a wide range of vehicles with powerful functions and providing precise test results. Through simple cable communication between the tablet and the vehicle, it achieves comprehensive car model and full-system vehicle problem diagnosis, including DTC reading, DTC clearing, data stream reading, actuation tests, and special functions.
Key features include: Intelligent Diagnosis, Local Diagnosis, Remote Diagnosis, Service Function, One-Click Update, ADAS Calibration, TPMS, Diagnostic History, Feedback, Vehicle Coverage, and Additional Modules.
1.2 Important Notes and Messages
- Note: Provides useful information such as additional explanations, tips, and comments. For example, if the battery is not used for a long time or is completely discharged, it is normal for the tool not to turn on while charging. Please charge it for 5 minutes before turning it on.
- Warning: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury to the operator or bystanders. For example, using DTCs to troubleshoot vehicle malfunctions is only part of a general diagnostic strategy. Never replace a part based solely on the DTC definition.
- Danger: Indicates an imminent or potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or bystanders. For example, if you must drive the vehicle to perform a troubleshooting procedure, have a second person assist you. Driving and operating the diagnostic tool at the same time is dangerous and could cause a serious traffic accident.
2. Important Safety Precautions
To prevent personal injury, property damage, or accidental product damage, read all information in this section before using the tool.
2.1 DANGER
- When an engine is running, keep the service area well-ventilated or connect a building exhaust gas extraction system to the engine exhaust system. Engines produce various poisonous compounds (hydrocarbons, carbon monoxide, nitrogen oxides, etc.) that cause slower reaction times and lead to death or serious personal injury.
- Please use the included battery and power adapter. Risk of explosion if the battery is replaced with an incorrect type.
- DO NOT attempt to operate the tool while driving the vehicle. Have a second person operate the tool. Any distraction can cause an accident.
2.2 WARNING
- Always perform automotive tests in a safe environment.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Before starting the engine, place the gear lever in Neutral (for manual transmission) or Park (for automatic transmission) to prevent injury.
- NEVER smoke or allow a spark or flame near the battery or engine. Do not use the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Keep a suitable fire extinguisher nearby for gasoline/chemical/electrical fires.
- Wear ANSI approved eye protection when testing or repairing vehicles.
- Place blocks in front of the drive wheels and never leave the vehicle unattended during testing.
- Be very careful when working near the ignition coil, distributor cap, ignition wires, and spark plugs. These components create dangerous voltages when the engine is running.
- To avoid damaging the tool or generating false data, ensure the vehicle battery is fully charged and the connection to the vehicle's DLC (Data Link Connector) is clear and secure.
- Car batteries contain sulfuric acid which is harmful to the skin. In operation, direct contact with car batteries should be avoided. Keep ignition sources away from the battery at all times.
- Keep the tool dry, clean, free of oil, water, or grease. Use a mild detergent on a clean cloth to clean the exterior of the equipment when necessary.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Store the tool and accessories in a closed area out of reach of children.
- Do not use the tool while standing in water.
- Do not expose the tool or power adapter to rain or humidity. Water entering the tool or power adapter increases the risk of electric shock.
- This tool is a sealed unit. There are no user-serviceable parts inside. All internal repairs must be performed by an authorized repair center or qualified technician. If you have any questions, contact the distributor.
- Keep the tool away from magnetic devices because their radiations can damage the screen and erase data stored in the tool.
- Do not attempt to replace the internal rechargeable lithium battery. Contact the distributor for factory replacement.
- Do not disconnect the battery or vehicle wiring harnesses when the ignition switch is on, as this could damage the sensors or the ECU.
- Do not place any magnetic objects near the ECU. Disconnect the power supply to the ECU before performing any welding operation on the vehicle.
- Be very careful when performing any operation near the ECU or sensors. Ground yourself when removing the PROM, otherwise, static electricity can damage the ECU and sensors.
- When reconnecting the ECU wiring harness connector, ensure it is firmly attached, otherwise electronic components, such as Integrated Circuits inside the ECU, may be damaged.
3. Package Contents
The following packing list is for reference only. Accessories may vary for different destinations. For more details, consult the seller or check the packing list provided with this tool.
- Main tablet (Display Tablet) x 1
- Diagnostic cable x 1
- Power Adapter x 1
- Switching Adapter x 2 (EU/US/UK Plug)
- Type-C USB cable x 1
- Quick Start Guide x 1
- User Manual x 1
- Plastic Suitcase x 1
Note: This model does not contain an OBD1 adapter kit; it only includes an OBD2 connector cable.

4. Components and Controls
4.1 Top View

- USB Type-C Port: Connects to an AC power outlet for charging. Connects to PC for data exchange.
- USB Type-A Port: Connects to compatible additional modules or USB storage devices.
- DB-15 Diagnostic Connection: Connects the diagnostic cable.
- POWER Key:
- In Off mode, press for 3 seconds to turn on the tablet.
- In On mode: Press once to activate the LCD screen if it is off. Press once to turn off the LCD screen if it is on. Press and hold for 3 seconds for a normal shutdown. Press and hold for 8 seconds for a forced shutdown.
- Charging LED: Red indicates charging; Green indicates fully charged.
4.2 Front View

- LCD Screen: Displays test results.
4.3 Rear View

- Camera Flash: Provides illumination for the rear camera.
- Adjustable Stand: Unfold it to work comfortably at any angle on your desk, or hang it on the steering wheel.
- Rear Camera: 8.0MP camera for taking photos.
- Speakers: For audio output.
5. Setup and Initial Use
5.1 Charging and Power On
- Use the included power adapter to charge the tablet.
- Once charging is complete, press the POWER button to turn on the tablet. The system will initialize and then enter the home screen.
Note: If the battery has not been used for a long time or is completely discharged, it is normal for the tool not to turn on while charging. Please charge it for 5 minutes and then turn it on.
Warning: Use the included power adapter to charge your tool. No responsibility can be assumed for any damage or loss caused by using power adapters other than the one supplied.
Press [POWER] for 3 seconds, and an options menu will appear on the screen. Tap 'Power Off' to turn off the tool.
5.2 Screen Layout
There are five on-screen buttons available at the bottom of the screen:
- Home: Navigates to the Android home screen.
- Recent Apps: Shows running applications.
- Connection: Shows if the tool is connected correctly.
- Screenshot: Captures the current screen.
- Back: Returns to the previous screen.
5.3 Changing the System Language
The tool supports multiple system languages. To change the tool's language, please do the following:
- On the home screen, tap Settings -> System -> Language & Input -> Languages.
- Tap Add a language and then choose the desired language from the list.
- Tap and hold the desired language and drag it to the top of the screen, then release it, and the system will switch to the target language.
5.4 Adjusting Brightness
Note: It is useful to reduce screen brightness to conserve battery power.
- On the home screen, tap Settings -> Display -> Brightness Level.
- Drag the slider to adjust.
5.5 Setting Sleep Time
If no activity is performed within the defined waiting period, the screen will automatically lock, and the system will enter sleep mode to save power.
- On the home screen, tap Settings -> Display -> Advanced -> Sleep.
- Choose the desired sleep time.
5.6 Network Configuration
The tablet has built-in Wi-Fi that can be used to connect to the Internet. Once connected, you can register your tool, browse the Internet, and check for software updates, etc.
- On the home screen, tap Settings -> Network & Internet -> WLAN.
- Slide the Wi-Fi switch to ON; the tablet will start searching for available wireless networks.
- Select a wireless network.
- If the chosen network is open, the tablet will connect automatically.
- If the selected network is encrypted, you will need to enter a network password.
- When 'Connected' appears, it indicates that the Wi-Fi connection is complete.
Note: When Wi-Fi is not required, it should be turned off to conserve battery power.
6. First Steps: Registration and Update
For new users, a user registration process is required before starting.
6.1 Registration and Update
Follow the steps below to proceed with registration and update:
- Tap the application icon on the home screen to launch it, then tap Login to enter the diagnostic software login interface.
- If you are a new user, tap New Registration to enter the registration page. Fill in the information in each field (items with * are required). After entering the data, tap Register.
- Enter the 12-digit Product Serial Number and the 8-digit Activation Code (found on the password envelope), then tap Activate.
- Tap OK to go to the update center to update all software.
Note: The tablet has an automatic save function. Once the username and password are correctly entered, the system will save them automatically. The next time you log in to the system, you will not be asked to enter the account manually.
6.2 Work Menu Overview
The work menu includes the following main items:
| Name | Description |
|---|---|
| Intelligent Diagnosis | Obtain vehicle data from the cloud server for quick testing via VIN reading, avoiding various defects resulting from step-by-step menu selection. Check historical repair records online. |
| Local Diagnosis | Diagnose a vehicle manually. |
| Service Functions | Offers coding, reset, relearn, and other service functions to help vehicles return to functional status after repair or replacement. |
| Remote Diagnosis | Helps repair shops or technicians launch instant messages and remote diagnostics, speeding up repair work. |
| TPMS | Configures this tool as a professional TPMS service tool. Requires compatible TSGUN device (sold separately). |
| Software Update | Updates vehicle diagnostic software and APK. |
| Diagnostic History | Access diagnostic reports of previously tested vehicles. Resume previous operation without starting from scratch. |
| Feedback | Feedback the last 20 diagnostic records for problem analysis. |
| ADAS | Performs ADAS calibration operations. Requires specific ADAS calibration tool (sold separately). |
| Mall | Subscribe to additional software or service functions not included in the online diagnostic tool. |
| Vehicle Coverage | View all vehicle models covered by the tool. |
| Information Center | Includes product information and abundant maintenance data. |
| User Information | Manages VCI, reports, password changes, Wi-Fi printer settings, system settings, and logout, etc. |
| Other Modules | Includes additional modules, product manual, FAQs, and Android system applications, etc. |
7. Vehicle Connections
- Turn off the vehicle ignition.
- Ensure the vehicle battery voltage range is 11-14 volts.
- Locate the DLC (Data Link Connector). The DLC is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary. Refer to the figure below for common locations.

- A. Opel, Volkswagen, Audi
- B. Honda
- C. Volkswagen
- D. Opel, Volkswagen, Citroen
- E. Changan
- F. Hyundai, Daewoo, Kia, Honda, Toyota, Nissan, Mitsubishi, Renault, Opel, BMW, Mercedes-Benz, Mazda, Volkswagen, Audi, GM, Chrysler, Peugeot, Regal, Beijing Jeep, Citroen and other popular models.
If the DLC cannot be found, consult the vehicle service manual for its location.
- Connect one end of the included diagnostic cable to the DB-15 diagnostic connector, and the other end to the vehicle's OBD II DLC port.

8. Diagnosis
8.1 Intelligent Diagnosis
After correctly connecting the tool to the vehicle, the system will automatically decode the VIN (Vehicle Identification Number) information that currently identifies the vehicle. Once the VIN is successfully identified, the system will retrieve it from the remote server and guide you to the vehicle information page without the need for manual step-by-step menu selection.
The vehicle information page lists all historical diagnostic records for the vehicle, allowing the technician to have full command of vehicle faults. In addition, a quick dial for local diagnosis and the diagnostic function are also available on this page to reduce round trip time and increase productivity.
Notes:
- Before using this function, ensure the tool is correctly connected to the vehicle's DLC.
- A stable network connection is required for this function.
- Tap Intelligent Diagnosis on the Work menu screen to start pairing.
- Once pairing is complete, the tablet begins to read the vehicle's VIN.
- If the VIN can be found in the remote server database, the system will proceed to the diagnostic function selection screen. If the tablet could not access the VIN information, you will be prompted to enter it manually or use the VIN recognition module.
8.2 Local Diagnosis
In this mode, you must execute the menu-driven command and then follow the on-screen instructions to proceed.
Tap Local Diagnosis to enter the vehicle selection page.

Function Buttons:
- VIN Scan: Automatically decodes the vehicle's VIN and starts diagnosis.
- All: Tap to view all vehicle models covered by the tablet.
- Common: Tap to create a list of commonly used diagnostic software or remove certain software from the list.
- American/European/Asian/Chinese: Display only American/Asian/Chinese vehicle brands.
- Purchase: Quick access to the online Mall to buy other software and renew subscriptions.
- DEMO: A simulation program for training purposes only.
- EOBD/OBDII: A simple and quick diagnostic program that checks I/M readiness and OBDII information.
- AUDI and other brands: Enhanced diagnostic program with manufacturer-specific information.
There are two approaches to access vehicle diagnostic software:
- VIN Scan: Allows faster access. Tap VIN Scan; camera scanning and VIN entry are available. If the tablet successfully identifies the vehicle model, it will directly enter the diagnostic function selection menu.
- Tap the corresponding diagnostic software logo and follow the on-screen instructions to access the diagnostic software.
8.2.1 Health Report (Quick Test)
This function varies from vehicle to vehicle. It allows you to quickly access all electronic control units of the vehicle and generate a detailed report on the vehicle's status. On the test item selection screen, tap Health Report and turn on the ignition switch; the system will start scanning the ECUs. Once the scanning process is complete, the results will be displayed.
Warning: Diagnostic Trouble Codes (DTCs) or Fault Codes can be used to identify which engine systems or components are malfunctioning. Never replace a part based solely on the DTC definition. The retrieval and use of DTCs to troubleshoot vehicle malfunctions is only part of a general diagnostic strategy. Follow the test procedures (in the vehicle service manual), instructions, and flowcharts to confirm problem locations.
On-screen Buttons:
- Enter: Tap to enter the diagnostic function selection screen.
- Search: Highlight a specific diagnostic trouble code and tap it to retrieve it in the search engine.
- Report: Tap to save the diagnostic result as a health report.
8.2.2 Clear DTCs
This function allows you to clear vehicle codes after reading the retrieved vehicle codes and performing certain repairs. Before performing this function, ensure the vehicle's ignition key is in the ON position with the engine off.
Note: Clearing DTCs does not solve the problem that caused the codes to be set. If proper repairs are not made to correct the problem that caused the codes, the codes will reappear, and the check engine light will illuminate as soon as the problem that caused it manifests itself.
8.2.3 System Scan
This option allows you to quickly scan which systems are installed in the vehicle.
8.2.4 System Selection
This option allows you to manually select the test system and the step-by-step function. On the test item selection screen, tap System Selection.
8.2.5 Read Data Stream
This option allows you to view and capture (record) live data in real-time. This data, which includes the current operating status of parameters and/or sensor information, can provide information about the overall vehicle performance. It can also be used to guide vehicle repair.
Caution: If you must drive the vehicle to perform a troubleshooting procedure, always ask a second person for help. Attempting to drive and operate the diagnostic tool at the same time is dangerous and could cause a serious traffic accident.
Note: Real-time vehicle operating information (live data) (values/status) that the on-board computer provides to the tool for each sensor, actuator, switch, etc. is called Parameter Identification Data (PID).
On the diagnostic function selection screen, tap Read Data Stream.
On-screen Buttons:
- Select Page: Tap to select all items on the current page.
- Select All: Tap to select all items. To select a specific data stream item, just check the box next to the item name.
- Deselect: Tap to deselect all data stream items.
- OK: Tap to confirm and proceed to the next step.
After selecting the desired items, tap OK to enter the data stream reading page.
There are 3 types of display modes available for data viewing:
- Value: This is the default mode that displays parameters in text and in list format.
- Graph: Displays parameters in waveform graphs.
- Combine: This option is mainly used in the graph combination state for data comparison. In this case, different items are marked in different colors (up to 4 items can be displayed simultaneously on the same screen).
On-screen Buttons (Data Stream Display):
- Graph (Single): Tap to view the parameter in waveform graph.
- Combine: This option is mainly used in the graph combination state for data comparison. In this case, different items are marked in different colors (up to 4 items can be displayed simultaneously on the same screen). If the graph has more than one page, swipe the screen from left to right to go to the next page.
- Value: Changes the current graph display mode to value display mode.
- Customize: Tap, a dropdown list of data stream items appears on the screen. Select/deselect the desired items, and the screen will immediately display/remove the corresponding waveforms for these items.
- Compare Samples: Tap to select the sample DS file. All values you customized and saved during the DS sampling process will be imported into the Standard Range column for comparison.
- Report: Tap to save the current data in text format.
- Record: Tap to start recording diagnostic data. Recorded live data can serve as valuable information to help in vehicle troubleshooting.
8.2.6 Actuation Test
This option is used to access subsystem and vehicle-specific component tests. Available tests vary by manufacturer, year, and vehicle model.
During the actuation test, the display tablet sends commands to the ECU to actuate the actuators, and then determines the integrity of the system or parts by reading the ECU data, or monitoring the operation of the actuators, such as switching an injector between two operating states.
8.3 Remote Diagnosis
This module helps repair shops or mechanics diagnose a remote vehicle and launch instant messages, which improves efficiency and speeds up repairs.
Tap Remote Diagnosis on the Work menu; the screen appears blank by default.
Remote Diagnosis Interface:
- Home Button: Go to the Work menu screen.
- Search Bar: Directly enter the tool's username for searching, then tap the one you want to add to the Contacts list.
- Messages Tab: A red dot will appear indicating a received message.
- Contacts Tab: Enter the friends list.
- Remote Switch: Your technician can remotely control your tool once the switch is On.
8.3.1 Add Friends
Tap Contacts. By default, it appears blank. In the search bar, enter the partner's username and tap Search to start the search. The partner must be a user who has registered specific diagnostic tools. These can be: Workshop, Technician, Golo users.
Once the result matches the keyword, tap Add Friends to send your request. Once the partner receives the request, a beep will sound. Tap Messages. Once the partner receives the request, it will automatically appear in the Contacts tab. If a technician has sent you a friend request, tap Accept and their name will appear in the Contacts list. Or tap Ignore to ignore this request.
8.3.2 Start Instant Messaging
The I/M (Instant Messaging) function is open to all users who had the diagnostic tool equipped with this module. After adding your friends, tap the desired photo to enter the following screen:
Tap the input field and use the on-screen keyboard to send the text message. Tap the microphone icon to send a voice message. Tap the emoji icon to send an emoji. Tap the plus icon to call up more function options.
Function Options:
- File: Choose diagnostic reports or local files to send.
- Picture: Choose screenshots or images to send.
- Remote Diagnosis: To start a remote diagnostic session. For more details, see Section 8.3.3.
- Camera: Opens the camera to take photos.
8.3.3 Start Remote Diagnosis (Device to Device)
The tool allows starting remote diagnosis with other diagnostic tools that are equipped with this module. On the function options selection screen, tap Remote Diagnosis; the following dropdown menu will appear:
- Request Control Remote Device: Request remote control of the partner's device to help diagnose the vehicle.
- Invite Remote Diagnose Assistant: Use this option to invite a technician to perform a remote control on your tool.
- Cancel: To cancel this operation.
8.3.4 Start Remote Diagnosis (Device to PC)
The user can also request remote control from a PC client technician. Tap Remote; the following screen will appear:
- Slide the switch to ON so that the partner can find and connect to this device while using the PC.
- Notify the partner of the PC client website http://remote.x431.com. When the partner accesses the link, the PC will display a login screen.
- Tell the partner to enter their official technician account and password, and then tap Login.
- Tell the partner to enter the Serial Number you provided, and then tap Start remote diagnosis to control your device remotely.
Note: Before processing remote diagnosis, ensure the tool is correctly connected to the vehicle.
During the remote diagnosis process, keep the following in mind:
- You are not suggested to perform any actions.
- The partner cannot save any diagnostic reports or records on your tablet.
Once the session is finished, a remote diagnostic report will be automatically generated.
9. Service Functions (Reset)
The tool offers coding, reset, relearn, and other service functions to help vehicles return to functional status after repair or replacement. Available tests vary by vehicle manufacturer, year, and model.
Due to continuous improvements, available service functions are subject to change at any time. To enjoy more service functions, it is suggested to check for updates regularly.

9.1 Oil Maintenance Light Reset (Oil Reset)
This function allows you to reset the oil service light for the engine oil life system, which calculates an optimal oil life change interval based on vehicle driving conditions and weather phenomena.
This should be done in the following cases:
- If the service light is on, first perform vehicle diagnosis to solve the problem. After that, reset the mileage or driving time to turn off the service light and enable a new driving cycle.
- If the service light is not on, but the engine oil or electrical devices controlling the oil life have been changed, the service light must be reset.
9.2 Electronic Parking Brake Reset (BRAKE RESET)
This function allows you to reset the brake pad after replacing the brake pad.
This should be done in the following cases:
- The brake pad and brake pad wear sensor are replaced.
- The brake pad indicator light is on.
- The brake pad sensor circuit is short-circuited and recovers.
- The servomotor is replaced.
9.3 Steering Angle Reset (SAS Reset)
This function allows you to readjust the steering angle after replacing the steering angle position sensor, replacing mechanical steering parts (such as the steering gearbox, steering column, tie rod end, steering knuckle), performing four-wheel alignment, or recovering the car body.
To readjust the steering angle, first find the relative zero point position for the car to drive straight. Taking this position as a reference, the ECU can calculate the exact angle for left and right steering.
9.4 ABS Bleeding
This function allows you to perform various bi-directional tests to check the operating conditions of the Anti-lock Braking System (ABS).
This should be done in the following cases:
- When the ABS contains air.
- When the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced.
9.5 Crankshaft Position Sensor Adaptive Learning (GEAR LEARN)
This function can perform gear learning for the car to turn off the related Malfunction Indicator Light (MIL).
This should be done in the following cases:
- After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced.
- The DTC "tooth not learned" is present.
9.6 Anti-theft Matching (IMMO)
This function can match the anti-theft key after replacing the ignition key, ignition switch, instrument panel, engine control unit (ECU), body control module (BCM), and remote control battery.
9.7 Injector Coding (INJECTOR)
This function allows you to write the actual injector code or rewrite the code in the ECU to the corresponding cylinder injector code, to more precisely control or correct the amount of cylinder injection.
This should be done in the following cases:
- After replacing the ECU or injector.
9.8 Battery Matching (BATTERY RESET)
This function allows you to perform a reset operation on the vehicle's battery monitoring unit, in which original low battery fault information will be cleared and battery matching will be performed.
This should be done in the following cases:
- The main battery is replaced.
- The battery monitoring sensor is replaced.
9.9 DPF Regeneration (DPF REG.)
This function allows you to remove PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high-temperature heating combustion, fuel additive, or catalyst reduce PM ignition combustion) to stabilize filter performance.
This should be done in the following cases:
- The exhaust back pressure sensor is replaced.
- The PM trap is removed or replaced.
- The fuel additive nozzle is removed or replaced.
- The catalytic oxidant is removed or replaced.
- MIL regeneration is activated, and maintenance is performed.
- The DPF regeneration control module is replaced.
9.10 Accelerator Matching (ELECTRONIC THROTTLE RELEARN)
This function allows you to perform initial adjustments to accelerate the actuators and return the learned values stored in the ECU to the default state. Doing so can precisely control the accelerator regulation actions (or idle speed motor) to adjust the air intake amount.
9.11 Gearbox Matching (GEARBOX)
This function allows you to complete gearbox self-learning to improve gear shift quality.
This should be done in the following cases:
- When the gearbox is disassembled or repaired.
9.12 Headlight Matching (AFS RESET)
This function allows you to initialize the adaptive headlight system.
9.13 Sunroof Initialization (SUNROOF)
This function allows you to disable sunroof lock, close it when it rains, slide/tilt sunroof memory function, outside car temperature threshold, etc.
9.14 Suspension Level Calibration (SUS RESET)
This function allows you to adjust the body height.
This should be done in the following cases:
- When replacing the body height sensor or control module in the air suspension system.
- When the vehicle height is incorrect.
9.15 EGR Adaptation
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after cleaning or replacing it.
9.16 Seat Calibration
This function applies to matching memory seats that are replaced and repaired.
9.17 Tire Reset
This function is used to set the size parameters of modified or replaced tires.
9.18 Coolant Bleeding
Use this function to activate the electronic water pump before venting the cooling system.
9.19 AdBlue Reset
After replacing or filling the diesel exhaust fluid (automotive urea), a urea reset operation is required.
9.20 NOx Sensor Reset
The NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in the engine exhaust. If the NOx fault is reset and the NOx catalytic converter is replaced, the learned value of the catalytic converter stored in the engine ECU must be reset.
9.21 AC System Relearn/Initialization
AC system relearn/initialization must be performed when the AC ECU or vehicle actuator is replaced or the ECU memory is lost.
9.22 High Voltage Battery Detection (HIGH VOLTAGE BATTERY)
This function is used for high voltage battery diagnosis and status information detection.
9.23 Window Calibration
This function is used to perform door window matching to recover the initial memory of the ECU and recover the automatic up and down function of the power window.
9.24 Language Change
This function is used to change the system language of the vehicle's central console.
9.25 A/F Reset
This function applies to setting or learning air/fuel ratio parameters.
9.26 Transport Mode
To reduce vehicle power consumption, the user can perform the following operations: limit vehicle speed, not activate the network to open the door, and deactivate the remote key, etc. In this case, it is necessary to deactivate transport mode to restore the vehicle to normal.
9.27 Start/Stop Reset
This function is used to open or close the automatic Start/Stop function by configuring the hidden function in the ECU (the prerequisite is that the vehicle is equipped with hidden function and hardware support).
9.28 Intelligent Cruise Control System Reset
This function is used to match the intelligent cruise control module after it is replaced or repaired.
9.29 Engine Power Balance Monitoring
This function is used to monitor crankshaft acceleration in each cylinder's power stroke to determine the relative power provided by each cylinder.
9.30 Gas Particulate Filter Regeneration (GPF)
This function is used to perform GPF replacement or regeneration after fuel consumption increases and engine output power decreases as a result of prolonged GPF service.
9.31 Engine Angle Calibration
This function is used to perform engine angle calibration when the rotor position detected by the engine angle position sensor is different from the actual rotor field position.
10. Other Modules
Each module consists of two parts: hardware and application. These modules cannot function correctly on the tablet alone; they must work with specific compatible hardware.

10.1 Tool Box
10.1.1 ADAS (Calibration)
This module allows you to effectively and accurately calibrate a wide range of camera and radar-based driver assistance systems, e.g., the front camera for the lane departure warning system, the radar sensor for ACC (Adaptive Cruise Control), or the camera for adaptive headlights. It must work with the specific ADAS calibration tool (sold separately). For more details, consult the User Manual included with the module.
10.1.2 TPMS
This module allows you to configure the tablet as a TPMS activation and diagnostic tool, providing the ability to activate the TPMS sensor, program the TPMS sensor, and perform the relearn procedure. It must work with the compatible TSGUN device (sold separately). For more details, consult the User Manual included with the module.
10.1.3 Oscilloscope
This module can help automotive repair technicians quickly diagnose faults in electronic equipment and vehicle wiring. For more details, consult the User Manual included with the module.
10.1.4 BST360 (Battery Tester)
This module allows you to perform battery detection faster and easier. It must work with the specific Bluetooth battery tester (sold separately).
10.1.5 S2-2 Sensorbox
This module is specially designed to diagnose and simulate vehicle sensor faults quickly and conveniently. It must work with the compatible S2-2 Sensorbox (sold separately). For more details, consult the User Manual included with the module.
10.1.6 S2-2 Multimeter
This module allows you to measure physical parameters such as voltage, resistance, frequency, etc. It uses the same hardware as the S2-2 Sensorbox. For more information, consult the User Manual included with the S2-2 Sensorbox.
10.1.7 Immobilizer Programmer
This module allows you to perform read-write functions for vehicle keys, EEPROM, MCU, and EEPROM/FLASH of the vehicle engine and gearbox ECU. It must work with the specific immobilizer programmer (sold separately). For more details, consult the User Manual included with the module.
10.1.8 Videoscope
This module allows you to check invisible parts of the engine, fuel tank, and braking system. It must work with the compatible Videoscope device (sold separately). For more details, consult the User Manual included with the module.
10.2 Vehicle Coverage
This module allows you to check which vehicle models the tool covers.
10.3 Android System Applications
10.3.1 Recording Master
This module is a free and convenient application that allows you to take high-quality tablet screen video captures, with or without sound.
10.3.2 Browser
This browser is a free cross-platform web browser. It has gained popularity worldwide, with tools such as file downloads, password settings, and bookmarks. Users can load multiple web pages or use a search engine to find any topic on the Internet.
10.3.3 Camera
This application allows you to take photos or record videos with the device's camera.
10.3.4 Gallery
This function allows you to take new photos and manage the image library (including screenshots).
10.3.5 Calculator
It is an easy-to-use and responsive application. All calculations are performed on the fly as you enter new data.
10.3.6 Files
This module is a very useful file and application manager, task killer, and download manager.
10.3.7 Tablet Settings
This module provides quick access to Android system settings.
11. Software Update
This module allows you to update the diagnostic software and application, and frequently used software.
11.1 Updating Diagnostic Software and Application
Go to Software Update on the home screen and tap the Downloaded tab.
The Available tab shows a list of software that can be updated. All software is classified into three types:
- Common software: Mainly includes some common applications associated with the diagnostic application. This type of software is always kept at the top of the list, which can be manually deselected (excluding system applications, such as firmware and ECU help).
- Frequently used vehicle software: Refers to diagnostic software that is frequently used, including vehicle diagnostic software and Reset software. It is usually displayed after the Common software list.
- Other vehicle software: Refers to diagnostic software that is rarely or never used. It is usually displayed after the Frequently used software list.
- If the user does not download any diagnostic software during the registration process, all diagnostic software is selected by default. Tap Update to start the download.
- If the user downloaded all/part of the vehicle software during the registration process and reviewed it for a long time, only frequently used software is selected. Tap Update to start the download. Other vehicle software that is rarely used will also appear on the Available tab, but is not selected by default.
To download certain software that is not frequently used, check the box next to the vehicle model. Tap Update to start the download. Once the download is complete, the software packages will be installed automatically.
11.2 Updating Frequently Used Software
If the user only intends to update frequently used software, go to Software Update and tap the Downloaded tab.
Tap Update to start the download. Once the download is complete, the software packages will be installed automatically.
11.3 Renewing Subscription
If the software subscription expires, the system will ask you to renew your subscription.
Tap Renewals to open the Mall, then follow the on-screen instructions to complete the subscription.
12. User Information
This function allows users to manage personal information.
12.1 My Report
This option is used to view, delete, or share saved reports. Tap Report; there are a total of 3 options available.
If the DTC result is saved on the Read Trouble Code page, the files will be listed under the Health Reports tab.
If the user records running parameters while reading the data stream, the tablet will save the file that appears under the Recorded Data tab.
Remote Reports lists all diagnostic reports generated during the remote diagnosis process.
12.2 VCI
This option allows you to review all active VCI devices.
12.3 Activate VCI
This item allows you to activate the VCI device if you skipped the Activate VCI step during product registration.
12.4 Firmware Correction
Use this item to update and correct diagnostic firmware. During repair, do not cut power or switch to other interfaces.
12.5 Sample
This feature allows you to manage recorded data stream sample files.
12.6 My Order
This item allows you to check the status of all your orders.
12.7 Subscription Renewal Card
This item is used to check the status of the subscription renewal card. Enter the 12-digit subscription renewal card number. Tap Search to get the search result.
12.8 Profile
Use this item to view and configure personal information.
12.9 Change Password
This item allows you to modify your login password.
12.10 Settings
Allows you to make some application settings and view software version information, etc.
12.10.1 Units
It is designed to configure the unit of measurement. Metric and English systems are available.
12.10.2 Store Information
This option allows you to define your store information. It mainly includes Workshop, Address, Phone, Fax, and License Plate. After entering, tap Save. Once the store information is saved, it will be automatically entered into the Add information box each time you save the diagnostic report.
12.10.3 Printer Settings
This option is designed to establish a wireless connection between the tablet and the Wi-Fi printer (sold separately) while performing printing operations.
The Application is compatible with the LAUNCH Wi-Fi Printer (sold separately) and the System (external printer).
For the LAUNCH Wi-Fi printer, consult the user manual included with the printer.
For other Wi-Fi printers, before printing, ensure the following conditions are met:
- The Wi-Fi printer is on and working normally.
- The print service plugin associated with the printer is already installed on the tablet (use the browser to download and install it).
Follow these steps to continue:
- Set the default printer to System.
- Go to Other Modules -> Tablet Settings -> WLAN, set the WLAN switch to Off.
- On the report details page, tap the printer icon next to Select a printer in the upper left corner of the screen.
- Select All Printers -> Add Printer and enable the installed printer service; the system will start searching for all available Wi-Fi printers of the brand.
- Select the desired Wi-Fi printer from the list. If the access point of the chosen Wi-Fi printer is open, the tablet can connect directly. If it is encrypted, a password may be required. Consult the Wi-Fi printer user manual for the default password.
- Now the printer is ready to print.
- Alternatively, you can also choose Save as PDF to save the current diagnostic report as a PDF file for later printing.
12.10.4 Clear Cache
This option allows you to clear the Application cache. Clearing the cache will restart the Application.
12.10.5 About
Includes software version information and disclaimer.
12.10.6 Automatic Diagnostic Software Update
This option is used to set whether the automatic update function is activated.
12.10.7 Device Account Management
This option is used to manage sub-accounts. Added sub-accounts allow different users to use the tool to facilitate tracking diagnostic records of different technicians.
12.10.8 Login/Logout
To log out of the current user ID, tap Logout. To log back into the system, tap Login.
12.10.9 Delete Diagnostic Software
This item allows you to hide/delete diagnostic software that is not frequently used.
Note: Deleting software can completely erase the software from the tablet. If some software is not used and the tablet runs out of space, you can use this function to delete it.
13. User Tips
- For optimal performance, keep your device's software updated regularly.
- Ensure a stable Wi-Fi connection for seamless updates and remote diagnostic sessions.
- Always refer to your vehicle's service manual for specific diagnostic procedures and DTC troubleshooting.
14. Frequently Asked Questions (FAQ)
14.1 How to save power?
- Please turn off the screen while the tool remains inactive.
- Set a shorter sleep time.
- Reduce screen brightness.
- If WLAN connection is not required, please turn it off.
- Disable the GPS function if GPS service is not in use.
14.2 Communication error with the vehicle ECU?
Please confirm:
- If the tool connection is correct.
- If the ignition switch is ON.
- If all checks are normal, send us the year, make, model, and VIN of the vehicle using the Feedback function.
14.3 Error entering the vehicle ECU system?
Please confirm:
- If the vehicle is equipped with this system.
- If the tool connection is correct.
- If the ignition switch is ON.
- If all checks are normal, send us the year, make, model, and VIN of the vehicle using the Feedback function.
14.4 How to download the diagnostic application after restarting the tablet?
Note: Before registration, ensure the network is correctly connected.
After the tablet has successfully restarted, follow these steps to download the Application:
- Launch the browser, and the official Launch default website will open (If a blank page appears, simply type www.x431.com in the address bar).
- Tap Login, enter your username and password, and tap Login.
- Ensure the serial number is correct, tap APP application program, and tap the Download icon to start downloading.
- Once the download is complete, follow the on-screen instructions to install it.
- After installation, use your existing username and password to log in and go to the update center to download the diagnostic software.
14.5 What to do if the vehicle diagnostic software language does not match the system language?
English is the default system language of the tool. After setting the system language to your preferred language, go to the update center to download the vehicle diagnostic software in the corresponding language.
If the downloaded diagnostic software is still displayed in English, it indicates that the current language software is under development.
14.6 How to recover the login password?
Please follow these steps to proceed if you have forgotten your login password:
- Tap the application icon on the home screen to launch it.
- Tap Login in the upper right corner of the screen.
- Tap Recover Password.
15. Specifications
| Attribute | Value |
|---|---|
| Operating System | Android 10.0 |
| Processor | Quad core 2.0GHz |
| RAM/ROM | 4GB/64GB |
| Display | 8 inches, LCD touchscreen |
| Display Resolution | 1280x800 |
| Camera | Rear 8.0MP |
| Connectivity | WIFI (5G/2.4GHz), USB (Type-A x 1, Type-C x 1) |
| Battery | 6000mAh |
| Product Dimensions | 10.1"L x 1.6"W x 6.7"H (256*171*40.5 mm) |
| Item Weight | 8.8 pounds (1000g net weight) |
| Working Temperature | 0℃~50℃ |
| Storage Temperature | -20°C to 70°C |
| External Testing Certification | CCC |
| Origin | Mainland China |
| Free Update | 2 Years Free Update |
| Warranty | 5 Year |
16. Warranty and Support
16.1 Warranty
This warranty is expressly limited to persons who purchase LAUNCH® products for resale or use in the ordinary course of the buyer's business.
The LAUNCH® electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than that for which it was designed, or used in a manner inconsistent with the instructions for use. The exclusive remedy for any defective automotive meter is repair or replacement, and LAUNCH will not be responsible for any consequential or incidental damage.
The final determination of defects will be made by LAUNCH in accordance with stipulated procedures.
16.2 Customer Service
If you have any questions about the operation of the unit, please contact the distributor or customer service center:
- Tel: 86-755-25938674
- E-mail: DOD@cnlaunch.com
16.3 Disclaimer
LAUNCH reserves the right to make any changes to the designs and specifications of the product without prior notice. The actual object may differ slightly from the descriptions in the manual in terms of physical appearance, color, and configuration. We have made every effort to ensure that the descriptions and illustrations in the manual are as accurate as possible, and defects are inevitable. If you have any questions, please contact the local distributor or after-sales service center. LAUNCH assumes no responsibility for misunderstandings arising from this.