THINKCAR VENU 90

Contents

THINKCAR VENU 90 TPMS Diagnostic Tool User Manual

1. Introduction

The THINKCAR VENU 90 is a professional Tire Pressure Monitoring System (TPMS) diagnostic tool designed for comprehensive tire sensor management. It supports activation, reading, copying, writing, and programming of tire pressure sensors, along with full OBD2 functions and TPMS diagnostics. This manual provides detailed instructions for setting up, operating, and maintaining your VENU 90 device.

THINKCAR VENU 90 main features
Figure 1: THINKCAR VENU 90 Key Features. Supports 98% vehicles, full OBD2 functions, TPMS diagnostic, sensor activation/learning, programming THINKCAR S1/S2/S3/VENU sensors, 315MHz/433MHz frequency, free WiFi update, 2.8-inch screen, 3000mAh battery, no app needed, 15 languages.
Sensor Activation with VENU 90
Figure 2: Sensor Activation. The VENU 90 activates all 315MHz/433MHz tire pressure sensors, reads, copies, and writes sensor IDs. It also supports sensor learning, displaying sensor frequency, position, ID, tire pressure, temperature, and battery power.

2. Device Overview

Familiarize yourself with the components and controls of your THINKCAR VENU 90 device.

THINKCAR VENU 90 Device Diagram
Figure 3: VENU 90 TPMS Activation and Diagnostic Tool - Quick Start Diagram.

2.1. Product Components and Functions

No.NameFunction
1On/KeyLong press to turn on/off the device.
2Activation keyPress to activate the tire pressure sensor.
3Return keyReturn to previous level.
4OK Ok keyConfirmation button is pressed to go to the next step.
5Flip-up keySwitch tires or turn pages upwards.
6Flip down keySwitch tires down or turn the page.
7Flip left KeySwitch tires to the left or turn the page.
8Flip right KeySwitch tires to the right or turn the page.
9Charging portTYPE-C charging port and development system debug USB port.
10SD card slotSD card storage.

3. Setup

3.1. Powering On

To power on the device, long press the On/Key button (No. 1 in Figure 3). The device will vibrate, display a boot animation, and then enter the main boot interface.

3.2. Wi-Fi Connection and Software Update

The VENU 90 supports lifetime free updates via Wi-Fi. To connect to Wi-Fi and update the software:

  1. From the main menu, navigate to [Set Up].
  2. Select [WiFi Upgrade].
  3. Go to [WiFi List] and wait for the device to scan for available Wi-Fi networks.
  4. Once the search is complete, select your desired Wi-Fi network from the list.
  5. Use the navigation keys (Flip-up, Flip down, Flip left, Flip right) to enter the correct Wi-Fi password.
  6. Press the activation button to connect.
  7. The system will automatically compare the current software version with the latest available. If an update is available, follow the on-screen prompts to proceed. Do not operate the device during the update process.
  8. After the download is complete, the device will automatically reboot with the updated software.

4. Operating Instructions

The VENU 90 offers various functions for TPMS and OBD diagnostics. Here's how to use them:

4.1. Tire Pressure System Functions

From the main interface, select [Tire Pressure System] to access TPMS-related functions. The general workflow involves entering the tire pressure system, selecting the vehicle's brand, series, and year, then accessing the specific TPMS function.

4.1.1. Check Sensor

This function activates the tire pressure sensor to read its data.

  1. Select [CHECK SENSOR] from the menu.
  2. Follow the on-screen prompts to activate the sensor in the tire according to the indicated tire position.
  3. Use the navigation keys (Flip-up, Flip down, Flip left, Flip right) to change the tire position if needed.
  4. After successful activation, the device will display the tire's pressure, temperature, and ID information.

4.1.2. Program Sensor

This function allows you to program new THINKCAR sensors. Select [PROGRAM SENSOR] to enter the programming menu.

Way 1: Create Sensor

The system automatically generates a new sensor ID.

  1. Select [CREATE SENSOR].
  2. Place the THINKCAR sensor in the designated programming area on top of the device.
  3. The device will program the sensor. After programming, return to the activation page and activate the newly programmed sensor.
  4. Note: The [RELEARN] function is required after programming and activating a sensor created this way.

Way 2: Manual Input

If you have the original sensor ID, you can manually enter it.

  1. Select [MANUAL INPUT].
  2. Select the vehicle tires you wish to program.
  3. Enter the 8-character sensor ID using the on-screen keyboard.
  4. Place the THINKCAR sensor on the device and press OK to program.
  5. Note: If you manually create a Sensor ID, a [RELEARN] function is needed after activation. If you enter an existing original sensor ID, relearn is not required.

Way 3: Copy ID by Activate

This method copies the ID from an existing sensor to a new THINKCAR sensor.

  1. Select [COPY ID BY ACTIVATE].
  2. Activate the original vehicle sensor. The sensor data will be displayed on the device.
  3. Select the corresponding tire and press OK to copy the original sensor ID.
  4. Place the new THINKCAR sensor near the top of the VENU 90 device and press OK to program.
  5. The programmed sensor can then be mounted directly on the tire, and the vehicle's TPMS warning light should automatically turn off.
  6. Tip: Ensure the original sensor can be activated before using this method.

Way 4: Copy ID by OBD

This method reads sensor IDs from the vehicle's ECU via the OBD port and programs them to new sensors.

  1. Connect the VENU 90 to the vehicle's OBD diagnostic port.
  2. Select [COPY ID BY OBD]. The device will read the vehicle's sensor data.
  3. Select the tire you wish to program. The system will automatically enter sensor programming.
  4. Place the new THINKCAR sensor on the device and press OK to program.
  5. After programming, the new sensor can be mounted and used.

Way 5: Create Multi-Sensor (1-12)

This function allows programming up to 12 THINKCAR VENU sensors simultaneously.

  1. Select [CREATE MULTI-SENSOR (1-12)].
  2. Place the sensors to be programmed right above the device, within 10cm.
  3. The device will automatically detect and program the sensors. The sensor IDs will be displayed upon successful programming.

4.1.3. Relearn Procedure

After replacing or programming TPMS sensors, the vehicle's ECU needs to learn the new sensor IDs. Select [RELEARN PROCEDURE] to view the vehicle's specific learning method.

Relearn Types:

  • OBD Relearn: Follow the on-screen prompts. This may involve activating all TPMS sensors, connecting the OBD line, and confirming on the device.
  • Copy ID by OBD: Requires connecting to the vehicle's OBD port and turning on the ignition.
  • Copy ID by Activate: After activating the original sensor and confirming the tire to be replaced, the device copies the ID and programs the new sensor. This is only used if the original sensor is still activatable.

4.1.4. TPMS OBDII

This section provides advanced TPMS diagnostic functions via OBD-II.

  • Read ID: Reads sensor IDs stored in the vehicle's ECU.
  • Read Code: Reads TPMS-related vehicle fault codes (DTCs).
  • Erase Code: Clears TPMS-related vehicle fault codes.

4.1.5. OE Sensor Info

Access this feature to view factory sensor information for Original Equipment (OE) sensors.

4.2. OBD Detection

To perform OBD testing, connect the VENU 90 to the vehicle's OBD interface. The location of the diagnostic seat can often be found in [Set Up] > [DLC location information].

The main diagnostic menu includes:

  • Read Codes: Reads vehicle fault codes. You will need to manually select the vehicle manufacturer.
  • Erase Codes: Clears vehicle fault codes. Follow device prompts to turn on the switch, turn off the engine, and confirm.
  • I/M Readiness: Checks the readiness of the monitoring system for emission compliance.
  • Data Stream: Queries real-time PID data from the vehicle ECU (analog/digital inputs/outputs, system status).
  • Freeze Frame: Displays data recorded at the moment a fault code was set.
  • O2 Sensor Test: Tests results of recent oxygen sensor monitoring.
  • On-Board Monitoring: Monitors various vehicle functions.
  • Evap System Test: Initiates a leak test of the evaporative emissions system.
  • Vehicle Information: Reads vehicle details like VIN, calibration IDs, and verification numbers.

4.3. Key Frequency

This function allows you to check the frequency of a vehicle's key fob.

  1. From the main menu, select [Key Frequency].
  2. Place the key fob near the device. The device will display the key's frequency (e.g., 433MHz).

5. Maintenance

  • Keep the device clean and dry. Use a soft, damp cloth to wipe the exterior.
  • Avoid exposing the device to extreme temperatures, direct sunlight, or excessive moisture.
  • Store the device in a safe place when not in use to prevent physical damage.
  • Do not attempt to open or repair the device yourself, as this will void the warranty.

6. Troubleshooting

If you encounter issues with your VENU 90, consider the following:

  • Device not powering on: Ensure the battery is charged. Connect the device to a power source using the TYPE-C charging port.
  • Wi-Fi connection issues: Double-check the Wi-Fi password. Ensure the device is within range of the Wi-Fi router.
  • Sensor activation failure: Ensure the sensor is functional and within range. Check the sensor's frequency (315MHz/433MHz) matches the device's capability.
  • OBD connection issues: Verify the OBD cable is securely connected to both the device and the vehicle's OBD port. Ensure the vehicle's ignition is on.
  • Software update failure: Ensure a stable Wi-Fi connection during the update process. Do not interrupt the device during an update.

For persistent issues, refer to the official THINKCAR website or contact customer support.

7. Specifications

ParameterValue
Product ModelVENU 90
Screen Size2.8 inch
Battery Capacity3000mAH 3.7V
Equipment Size (without cable)205*89*33.5 (mm)
Operating Current≤1A
Operating Temperature-10°C ~ 50°C
Storage Temperature-20°C ~ 60°C
Communication InterfaceOBD-II
Special FeaturesWifi
Item TypeEngine Analyzer
External Testing CertificationCE
Batteries IncludedYes

8. User Tips

  • Always ensure the device's battery is sufficiently charged before starting diagnostic work to avoid interruptions.
  • Keep the device's software updated via Wi-Fi to ensure compatibility with the latest vehicle models and sensor types.
  • When programming sensors, ensure the new sensor is correctly placed on the device for successful data transfer.
  • For OBD functions, always ensure the vehicle's ignition is on (engine off) unless otherwise specified by the diagnostic procedure.

9. Warranty and Support

9.1. Warranty Terms

THINKCAR TECH provides a free warranty for one year from the purchase date for damages caused by defects in materials or workmanship under normal procedures. This warranty applies only to users and distributors who purchase THINKCAR products through normal channels.

The warranty does not cover damages to the equipment or components caused by:

  • Abusing or unauthorized modification.
  • Using the device for non-designed purposes.
  • Operating the device in a manner not specified in the instructions.

Compensation for dashboard damage caused by equipment defects is limited to repair or replacement. THINKCAR TECH is not liable for any indirect or incidental losses. The nature of equipment damage will be judged according to prescribed inspection methods.

9.2. Customer Support

For any inquiries or support, please use the following contact information:

  • Service Line: 1-909-757-1959
  • Customer Service Email: support@thinkcar.com
  • Official Website: www.thinkcar.com (Product tutorials, videos, FAQs, and coverage lists are available here).

Follow THINKCAR on social media:

  • Facebook: @thinkcar.official
  • Twitter: @ObdThinkcar

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.