diymore Lithium Battery Charging Module

Contents

Diymore 3A Lithium Battery Charging Module User Manual

DC 4.5-12V 5V 3A LED Lithium Battery Step-Down Power Supply Charging Module with Charging Protection and Integrated Type-C Interface

1. Product Overview

This module is a compact and efficient power solution designed for charging 3.7V lithium batteries. It features a Type-C input, a step-down power supply using the TI BQ25606 chip, and integrated protection against overcharge and over-discharge. It provides a stable output with a maximum charging current of 3A, making it suitable for various portable applications. On-board LED indicators provide visual feedback on the charging status.

Video: Diymore 3A Lithium Battery Charging Module Overview

Front and back view of the Diymore 3A Lithium Battery Charging Module

Image: Front and Back View of the Charging Module

2. Setup Instructions

2.1 Module Dimensions

Diagram showing the dimensions of the charging module: 26mm length, 17mm width.

Image: Product Size Diagram. Dimensions are approximately 26mm (1.02in) x 17mm (0.67in).

2.2 Pin Description and Connections

Refer to the diagram below for pin identification and connection points. Ensure correct polarity when connecting components to avoid damage.

Wiring diagram showing input positive (V+), input negative (V-), Type-C port, NTC thermistor pins (R1, R2), Load+ (U+), Load- (U-), Power+ (B+), and Power- (B-).

Image: Pin Description Diagram

  • V+ / V-: Input voltage terminals (DC 4.5-12V). Connect your power source here.
  • Type-C: Alternative input for power supply (DC 4.5-12V).
  • B+ / B-: Battery connection terminals. Connect your 3.7V lithium battery here, observing polarity.
  • U+ / U-: Load output terminals. This is where your device or load will draw power from the battery.
  • NTC: Thermistor connection points (R1, R2). By default, the thermistor is not used. If you wish to implement temperature protection (0°C to +60°C range), connect a negative temperature coefficient thermistor (e.g., 103AT-2) here. Note that using an NTC requires modifying the resistance values of R1 to 5.23K and R2 to 30.1K.

2.3 Initial Battery Activation

When connecting a battery for the first time, there might be no voltage output at the U+ / U- terminals. To activate the battery's protection circuit and enable output, you must apply a 5V charging voltage to the module's input (V+/V- or Type-C port).

3. Operating Instructions

3.1 Charging Process

  1. Connect your 3.7V lithium battery to the B+ and B- terminals, ensuring correct polarity.
  2. Connect a DC power supply (4.5-12V) to the V+ and V- terminals, or plug a Type-C cable from a power adapter into the Type-C port.
  3. The module will begin charging the battery.

3.2 Charging Status Indicators

The module features LED indicators to show its operational status:

Table detailing charging status indicators: On for charging, Out for termination, Off for sleep/disabled, Flashing at 1Hz for pause/error.

Image: Charging Status Indicator Table

  • Red LED: Indicates charging status. Refer to the table above for specific states.
  • Blue LED: Indicates the charging power supply is good. It should remain constantly on when a valid power supply is connected.

3.3 Important Operating Notes

  • Power Supply Current: If using a mobile phone charger as a power supply, it must be capable of outputting more than 1A for proper charging.
  • Load Current Limits: This module is not designed for high-power applications. It is recommended to operate with a load current below 2A. If the load current exceeds 2A, additional cooling fins must be added to dissipate heat.
  • Inductive Loads: Avoid connecting high inductive loads, as their high starting current can damage or burn out the module, even if the nominal current is within limits.
  • Charging Speed vs. Effect: Faster charging speeds may result in a less efficient charge, leading to a greater voltage drop in the battery after charging is complete.

4. Maintenance

This module is a sensitive electronic component. To ensure its longevity and proper function:

  • Keep the module dry and away from moisture.
  • Avoid exposing the module to extreme temperatures or direct sunlight.
  • Handle with care to prevent physical damage to components or solder joints.
  • There are no user-serviceable parts inside the module. Do not attempt to disassemble or modify it.
  • Clean the module gently with a dry, soft cloth if necessary. Avoid using liquids or solvents.

5. Troubleshooting

  • No output at U+ / U- terminals after connecting battery: This is normal for the first connection. Apply a 5V charging voltage to the module's input (Type-C or V+/V-) to activate the protection circuit.
  • Battery not charging or charging slowly:
    • Ensure your power supply provides sufficient current (at least 1A, especially for mobile phone chargers).
    • Check all connections for proper polarity and secure contact.
    • Verify the input voltage is within the DC 4.5-12V range.
    • If an NTC thermistor is connected, ensure the battery temperature is within the 0°C to +60°C range.
  • Module overheating:
    • Reduce the load current.
    • If operating above 2A, ensure adequate cooling (e.g., attach cooling fins).
    • Avoid short circuits on the output.
  • LED indicators not behaving as expected: Refer to the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.