Casubaris TM500-318

Contents

Casubaris TM500-318 Portable Mini Airbrush Compressor User Manual

Model: TM500-318

1. Introduction

Thank you for choosing the Casubaris TM500-318 Portable Mini Airbrush Compressor. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your airbrush kit. Please read it carefully before use and keep it for future reference.

1.1 Electrical Safety Warnings

  • Do not expose the compressor to rain or wet conditions. Water entering a compressor will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for unplugging the compressor. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
  • Do not turn on the compressor while charging.

IMPORTANT: Please read this manual carefully before running this airbrush compressor & airbrush kit and save it for reference.

2. Package Contents

Please check the box for the following items:

  • TM500 Compressor
  • 318 Dual Action Airbrush Pen
  • Battery (pre-installed in the compressor)
  • Type-C USB Charging Cable
  • Hose (1.2M)
  • Pen Holder
  • Shoulder Strap
  • Cleaning Brushes
  • User Manual
  • Box
All components of the Casubaris TM500-318 airbrush kit laid out
Figure 2.1: Complete Airbrush Kit Contents

3. Specifications

Feature Specification
Power 20W 3.7V 8000mAh
Working Pressure 15psi
Auto Stop Pressure 28psi
Motor Pressure 45-50psi (50psi peak)
Air Flow 7-10 L/min
Charging Time (5V 2A charger) Approx. 4-5 hours
Charging Time (5V 1A charger) Approx. 8-10 hours
Continuous Working Time 50-80 minutes (actual runtime often exceeds 2 hours due to auto-stop)
Material Aluminum alloy / HDPE
Nozzle Diameter 0.3mm
Cup Volume 7CC
Hose Length 1.2 M
Connector G1/8 Female
Weight 35.27oz (1kg)
Certification CE, FCC, RoHS

4. Setup

4.1 Battery Installation

The battery is replaceable. To install or remove the battery, press down on the battery pack and slide it into or out of the compressor slot.

Diagram showing how to install the battery into the compressor
Figure 4.1: Battery Installation

4.2 Component Assembly

  1. Connect one end of the air hose to the air outlet on the compressor.
  2. Connect the other end of the air hose to the airbrush.
  3. (Optional) Attach the pen holder to the compressor.
  4. (Optional) Attach the shoulder strap to the compressor for portable use. The strap secures the air pump in place and provides thermal insulation.
Diagram of the compressor highlighting features and connection points
Figure 4.2: Compressor Features and Connections
User wearing the compressor with a shoulder strap
Figure 4.3: Portable Use with Shoulder Strap

4.3 Initial Check

Turn on the power switch and inspect all air connections for leaks. If any leaks are found, turn off and unplug the airbrush compressor, then repair the leaks before proceeding.

5. Operation

5.1 Power On/Off and Pressure Adjustment

  1. Press the upper part of the button on the compressor lightly to turn it on.
  2. Adjust the air pressure by rotating the knob on the compressor. It can be freely adjusted between gears 1 and 10.
  3. To turn off, press the button again.
Diagram illustrating how to adjust the air pressure using the knob
Figure 5.1: Air Pressure Adjustment

5.2 Dual Action Airbrush Pen Operation

The 318 Dual Action Airbrush Pen allows for precise control of both air volume and paint flow.

  1. Press the trigger on the airbrush pen to blow air out.
  2. Press the trigger and pull it backwards to spray liquid from the cup.
  3. Release your finger to stop spraying.
Diagram labeling the parts of the airbrush: 0.3mm Nozzle, 7cc Gravity Feeding Cup, Dual Action Switch, 1/8 Hose Connector, Adjusting Screw, Tail Handle Adjusting Screw.
Figure 5.2: Airbrush Components

5.3 Painting Procedure

  1. Ensure the workpiece is clean, free of dust, oil, and other impurities. Mask off areas that do not need to be sprayed.
  2. For small workpieces (e.g., models), hang or place them on a stand for easy access to all areas.
  3. Keep the airbrush nozzle approximately 6 inches (15 cm) away from the workpiece.
  4. Use short, even strokes for spraying, moving parallel to the work surface at a steady speed.
  5. For full coverage, apply a light coat, allow it to dry, then apply a second coat. Repeat until the desired coverage is achieved. Do not attempt to achieve full coverage with a single spray pass.
Compressor on a tabletop next to a model kit, showing its use for spray painting
Figure 5.3: Airbrush in use for model painting

5.4 Applications

This airbrush kit is suitable for a wide range of applications, including:

  • Commercial art
  • Painting (e.g., models, crafts)
  • Makeup
  • Illustrations
  • Temporary tattoos
  • Cake decorating (edible printers)
  • Nail design
  • Tanning
  • Shoe painting (e.g., sneakers)
Diagram illustrating various applications of the airbrush kit
Figure 5.4: Diverse Applications of the Airbrush Kit

6. Maintenance

6.1 Cleaning the Airbrush

Regular cleaning is crucial to prevent blockages and ensure optimal performance. Clean the airbrush immediately after each use.

  1. Add cleaning solution to the cup.
  2. Perform a bubble cleaning: block the nozzle with your finger, then press and pull the trigger 3-4 times to backflush.
  3. Repeat steps 1 and 2 until the cleaning solution runs clear.
  4. Add fresh cleaning solution and spray it out through the nozzle.
  5. Disassemble the airbrush and clean all components thoroughly with the provided cleaning brushes.
  6. Install the spray pen after cleaning and ensure it is completely dry before storage.
Diagram showing the steps for cleaning the airbrush to prevent blockage
Figure 6.1: Airbrush Cleaning Procedure

6.2 General Care

  • Before each use, inspect the overall condition of the airbrush compressor, including loose hardware, misalignment or jamming of moving parts, cracked or damaged parts, and damaged wires.
  • Store the airbrush compressor in a clean, dry, and safe place, out of reach of children and unauthorized personnel.
  • This air compressor is designed for low-density dyes (makeup, beauty, nail, temporary tattoos, cake decorating, etc.) and should not be used for spraying thick paint.
  • Always test the airbrush with water first to ensure normal atomization before using paint.
  • Handle the unit with care; dropping it may affect its performance or cause damage.
  • For changing the needle and nozzle, professional assistance is recommended to protect the item.

7. Troubleshooting

Problem Possible Cause Solution
No air or weak airflow Clogged nozzle/airbrush, low battery, loose hose connection. Clean the airbrush thoroughly. Charge the battery. Check and tighten all hose connections.
Paint sputtering or uneven spray Paint too thick, partially clogged nozzle, incorrect pressure setting. Thin paint appropriately. Clean the airbrush. Adjust air pressure.
Compressor not turning on Battery depleted, faulty power switch. Charge the battery. If the issue persists, contact customer support.
Battery overheating during charging Faulty battery or charger, improper charging conditions. Immediately disconnect from power. Do not use the battery or charger. Contact customer support for replacement.
Excessive noise from compressor Normal operation (some noise is expected), internal issue. While generally quiet, some noise is normal. If noise is unusually loud or changes, contact customer support.

8. User Tips

  • The auto-stop function helps conserve battery life, allowing for longer actual working sessions than the continuous runtime suggests.
  • The compressor's low noise level makes it suitable for use in quiet environments, such as at night.
  • The pressure is generally sufficient for acrylic paints and various model kits.
  • Consider purchasing an extra battery for extended work sessions, as a full charge can take several hours. Extra batteries can be purchased from the seller or authorized retailers.
  • For optimal painting results, ensure the output is increased to a comfortable level.

9. Warranty & Support

9.1 Warranty Information

The TM-500 Airbrush Compressor is covered by a 90-day limited warranty from the date of purchase against defects in materials and workmanship. Proof of purchase is required for all warranty claims.

This warranty is VOID if:

  • Damage results from misuse, improper operation, or dropping the unit.
  • Unauthorized repairs, modifications, opening, or disassembly occur.
  • The unit is not used according to the instructions provided in this manual.

9.2 Customer Support

If you encounter any problems during use or have questions not covered in this manual, please contact our After-Sales Service Department. Our team is ready to assist you with troubleshooting and support.

For inquiries, please refer to the contact information provided by your seller or on the product packaging.

10. Product Demonstration Video

Watch this video for a visual guide on the product's features and operation.

Video 10.1: Casubaris TM500-318 Airbrush Compressor Demonstration
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.