Honda 46100-S10-013

Contents

User Manual: Car Brake Master Cylinder Assembly

Model: 46100-S10-013

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the 46100-S10-013 Car Brake Master Cylinder Assembly. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Product Overview

The brake master cylinder is a critical component of your vehicle's hydraulic braking system. It converts the mechanical force from the brake pedal into hydraulic pressure, which is then transmitted to the brake calipers or wheel cylinders, engaging the brakes.

Front view of the brake master cylinder assembly

Figure 1: Front view of the brake master cylinder assembly.

Side view of the brake master cylinder assembly

Figure 2: Side view of the brake master cylinder assembly.

Top view of the brake master cylinder assembly

Figure 3: Top view of the brake master cylinder assembly.

3. Specifications

Attribute Value
Manufacturer Part Number 46100-S10-013
OEM NO. 46100-S10-013
Origin Mainland China
High-concerned chemical None
Package Length 28 cm
Package Width 18 cm
Package Height 12 cm
Package Weight 1.0 kg

4. Vehicle Compatibility

This brake master cylinder assembly is compatible with the following Honda models:

  • Honda CR-V (RD1, RD2)
  • Honda City
  • Honda Civic Ferio (EK2, EK3, EK4, EK5, EK8)
  • Honda Civic (EJ7, EK2, EK3, EK4, MB3, MB4)
  • Honda Domani (MB3, MB4, MB5)
  • Honda HR-V (GH1, GH2, GH3, GH4)
  • Honda Integra SJ (EK3)
  • Honda Integra
  • Honda Orthia (EL1, EL2, EL3)
  • Honda Partner (EY7, EY8, EY9)
  • Honda S-MX (RH1, RH2)

Important: Before purchasing and installation, please compare the shape and OEM number of your original vehicle parts. If they are the same, this part can be used. You can also provide your vehicle's VIN code for confirmation.

Diagram explaining VIN code structure

Figure 4: VIN code structure explanation. The VIN code is composed of 17 digits and letters.

5. Installation Guide

5.1. Pre-installation Preparation

  • Ensure the new master cylinder matches the original vehicle in model, port configuration, and pushrod length.
  • Required Tools: Socket wrench, oil drain pan, brake line plugs, clean rags.
  • Brake Fluid: Use DOT3 / DOT4 fluid according to original vehicle standards. Do NOT mix different types of brake fluid.
  • Protection: Brake fluid is corrosive to paint and skin. Rinse immediately with clean water if splashed.

5.2. Removal of Old Master Cylinder

  1. Turn off the engine, apply the parking brake, and disconnect the fluid reservoir level sensor connector.
  2. Seal the brake lines with appropriate plugs to prevent air entry and fluid leakage.
  3. Remove the master cylinder mounting bolts and carefully detach the old master cylinder.
  4. Clean any oil and dirt from the mounting surface in the engine compartment.

5.3. Brake System Bleeding (MANDATORY)

Bleeding the brake system is crucial after master cylinder replacement to remove air and ensure proper brake function.

Exploded view diagram of the brake master cylinder assembly with numbered parts

Figure 5: Exploded view diagram of the brake master cylinder assembly. This diagram shows the various components and their relative positions, which can be helpful during installation and bleeding procedures.

  1. Bleeding Sequence: Rear Right → Rear Left → Front Right → Front Left.
  2. Procedure:
    • Depress the brake pedal firmly.
    • Loosen the bleeder screw.
    • Drain fluid and bleed air.
    • Tighten the screw.
    • Release the pedal.
  3. Repeat this procedure for each wheel until the fluid is clear, no air bubbles are present, and the pedal feels firm without sponginess.
  4. Maintain the reservoir fluid level above the MIN mark at all times during bleeding to prevent air intake.

5.4. Post-installation Inspection

  1. Check for fluid leakage at the master cylinder, brake lines, or connectors.
  2. Verify normal pedal height; the pedal should not feel spongy or sink.
  3. Start the vehicle; the pedal feel should remain consistent with vacuum assist.
  4. Perform a low-speed road test (≤20km/h): Ensure normal braking, no pulling to one side, and no dragging.

5.5. Safety Prohibitions

  • Do NOT drive the vehicle without properly bleeding the brake system.
  • Do NOT use expired, turbid, or water-contaminated brake fluid.
  • Do NOT carry passengers or drive at high speeds before the road test is successfully completed.
  • Stop the vehicle immediately for inspection and repair if any abnormalities occur (e.g., spongy pedal, fluid leakage, abnormal noise).

6. Operation

Once correctly installed and bled, the brake master cylinder operates automatically as part of your vehicle's braking system. When the brake pedal is pressed, the master cylinder generates hydraulic pressure, which is then distributed to the brake calipers or wheel cylinders, causing the brake pads or shoes to engage and slow down or stop the vehicle. Releasing the pedal relieves the pressure, allowing the brakes to disengage.

7. Maintenance

  • Regularly check the brake fluid level in the reservoir. Ensure it is always above the MIN mark.
  • Inspect brake fluid for clarity and color. If it appears dark, turbid, or contaminated, it should be replaced by a qualified technician.
  • Periodically check all brake lines and connections for any signs of leakage or corrosion.
  • Adhere to your vehicle manufacturer's recommended brake fluid change intervals.

8. Troubleshooting

Problem Possible Cause Solution
Spongy Brake Pedal Air in the brake lines; low brake fluid level. Bleed the brake system thoroughly; top up brake fluid.
Brake Fluid Leakage Loose connections; damaged seals or lines. Inspect all connections and lines, tighten or replace as necessary.
Brakes Not Engaging Properly Improper installation; faulty master cylinder; air in system. Re-check installation steps; re-bleed system; consult a professional.
Abnormal Noise During Braking Component interference; air in system; worn brake pads. Inspect for loose parts; bleed system; check brake pads.

If you encounter any issues not listed here or if the suggested solutions do not resolve the problem, it is recommended to consult a certified automotive technician.

9. User Tips

  • Always use new, unopened brake fluid to prevent contamination.
  • When bleeding brakes, ensure the reservoir cap is off and the fluid level is monitored constantly.
  • Consider bench bleeding the new master cylinder before installation to remove initial air.
  • After any brake system work, perform a thorough test drive in a safe area at low speeds.

10. Warranty and Support

For detailed item guides and documents, including a PDF user manual, please refer to the official documentation provided by the seller. A PDF version of the user manual can be found at: User Manual (PDF).

If you have any questions or require technical assistance, please contact the seller or manufacturer directly. Ensure you have your product model number (46100-S10-013) and vehicle details ready when seeking support.

11. Frequently Asked Questions (FAQ)

Q: What type of brake fluid should I use?

A: Always use DOT3 or DOT4 brake fluid, as specified by your vehicle manufacturer. Do not mix different types of brake fluid.

Q: How often should I check my brake fluid?

A: It is recommended to check your brake fluid level at least once a month, or more frequently if you notice any changes in brake performance.

Q: Can I install this part myself?

A: Installation of brake system components requires mechanical knowledge and proper tools. If you are not confident in your abilities, it is highly recommended to have a qualified technician perform the installation to ensure safety.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.