Product Overview
This product provides enhanced visibility and safety for your vehicle with integrated Daytime Running Lights (DRL), Fog Lights, and Turn Signal functions. Designed as direct replacement parts, these lamps offer a seamless upgrade for compatible Toyota Prius models.
Figure 1: Product overview displaying DRL (white), Turn Signal (yellow), and Fog Light modes.
Video 1: Demonstration of the LED Dual Color DRL, Fog Light, and Turn Signal Lamps in operation.
Safety Information
- Always disconnect the vehicle's battery before performing any electrical work.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Professional installation is highly recommended to ensure correct wiring and functionality.
- Verify local regulations regarding automotive lighting before installation.
Package Contents
- 2 x LED Dual Color DRL, Fog Light, and Turn Signal Lamps (Left and Right)
- Wiring Harness (pre-attached or separate, as per model)
Setup and Installation
These lamps are designed as direct replacement parts for the original bumper lights. Follow these general steps for installation. It is strongly recommended to have this product installed by a qualified automotive technician.
- Preparation: Park your vehicle on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative terminal of the vehicle's battery.
- Access: Depending on your vehicle model, you may need to remove parts of the front bumper or fender liner to access the existing lights.
- Remove Old Lights: Carefully disconnect the wiring from the existing lights and unmount them from the bumper.
- Wiring Connection: Connect the new LED lamps using the provided wiring harness. Refer to the wiring diagram below for specific connections:
- Red Wire: Connect to ACC+ (Accessory Power) or DRL (Daytime Running Light) positive terminal.
- Blue Wire: Connect to Fog Light positive terminal.
- Plug-and-Play Connector: Connect to the factory turn signal connector.
- Mount New Lights: Securely mount the new LED lamps into the bumper openings.
- Test Functionality: Reconnect the vehicle's battery. Turn on the ignition and test all light functions (DRL, Turn Signal, Fog Light) to ensure they operate correctly.
- Reassemble: Reinstall any removed bumper or fender liner components.
Figure 2: Detailed wiring diagram for installation.
Figure 3: Example of installed lamps on a Toyota Prius ZVW30.
Operating Instructions
The LED lamps integrate three primary lighting functions:
- Daytime Running Lights (DRL): These lights emit a bright white light and are typically active when the vehicle's ignition is on, enhancing daytime visibility.
- Turn Signal Lamps: When the vehicle's turn signal is activated, the lamps will flash in a distinct yellow/amber color, indicating your intended direction.
- Fog Lights: These lights emit a white light and are activated via your vehicle's fog light switch, providing additional illumination in adverse weather conditions. They can operate independently or in conjunction with DRL/Turn Signals.
Figure 4: DRL (White Light) operation.
Figure 5: Turn Signal (Yellow Light) operation.
Figure 6: Combination modes including DRL & Fog Light, Turn Signal & Fog Light, and Fog Light only.
Maintenance
- Cleaning: Regularly clean the lamp lenses with a soft cloth and mild automotive cleaner to maintain optimal light output. Avoid abrasive cleaners.
- Inspection: Periodically check the lamps for any signs of damage, loose connections, or moisture ingress.
- Bulb Replacement: As these are LED units, individual bulb replacement is generally not required. If a unit fails, the entire assembly may need to be replaced.
Troubleshooting
- Lights Not Working:
- Check all wiring connections to ensure they are secure.
- Verify that the vehicle's fuses related to DRL, turn signals, and fog lights are intact.
- Ensure the battery is properly connected and charged.
- Incorrect Light Color or Mode:
- Re-check the wiring connections, especially the red and blue wires, to ensure they are connected to the correct vehicle circuits (ACC+/DRL, Fog Light+).
- Confirm the plug-and-play connector is correctly seated in the factory turn signal socket.
- Moisture Inside Lens:
- Small amounts of condensation can occur due to temperature changes and usually dissipate. If excessive moisture or water accumulation is observed, check for proper sealing and ensure the unit is correctly installed.
Specifications
| Attribute | Value |
|---|---|
| Model Name | LED DRL Daytime Running Light Turn Signal Lamps |
| Item Type | Day Light |
| Voltage | 12 V |
| Material | ABS Housing |
| Fitment | For Toyota Prius ZVW30 2012-2015 |
| Light Color | White DRL and Fog Light + Yellow Turn Signal |
| Origin | Mainland China |
| High-concerned chemical | None |
For more detailed information, please refer to the official user manual PDF: User Manual (PDF)
User Tips
- Ensure the lights are specifically designed for your vehicle's make, model, and year (Toyota Prius ZVW30 2012-2015) for proper fitment and functionality.
- Consider professional installation to guarantee correct wiring and avoid potential electrical issues.
Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.