1. Safety Information
Important Safety Precautions
To avoid personal injury, property damage, or accidental damage to the product, read all of the information in this section before using the tool.
DANGER
- When an engine is operating, keep the service area well-ventilated or attach a building exhaust removal system to the engine exhaust system. Engines produce various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen oxides, etc.) that slow reaction time and result in death or serious personal injury.
- Please use the included battery and power adaptor. There is a risk of explosion for using batteries that are not authorized or approved by the manufacturer.
- DO NOT attempt to operate the tool while driving the vehicle. Have a second person operate the tool. Any distraction may cause an accident.
WARNING
- Always perform automotive testing in a safe environment.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- NEVER smoke or allow a spark or flame in the vicinity of the battery or engine. Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or heavy dust.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Wear an ANSI-approved eye shield when testing or repairing vehicles.
- Chock drive wheels and never leave the vehicle unattended while testing.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltage when the engine is running.
- To avoid damaging the tool or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle Data Link Connector (DLC) is clear and secure.
- Retrieving and using Diagnostic Trouble Codes (DTCs) for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Never replace a part based only on the DTC definition. Each DTC has a set of testing procedures, instructions and flow charts that must be followed to confirm the location of the problem. This information can be found in the vehicle's service manual.
- Automotive batteries contain sulfuric acid that is harmful to skin. In operation, direct contact with the automotive batteries should be avoided. Keep the ignition sources away from the battery at all times.
- Keep the tool dry, clean, and free of oil, water, or grease. Use a mild detergent on a clean cloth to clear the enclosure of the equipment when necessary.
- Keep clothing, hair, hands, tools, test equipment, and other objects away from all moving or hot engine parts.
- Store the tool and accessories in a locked area and out of reach of children.
- Do not use the tool while standing in water.
- Do not expose the tool or power adapter to rain or wet conditions. Water entering the tool or power adaptor increases the risk of electric shock.
- Do not keep using the scan tool when it is being charged.
- This tool is a sealed unit. There are no end-user serviceable parts inside. All internal repairs must be done by an authorized repair facility or qualified technician. If there is any inquiry, please contact the dealer.
- Keep the tool far away from magnetic devices because its radiations can damage the screen and erase the data stored on the tool.
- Do not attempt to replace the internal rechargeable lithium battery. Contact the dealer for factory replacement.
- Do not disconnect battery or any wiring cables in the vehicle when the ignition switch is on, as this could result in damage to the sensors or the Electronic Control Unit (ECU).
- Do not place any magnetic objects near the ECU. Disconnect the power supply to the ECU before performing any welding operations on the vehicle.
- Use extreme caution when performing any operations near the ECU or sensors. Ground yourself when you disassemble Programmable Read Only Memory (PROM). Otherwise, ECU and sensors can be damaged by static electricity.
- When reconnecting the ECU harness connector, be sure it is attached firmly. Otherwise, electronic elements, such as Integrated Circuits (ICs) inside the ECU, can be damaged.
Compliance Information
FCC ID: XUJWO0805A
IC: 29886-WO0805A
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Innovation, Science and Economic Development Canada's licence-exempt RSSs and part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference; and
- This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme aux RSSs exempts de licence d' Innovation, Sciences et Développement économique Canada et à la partie 15 des règles de la FCC. Le fonctionnement est soumis aux deux conditions suivantes:
Specific Absorption Rate (SAR) information
This product meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
RF Exposure Information and Statement
The SAR limit is 1.6 W/kg averaged over one gram of tissue. This device has also been tested against this SAR limit. This device was tested for typical body-worn operations 0mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm separation distance between the user's body.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user's body, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
This device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The RF frequencies can be used in Europe without restriction.
2. Overview
2.1 Packing List
The following packing list is for reference purpose only. For different destinations, the accessories may vary. For details, please consult the seller or check the packing list supplied with this tool together.
- Scan tool x 1
- Diagnostic cable x 1
- Power adaptor x 1 (including 2 switching adaptors)
- Password envelope x 1
- Type-A to Type-C data cable x 1
- Multilingual quick start guide x 1
- User manual x 1
2.2 Components & Controls
- Type-C USB Port: Connects to AC outlet for charging and to PC for data exchange.
- Type-A USB Port: Connect to compatible add-on modules (such as Videoscope) or USB storage devices.
- DB-15 Diagnostic Connector: Connect the diagnostic cable.
- POWER Button: Turn the scan tool on/off. Press and hold for 8 seconds for forced shutdown.
- Charging LED: Red indicates Charging; Green indicates Fully Charged.
- LCD Screen: Indicates the test result.
- Camera flash
- Adjustable stand: Flips out to any angle for comfortable use or hanging on the steering wheel.
- Rear camera
- Speakers
3. Getting Started
3.1 Charging & Turning On
- Use the included power adaptor to charge the scan tool.
- After charging is complete, press the POWER button to turn the scan tool on. The system starts initializing and then enters the home screen.
Note: If the battery remains unused for a long period of time or the battery is completely discharged, it is normal that the tool will not power on while being charged. Charge the tool for 5 minutes and then turn it on.
Warning: Only use the included power adaptor to charge your tool. LAUNCH assumes no responsibility for damage or loss resulting from using other similar adaptors other than the specified one.
To turn off the tool, press and hold the POWER button until an option menu appears. Tap Power Off.
3.2 Screen Layout
There are five on-screen buttons available on the bottom of the screen:
- Home: Navigates to the home screen.
- Recent App: Views the currently running or recently used applications.
- Connection Status: Shows whether the tool is properly connected or not.
- Screenshot: Captures the current screen.
- Back: Returns to the previous screen.
3.3 Language Setting
The tool supports multiple system languages. To change the language of the tool, please do the following:
- On the home screen, tap Settings -> System -> Languages & input -> Languages.
- Tap Add a language, and then choose the desired language from the list.
- Tap and hold the desired language and drag it to the top of the screen and then release it, the system will change into the target language.
3.4 Network Setup
The built-in Wi-Fi module in the tool makes network connection easier. Once you're online, you can register your tool, surf the Internet, send email, launch the remote diagnosis, and check for software updates, etc.
- On the home screen, tap Settings -> Network & Internet -> Wi-Fi.
- Slide the Wi-Fi switch to ON, and the scan tool starts searching for available wireless networks.
- Select a wireless network:
- If the selected network is open, the scan tool will connect to the network automatically.
- If the selected network is encrypted, the right security key (network password) is required.
- When Connected appears, it indicates the Wi-Fi connection is complete.
Note: Power consumption of the tool increases when the Wi-Fi is always on. To save power, turn off the Wi-Fi if network is not required.
3.5 Registration & Update
For new users, register first before you get started. Follow the steps below to proceed registration and update:
- Tap the application icon on the home screen to open it, and then tap Login on the upper right corner of the screen.
- If you have not registered any authorized account of LAUNCH scan tool, please use Email login. Tap New Registration. Input the Email address, tap CAPTCHA and enter the received verification code. Tap Login-Register to continue.
- If no scan tools are bound to this Email before, follow the steps below to proceed:
- After the popup appears, tap ACTIVATE VCI to go to the next step.
- Input the 12-digit Product Serial Number and 8-digit Activation Code (can be obtained from the password envelope), and then tap ACTIVATE.
- After the VCI device is successfully activated, the system automatically enters the update center. Tap Update to update all available software.
- If there are scan tools bound to this Email, it will enter the job menu screen directly. In this case:
- Tap the button on the upper right corner to enter User Info.
- Tap Activate VCI. Input the Product Serial Number and Activation Code, and then tap Activate.
- Go to Software Update to update all available software.
- If no scan tools are bound to this Email before, follow the steps below to proceed:
- If you have an authorized account of LAUNCH scan tool, please use Password login. Input the username and password (If you forgot the password, tap Set/Reset Password to set a new one), and tap Login to login the diagnostic system.
Note: All software is updated periodically. It is recommended to check regularly for updates and install the latest software for the best service, functions and experience.
3.6 Job Menu Overview
The job menu mainly includes the following function modules:
| Name | Description |
|---|---|
| Intelligent Diagnose | Obtain vehicle data from the cloud server to perform quick test via reading VIN, to avoid various defects resulting from step-by-step menu selection. Check the historical repair records online. |
| Local Diagnose | Diagnose a vehicle manually. |
| Remote Diagnose | This option aims to help repair shops or technicians launch instant messages and remote diagnosis, making the repair job getting fixed faster. |
| Special Function | It offers coding, reset, relearn and more service functions, to help vehicles get back to functional status after repair or replacement. |
| Toolbox | Provide some additional add-on tools to extend the functions of the scan tool. |
| Software Update | To update vehicle diagnostic software and APK. |
| X-431 Diagnosis Kit | Include vehicle coverage, CANBUS pin detection, CANScope, and Fix connector firmware, etc. |
| Feedback | To feed back the recent 20 diagnostic logs to us for issue analysis. |
| Know Your Customer | Assist merchants in conducting business opportunity analysis, customer management, and diagnostic statistics. |
| Mall | Subscribe some extra software or service functions that are not included in the diagnostic tool online. |
| LAUNCH Academy | Include abundant repair case, operation skills and training videos for quick reference. |
| User Info | Manage VCI, diagnostic reports & recorded data, password, order and logout / login etc. |
| Settings | Make some system settings of diagnostic application. |
| About | Include software version, product manual, service agreement and privacy policy etc. |
4. Connections
- Make sure that the ignition is turned off and vehicle battery voltage is within 9-14V.
- Locate the vehicle's DLC. For passenger cars, the DLC is usually located 12 inches from the center of the instrument panel, under or around the driver's side for most vehicles. For some vehicles with special designs, the DLC location may vary.
- For OBDII vehicles, use the included diagnostic cable to connect the scan tool to the DLC port of the vehicle.
- Turn the ignition ON with engine OFF.
- Now the tool is ready for diagnostics.
5. Vehicle Diagnosis
5.1 Intelligent Diagnose
This function enables you to obtain vehicle data from the cloud server to perform quick test via decoding VIN, to avoid various defects resulting from step-by-step menu selection. Tap Intelligent Diagnose on the Job menu screen to start reading the vehicle VIN.
If the VIN is successfully decoded, the following options will appear:
- Tap Diagnostic to start a new diagnostic session.
- Tap Scan History to view its historical repair records.
- Tap Quick access to go directly to the function selection screen.
Note: Not all vehicles support this function due to settings imposed by auto manufacturers. A highly stable network connection is recommended for successful VIN access.
5.2 Local Diagnose
If the scan tool cannot analyze the VIN information, you can also perform Local (Manual) Diagnose. Tap Local Diagnose to enter the vehicle selection page.
Two approaches are provided to access the vehicle diagnostic software:
- Operations of VINSCAN Service are the same as Intelligent Diagnose.
- Manually select the vehicle's make, model and year. In this mode, you need to execute the menu-driven command and follow the on-screen instructions to proceed.
On-screen Buttons:
- Vehicle Coverage: Tap to view the vehicle models that the current diagnostic software covers.
- OK: Tap it to go to next step.
5.3 Health Report (Quick Test)
This function varies from vehicle to vehicle and only appears if the vehicle's model diagnosis software supports this function. You can quickly access all the electronic control units of the vehicle and get a detailed report about vehicle health.
On the test item selection screen, tap Health Report and turn on the ignition switch, the system will start scanning the ECUs. Once the scan is complete, the following screen will appear:
The system with fault codes is displayed in red. The system with no fault codes is displayed in green.
Note: Diagnostic Trouble Codes or Fault Codes can be used to identify which engine systems or components are malfunctioning. Never replace a part based only on the DTC definition. Retrieving and using DTCs for troubleshooting vehicle operation is only one part of an overall diagnostic strategy. Follow testing procedures (in vehicle's service manual), instructions and flowcharts to locate the problem.
On-screen Buttons:
- Enter: Tap to enter the diagnostic function selection screen.
- Search: Highlight a diagnostic trouble code and tap it to retrieve it in the search engine.
- Report: Tap to save the diagnostic result as a health report. All diagnostic reports are saved in User Info -> My Report -> Health Reports.
- Compare Results: Tap to select the pre-repair report to compare. By comparison of the pre- and post- repair reports, you can easily identify which DTCs are cleared and which remain unfixed.
- Clear DTCs: Tap to clear the existing diagnostic trouble codes.
5.4 System Scan
This function allows you to quickly scan which systems are installed on the vehicle.
5.5 System Selection
This function allows you to manually select the test system and perform the related diagnostic functions. On the test item selection screen, tap System Selection. Select the desired system (take ECM/PCM for example) the following screen will appear:
- Version Information: This function can read the version information of system mode, vehicle VIN, software and ECU.
- Read Fault Code: This function can read the detailed information of DTC in the ECU memory, quickly identifying the cause of the vehicle breakdown.
- Read Data Stream: This option retrieves and displays live data from the vehicle's ECU. This data including current operating status for parameters and/or sensor information can provide insight on overall vehicle performance.
- Actuation Test: This option is used to access vehicle-specific subsystem and component tests. Available tests vary by vehicle manufacturer, year, and model.
- Special Function: This option offers coding, reset, relearn, and more service functions to help vehicles get back to functional status after repair or replacement.
5.6 Remote Diagnose
This module helps repair shops or technicians launch remote diagnosis on a vehicle, improving repair efficiency and getting tough repair job fixed faster. This remote diagnosis can be performed between:
- The scan tool and other LAUNCH-specific scan tools, which are equipped with this module.
- The scan tool and PC client technician (based on web-based remote diagnosis platform http://remote.x431.com/).
Tap Remote Diagnose on the Job menu, the following screen will appear:
- Messages tab: Tap it to display a list of messages you have involved in.
- Contacts tab: Tap it to show your friend or partner list. Only the technical support is displayed by default if no friend is added.
- Remote tab: This function allows you to request remote help from the PC client technician.
- Home button: Navigate to the Job Menu screen.
Note: The partner must be the users who have registered their Launch-specific diagnostic tools. They may be the following: workshop / technician / golo users.
To launch remote diagnosis with the partner not in your friend list:
- Tap Contacts. In the search bar, input the partner's username or serial number of the scan tool, and tap Search.
- When searching is finished, tap Remote Diagnose on the right of the username or the technician's avatar to proceed.
- Choose the desired diagnostic software (this step only applies to the INVITE REMOTE DIAGNOSE ASSISTANT).
- Wait for the partner's confirmation.
- Start connection after the request is accepted.
- Start diagnosis and generate remote diagnostic report.
In the process of remote diagnosis, note the followings:
- You are not suggested to execute any actions.
- The partner is not allowed to save any diagnostic reports or records on your tool.
Once the session is complete, a remote diagnostic report will be automatically generated.
6. Software Update
This module enables you to update the diagnostic software & App and frequently used software.
6.1 Update Diagnostic Software & APP
Go to Software Update on the Job Menu and tap the Downloaded tab. The Available tab displays a list of software that can be updated. Under it, all software is categorized into three kinds:
- Common software: mainly includes some common apps that are associated with the diagnostic app. The software of this kind always stays at the top of the list, which can be deselected manually (excluding the system app, such as firmware and ECU aid).
- Frequently used vehicle software: refers to the diagnostic software that is frequently used, including the vehicle diagnostic software and Reset software. It is generally displayed following the Common software list.
- Other vehicle software: refers to the diagnostic software that is rarely used or never used. It is generally displayed following the Frequently used software list.
- If the user does not download any diagnostic software during the sign-up process, all diagnostic software is selected by default. Tap Update to start downloading.
- If the user downloaded all/some vehicle software during the sign-up process and had it serviced for a long period of time, only the frequently used software is selected. Tap Update to start downloading. Other vehicle software that is rarely used will also be listed under the Available tab, but it is not selected by default.
To download certain software that is not frequently used, check the box before the vehicle model. Tap Update to start downloading. Once download is finished, the software packages will be installed automatically.
6.2 Update Frequently Used Software
If the user only intends to update the frequently used software, go to Software Update and tap the Downloaded tab. Tap Update to start downloading. Once download is finished, the software packages will be installed automatically.
6.3 Renew Subscription
If the software subscription is due or expires, the system will prompt you to renew your subscription. Tap Renewals to open the Mall, and the follow the on-screen prompts to finish the subscription.
7. Toolbox (Extended Modules)
The LAUNCH X431 PRO Elite supports various extended modules to enhance its capabilities. These modules are sold separately.
7.1 TPMS (Tire Pressure Monitoring System)
This module allows you to configure the scan tool as TPMS activation & diagnostic tool, which provides the ability to trigger TPMS sensor, program TPMS sensor, perform the relearning procedure. It needs to work with the compatible TSGUN device (sold separately).
7.2 ADAS (Advanced Driver-Assistance Systems) Calibration
This module enables you to effectively and accurately calibrate a wide range of camera-based & radar-based driver assistance systems, e.g. the front camera for the lane departure warning system, the radar sensor for the ACC (Adaptive Cruise Control) or the camera for adaptive headlights. It needs to work with the specific ADAS calibration tool (sold separately).
7.3 Oscilloscope
This module can make the auto repair technician quickly judge the faults on automotive electronic equipment and wiring. It needs to work with the specific Scopebox (sold separately).
7.4 Sensor Simulator
This module is specially designed to diagnose and simulator vehicle sensor faults quickly and conveniently. It needs to work with the compatible S2-2 Sensorbox (sold separately).
7.5 Videoscope
This module allows you to check those unseen parts of engine, fuel tank, and braking system etc. It needs to work with the compatible Videoscope (sold separately).
7.6 BST360 (Battery Tester)
This module allows you to fix battery detection faster and easier. It needs to work with the specific Bluetooth battery tester (sold separately).
7.7 Multimeter
This module allows you to measure the physical parameters such as voltage, resistance, frequency etc. It utilizes the same hardware as the EM101N.
7.8 Current Clamp
This module allows you to perform AC/DC current test and DC voltage test for traditional fuel cars and new energy vehicles. It needs to work with the compatible current clamp (sold separately).
7.9 Insulation Tester
The module enables you to complete the measurement of insulation resistance, voltage and other parameters. It is suitable for users who measure and overhaul on-site power equipment and power supply lines.
7.10 Immobilizer Programmer
This module allows you to perform the read-write function for vehicle keys, EEPROM, MCU, and EEPROM/FLASH of vehicle engine and gearbox ECU. It needs to work with the specific immobilizer programmer (sold separately).
7.11 Key Programmer
The module can identify car key chips and generate various types of chip models from super remotes, read the remote-control frequency of car keys, and generate remote control devices for different car models from various types of super remotes. It needs to work with the compatible key programmer (sold separately).
8. X-431 Diagnosis Kit
8.1 Vehicle Coverage
This option allows you to check which vehicle models are supported on the tool.
8.2 DLC Voltage Check
This option allows you to perform a check of the vehicle's battery to ensure the system is operating within acceptable limits.
8.3 Diagnostic Software Clear
This option allows you to hide/clear the diagnostic software that is not frequently used.
Note: Removing software may completely delete the software from the scan tool. If some software is not used and the scan tool runs out of space, you can use this feature to remove it. To re-download it, go to Software Update -> Available.
8.4 Fix Connector Firmware
This option allows you to upgrade and fix VCI firmware. During fixing, please do not cut power or switch to other interfaces.
8.5 Data Stream Sample
This option allows you to manage the recorded data stream sample files.
8.6 Reset MSVIN
This option can decode the VIN information of all ECUs installed on test vehicle and output all inconsistent VINs.
8.7 Diagnostic History
This option offers convenient access to previously tested vehicle records, allowing users to resume from the last operation without needing to start anew.
9. User Info
This function allows you to manage personal information and VCI.
9.1 My Report
This option is used to view, delete or share the saved reports or recorded data. Tap My Report, there are total 3 options available.
- If the DTC result is saved on Read Trouble Code page, the files will be listed under Health Reports tab.
- Remote Reports lists all diagnostic reports generated in process of remote diagnosis.
- If user records the running parameters while reading data stream, the scan tool will save the file under Recorded Data tab.
9.2 VCI
This function allows you to manage all your activated VCI devices.
9.3 Activate VCI
This function enables you to activate a new VCI in the event you missed the Activate VCI step during the product registration process.
9.4 Profile
This function allows you to view and configure personal information.
9.5 My Order
This function allows you to check the status of all your orders.
9.6 Change Password
This function allows you to modify your login password.
9.7 Login/Log out
To logout the current user ID, tap Log Out. To login the system again, tap Login.
10. Settings
It enables you to make some application settings.
10.1 Units
This function enables you to set the measurement unit. Metric System and English System are available.
10.2 Shop Information
This function enables you to define your shop information. After you saved the shop information, it will be filled automatically in the "Add Information" box every time you save a diagnostic report.
10.3 Printer Set
This option is designed to establish a wireless connection between the scan tool and the Wi-Fi printer (sold separately) while performing printing operations.
The App is compatible with the LAUNCH Wi-Fi Printer (sold separately) and System (external printer).
For LAUNCH Wi-Fi printer, refer to the user manual included with the printer to configure it.
For other Wi-Fi printers:
Before printing, make sure that the Wi-Fi printer is powered on and working normally.
Follow the steps below to proceed:
- Set the default printer as System.
- Set the Wi-Fi switch to On.
- Tap the desired Wi-Fi printer hotspot to connect.
- On the report details page, tap the printer icon.
- Touch next to Select a printer to select the desired Wi-Fi printer from the list. If the chosen Wi-Fi printer hotspot is enabled, the tool can connect to it directly. If it is encrypted, a password may be required. See the Wi-Fi printer user manual for the default password.
- Now the printer is ready for printing.
Alternatively, you can also choose Save as PDF to save the current diagnostic report as a PDF file for later printing.
10.4 Clear Cache
This function enables you to clear the app cache. Clearing cache will result in the app restarting.
10.5 Diagnostic Software Auto Update
This function is used to set whether automatic update function is ON.
10.6 Device Account Management
This function manages sub-accounts, enabling the use of the tool by different users and facilitating the tracking of diagnostic logs from various technicians. Newly added sub-accounts have a one-year validity period. After expiration, they lose the rights and privileges of the main account. However, the main account can modify the validity period of the sub-account.
There are two types of sub-accounts: existing accounts and newly created ones. The main account has the ability to add and remove sub-accounts, while sub-accounts can also be unbound from the main account.
Tap Device account management, the following screen will appear:
- If you already have an account, please enter the username and password. After inputting, tap Add Immediately to add it as a sub-account.
- If you have not registered any account, tap new technician account to create a sub-account.
After adding the sub-account, user can tap Remove to unbind it from the main account or tap Change to revise the validity period.
11. Troubleshooting (FAQs)
11.1 How to save power?
- Please turn off the screen while the tool keeps idle.
- Set a shorter standby time.
- Decrease the brightness of the screen.
- If Wi-Fi connection is not required, please turn it off.
- Disable Global Positioning System (GPS) function if GPS service is not in use.
11.2 Communication error with vehicle ECU?
Please confirm:
- Whether the scan tool is correctly connected.
- Whether ignition switch is ON.
- If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature.
11.3 Failed to enter into vehicle ECU system?
Please confirm:
- Whether the vehicle is equipped with this system.
- Whether the scan tool is correctly connected.
- Whether ignition switch is ON.
- If all checks are normal, send vehicle year, make, model and VIN number to us using Feedback feature.
11.4 How to download the diagnostic App after resetting the scan tool?
Note: Before registration, please make sure the network is properly connected. If the scan tool has been reset to the factory settings or the diagnostic app has been uninstalled, follow either of the following methods to download the App.
Method 1 - Via APP Init
- On the Android's home screen, tap the mini program APP Init to run it.
- The program automatically obtains the Serial Number of the diagnostic tool. Carefully check the product Serial Number information against the included Password Envelope. If consistent, tap OK to start downloading and installing.
- After the downloading and installation is completed, the following screen will appear.
Method 2 - Via official website
- Open the browser and the default official LAUNCH website opens (If a blank page pops up, just type in https://en.cnlaunch.com in the input bar).
- Go to Service -> Downloads & Upgrade to download the target App.
11.5 What to do if the language of vehicle diagnostic software does not match the system language?
English is the default system language of the tool. After the system language is set to the preference language, please go to the update center to download the vehicle diagnostic software of the corresponding language.
If the downloaded diagnostic software is still displayed in English, it indicates that the software of the current language is under development.
11.6 How to retrieve the login password?
Please follow below steps to proceed in case you forgot the login password:
- Tap the application icon on the home screen to launch it.
- Tap Login on the upper right corner of the screen.
- Tap Set/Reset Password.
- Input product S/N and follow the on-screen prompts to retrieve the password.
11.7 How to backup system data?
There are two USB ports available on this tool: USB Type-A and USB Type-C. The former is reserved for external USB storage device and the latter is used with PC when performing system data backup. It is strongly recommended to use the USB Type-C interface for this operation.
A. If exchanging data with an external USB storage device,
- Plug the USB storage device into the USB Type-A interface.
- Swipe the screen from the top to select the USB drive.
- Now you can exchange the data with the USB storage device.
B. If exchanging data with a PC,
- On the home screen, tap Settings -> USB Management. Slide the USB Switch to OFF to enable the USB Type-C interface.
- Plug the Type-C end of the included data cable into the Type-C port of the tool, and the other end to the USB port of the PC.
- After the PC successfully identifies the tool, you can perform data backup.
12. Specifications
| Attribute | Value |
|---|---|
| Brand Name | LAUNCH |
| Model Name | X431 PRO ELITE |
| Item Type | Engine Analyzer |
| Operating System | Android 10.0 |
| Processor | 2.0GHz Quad-Core |
| RAM | 4GB |
| Storage | 64GB |
| Display Size | 8 inches |
| Display Resolution | 1280 x 800 High-Resolution |
| Camera | Rear-facing 8.0MP |
| Communication Interface | Bluetooth, Wi-fi (5G/2.4GHz) |
| USB Ports | Type-A x 1 + Type-C x 1 |
| Battery | 6000 mAh |
| Item Weight | 4.1kg |
| External Testing Certification | CE |
| Software Update | Yes (2 years Free Update) |
| OE-Level All systems diagnostics | Yes |
| Support 31+ Reset Services | Yes |
| CANFD & DOIP PROTOCOL | Yes |
| Full Bidirectional Control (Active Test) | Yes |
| Wider & Newer 150+ car makes coverage | Yes (200,000+ Vehicle Coverage) |
| VAG Guided Function | Yes |
| AutoAuth for FCA | Yes |
| Online Coding | Yes |
| Flash Hidden Functions | Yes |
| Anti-theft IMMO Service | Yes |
| Advanced ECU Coding | Yes |
| Auto VIN Scan | Yes |
| 25 Languages Free to Use | English, French, Spanish, German, Russian, Korean, Japanese, Portuguese, Italian, Polish, Dutch, Hungarian, Finnish, Czech, Turkish, Greek, Arabic, Danish, Romanian, Serbian, Swedish, Traditional Chinese, Thai, Persian, Simplified Chinese. |
| Key Programming | Program Key FOBs, All Keys Lost, Add & Disable Key, Key Coding |
| Warranty | 3 years |
13. Warranty and Support
Warranty
This warranty is expressly limited to persons who purchase LAUNCH® products for purposes of resale or use in the ordinary course of the buyer's business.
LAUNCH® electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with stipulated procedures.
Customer Service
If you have any questions during the operation of the unit, please contact the Seller, or contact LAUNCH TECH Service Center.
- Website: https://en.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com
To reduce roundabout time, you need to clearly indicate your product Serial Number when providing issue feedback.
For a detailed user manual in PDF format, please refer to the official document: User manual (PDF).
14. User Tips
- The device is global, meaning it can be used internationally.
- The product is of excellent quality and a great tool for diagnostics.
- The software will not be blocked after the 2-year free update period; you can continue to use the full software normally.